Question about Cars & Trucks

Open Question

How do i bleed the cooling system on rover 75

I have to keep topping up the coolant level and the temperature guage keeps reading that the car is hot and keeps going up and down and the heater only blows out cold air

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
Brian032472
  • 150 Answers

SOURCE: Frequently loss the coolant and

You are losing coolant if you have a coolant pressure tester follow the directions and use it. If you don't when the car is cool use a 50/50 solutuion of water and coolant fill system and check all the listed items carefully with a flash light and look for leaks. It is either a bad hose, cap, water pump or radiator. Your coolant circulates through the dash and the blower blows throught the heater core to produce heat. No coolant no heat. I would also check the passanger side floor for anti freeze or moisture could be a leaking heater core also.

Posted on Nov 02, 2008

Ad
ifixgms
  • 64 Answers

SOURCE: Heater blows cold air.

heater cores clog in taurus. way to know is this--engine fully hot--heat on reach down to the fire wall and grab hold of one of the heater hoses where it hooks to the core--one should be real hard to keep hold of because its that hot. If the other is close to the same the core is not clogged. But if the other is cold to the touch its clogged. You can remove the hoses and shoot garden hose water in one side or the other and break it loose usually

Posted on Apr 07, 2009

gordanddar
  • 477 Answers

SOURCE: temp guage showing hot, not getting any heat for 1992 Mercury Cap

If the hoses to and from the heater core are hot , and you say the heater core is hot , then the only answer is that the air duct that flows into or out of the heater core plenum ( housing ) is not opening.
Heater control on dash borad inoperative.
Not sure about 92 capri , some cars have a cable linkage , some work on vacume motors.
Try to find a haynes manual for your car , they will walk you through almost every step of anything you may ever want to do to your car.

You seem to know what you are doing , but I gotta ask ........the heater core you felt was up behind the dash inside the passenger compartment of the car right ?

Posted on May 10, 2009

  • 401 Answers

SOURCE: 2006 Pontiac Torrent heater blowing cold air

hi
check the heater hoses and if both are hot then the mode door is broken
i have replaced 2 in the torrents(not a nice job)

Posted on Jun 21, 2009

  • 2 Answers

SOURCE: heater blowing cold air

My 2005 Nissan Sentra 1.8s with 55,000 mi. blows cold air from the heater. Coolant not circulating in engine. Lower hose stays cool to touch. Both heater hoses cold. Changed thermostat - didn't fix it. Coolant not leaking or dirty. None in oil - no oil in radiator. Changed worn water pump belt - pump spins freely with no noise or resistance. Cooling fans come on after warm-up. Temperature gauge stays in normal range then jumps to hot and back again. Coolant good to 10 below - didn't freeze here yet. No other problems or repairs to car. Afraid to drive and make worse. Help!

Posted on Oct 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have done the headgasket on my rover 75 with new piston it keeps over heating coolant comes out of header tank but my heater remains cold and pipes going in and out


Check if u have a heater full blast if u get a hot air comes out to it.....if not then water is not properly circulated it doesnt cool the engine if thats ok then check the pump and thermostat and try ti feel the return line of the coolant to the radiator if its gets hot or warm to touch (located on top part of the radiator) means if its just warm water is not circulatibg properly I dont have experience on 75 rover im just telling u how the coolant cools the engine or how does the system flows and its applicable to all cars that has water cooled engine there one exception the air cooled volkswagen hope this might help u out have patient.....lastly did u flush the system after u installed the head gasket? U have something drop in tge engine while changing the head gasket and its causing blockage just a reminder

Nov 27, 2014 | 2005 Rover 75 1.8

1 Answer

Bleeding cooling system


sounds like air in system ...
Leave the radiator cap off, turn the engine on and let it run until the radiator "burps": You will see the coolant level drop and may see or hear a large air bubble come to the top as the system burps.
Keep an eye on the temperature gauge throughout this process

  • Refill the radiator to the top and coolant reservoir as needed. Put the radiator cap back on. Note that if the engine runs hot after this procedure there may have been another pocket of air that "burped." Let the engine cool down and then add more coolant to both the radiator and the coolant reservoir.
  • Apr 18, 2013 | 1998 Chevrolet Cavalier

    1 Answer

    I have a airlock in my cooling system


    you havent stated what model here ,think you have more than one problem now if this is the K series petrol engine then dump the car as its not worth repairing .If the older one with the honda engine then this is well worth keeping and repairing

    Jan 15, 2013 | Rover 75 Cars & Trucks

    3 Answers

    Engine overheating i have replaced the radiator has plenty of water


    replace thermostat.then bleed coolant system, this is how you do it.fill the cooling coolant system with 50 / 50 dexcool and water to raise boiling point,straight water will evaporate boil away cause engine to overheat catch fire thats why you need 50 / 50 mixture antifreeze and water.to bleed coolant system first fill coolant system until coolant stay at the full cold mark on the the coolant overflow jug,then you start engine allow it to idle,place the heater and ac control in any ac setting except max and the temperature control to the highest setting,run engine until lower hose to water pump is hot. with the engine hot run the engine speed up to 3000 rpm and allow it return to idle, repeat this 5 times. slowly open the bleed valve on the thermostat housing or look for bleed valve at the water pump heater hose.open bleed valve for 15 seconds to expel any trapped air.then top off the coolant as necessary,and when top radiator hose hot thermostat open up.keep adding cooling to overflow until coolant level stop at full cold mark dont over fill coolant.if engine seem like overheating while looking at cooling gauge turn off engine wait a while until cool off add more coolant until coolant level stay stable and dont drop any.when open radiator overflow cap use large rag over the radiator cap to keep from getting scald open radiator cap a little at a time but dont open radiator cap until engine cool down first.replace the radiator overflow cap, thermostat,and engine coolant temperature sensor and check the cooling fans fuses and relays see what happens.

    Aug 18, 2012 | 1998 Oldsmobile Intrigue

    1 Answer

    No my alero is overheating. I have replaced the thermostat and waterpump and put a new cap on reservior and im losing coolant out the overflow


    YOU NEED BLEED AIR OUT THE COOLING SYSTEM.WAIT TO ENGINE COOL DOWN.YOUR VECHICLE YOU HAVE TO POUR COOLANT IN THE COOLANT OVERFLOW JUG UNTIL COOLANT LEVEL STAY AT THE FULL COLD MARK.THEN START ENGINE LET IT IDLE A FEW MINUTES WATCH COOLANT IN THE OVERFLOW JUG WHEN IT DROPS ADD MORE COOLANT UNTIL COOLANT LEVEL STAY AT FULL COLD MARK.WHEN COOLANT LEVEL STOP DROPPING IN OVERFLOW JUG.SCREW RADIATOR CAP BACK ON OVERFLOW JUG WATCH ENGINE COOLANT TEMPERATURE GAUGE AS COOLANT TEMPERATURE START CLIMBING TURN OFF ENGINE LET IT SET A WHILE KEEP FROM GETTING SCALDED.TAKE LARGE RAG PLACE OVER COOLANT OVERFLOW JUG CAP SLOWLY OPEN RADIATOR CAP A LITTLE AT A TIME UNTIL PRESSURE RELEASE.REMOVE OVER FLOW JUG CAP.ADD MORE COOLANT UNTIL COOLANT LEVEL AT THE FUL COLD MARK ON THE OVERFLOW JUG.THEN SCREW CAP BACK ON THE OVERFLOW JUG.START ENGINE LET IT IDLE AGAIN WATCH ENGINE COOLANT TEMPERATURE GAUGE WHEN TEMPERATURE GAUGE START CLIMBING.TURN OFF ENGINE WAIT A WHILE.CHECK COOLANT LEVEL IN THE OVER FLOW JUG.DO THIS PROCEDURE UNTIL THE COOLANT LEVEL IN THE COOLANT OVERFLOW JUG STOP DROPPING AND STAY AT FULL COLD MARK,WHEN THE TOP RADIATOR HOSE GET HOT THERMOSTAT OPENING AIR IS OUT THE COOLANT SYSTEM. WHEN ENGINE COOLS DOWN.CHECK COOLANT OVERFLOW JUG COOLANT MUST BE IN THE COOLANT OVER FLOW JUG AT THE FULL COLD MARK WHEN ENGINE COLD. DONT .DONT OVERFILL COOLANT OVERFLOW JUG.KEEP COOLANT IN THE OVERFLOW JUG IF YOU LET COOLANT OVERFLOW JUG RUN DRY AIR WILL BE DRAW IN COOLANT SYSTEM CAUSE ENGINE TO OVERHEAT.

    Aug 12, 2011 | 1999 Oldsmobile Alero

    3 Answers

    I replaced my radiator on my 2004 with a 2.2 and it seems like the thermostat is not opening. It can not get the air out. It seem to just to over heat and push the coolant out. Randy


    REPLACE THERMOSTAT IF TOP COOLANT COOLANT HOSE GOING TO RADIATOR IS HOT TO TOUCH THERMOSTAT OPEN. TO BLEED COOLANT SYSTEM FIRST YOU NEED TO ADD COOLANT TO THE COOLANT OVER FLOW JUG UNTIL COOLANT LEVEL STOP DROPPING AND STAY AT FULL COLD MARK.WAIT 3 MINUTES IF COOLANT DROPS ADD MORE COOLANT UNTIL COOLANT STAY AT FULL COLD MARK.WITH RADIATOR OVER CAP OFF CRANK ENGINE FOR MINUTE WATCH COOLANT LEVEL AT OVERFLOW JUG.IF COOLANT DROPS ADD MORE COOLANT IN THE OVERFLOW JUG.WHEN COOLANT LEVEL STOP DROPPING IN OVERFLOW JUG.SCREW BACK ON THE RADIATOR CAP TO OVERFLOW JUG.WHILE ENGINE IDLING WATCH TEMPERATURE GAUGE WHEN TEMPERATURE START CLIMBING TURN OFF ENGINE WAIT A WHILE KEEP FROM GETTING SCALDED.WHEN COOLANT COOL DOWN SOME. PLACE A LARGE RAG OVER THE COOLANT OVERFLOW JUG OPEN CAP LITTLE AT A TIME UNTIL PRESSURE RELEASED, THEN REMOVE CAP ADD MORE COOLANT IN THE OVERFLOW JUG TO THE FULL COLD MARK.THEN REPEAT THE PROCESS SCREW BACK ON THE COOLANT OVERFLOW RADIATOR PRESSURE CAP.THEN START ENGINE WATCH TEMPERATURE GAUGE WATCH COOLANT TEMPERATURE GAUGE WHEN COOLANT TEMPERATURE START RISING TURN OFF ENGINE AGAIN WAIT UNTIL ENGINE COOL DOWN ENOUGH TO KEEP FROM GETTING SCALDED TAKE PLACE LARGE RAG OVER RADIATOR CAP WHICH IS THE COOLANT OVERFLOW JUG CAP OPEN CAP LITTLE AT A TIME UNTIL PRESSURE RELEASED ADD COOLANT UNTIL AT FULL COLD MARK. WHEN YOUR COOLANT LEVEL STOP DROPPING.AND TOP RADIATOR HOSE VERY HOT THERMOSTAT OPEN AND AIR IS OUT THE COOLANT SYSTEM. MAKE SURE YOUR COOLANT OVERFLOW JUG HAS COOLANT IN IT,WHEN ENGINE COOL DOWN CHECK COOLANT OVERFLOW JUG KEEP COOLANT LEVEL AT FULL COLD MARK.BECAUSE IF OVERFLOW JUG IS EMPTY THATS A SIGN RADIATOR COOLANT LEVEL LOW.WHEN OVERFLOW JUG EMPTY IT WILL ALLOW AIR GET IN THE COOLANT SYSTEM AND CAUSE CAR TO OVERHEAT.WHEN REPLACING THERMOSTAT ALSO REPLACE THE RADIATOR CAP ON THE COOLANT OVERFLOW JUG.

    Aug 09, 2011 | 2004 Oldsmobile Alero

    1 Answer

    Need to know if i need to bleed the cooling system, after installing the radiator?


    ADD COOLANT IN THE COOLANT OVERFLOW JUG UNTIL COOLANT LEVEL STOP DROPPING AND COOLANT LEVEL STAY AT THE FULL COLD MARK.PLACE COOLANT OVERFLOW JUG CAP BACK ON JUG.CRANK VECHICLE UNTIL ENGINE START WARMING UP. STOP ENGINE WAIT FOR A WHILE UNTIL COOLANT COOL DOWN TO KEEP FROM GETTING SCALDED. USE A LARGE RAG OVER THE OVERFLOW JUG CAP OPEN OVERFLOW JUG CAP A LITTLE AT A TIME REMOVE OVERJUG CAP CHECK COOLANT LEVEL ADD MORE. COOLANT IN THE OVERFLOW JUG.THEN START VECHICLE AGAIN.LET ENGINE IDLE UNTIL TOP RADIATOR GET HOT.THEN THERMOSTAT WILL BE OPEN.WHILE ENGINE IDLING WATCH THE TEMPERATURE GAUGE IN VECHICLE IF TEMPERATURE GAUGE START CLIMBING IN THE HOT ZONE.TURN OFF VECHICLE LET IT SET A WHILE THEN USE LARGE RAG REMOVE OVERFLOW JUG CAP.ADD MORE COOLANT, PLACE CAP BACK ON START VECHICLE AGAIN KEEP DOING THIS PROCEDURE UNTIL TEMPERATURE STOP CLIMBING HOT ZONE.AND WHEN COOLANT LEVEL STOP DROPPING IN THE COOLANT OVERFLOW JUG.AIR IS OUT THE SYSTEM, BUT KEEP COOLANT LEVEL IN THE COOLANT OVERFLOW JUG AT THE FULL COLD MARK.DONT OVERFILL.DONT LET COOLANT OVERFLOW JUG RUN DRY IF SO AIR WILL ENTER COOLANT SYSTEM BECAUSE COOLANT LEVEL WILL BE LOW ENGINE WILL START OVERHEATING.

    Jul 24, 2011 | 2006 Dodge Grand Caravan

    2 Answers

    Having issues with a 2000 chevy impala overheating have changed the radiator and the thermostat fans seem to be working ok but overheats at idle in stop and go traffic, after a certain amount of time it...


    YOU NEED BLEED COOLANT SYSTEM.CHECK COOLANT LEVEL IN RADIATOR.ADD MORE DEXCOOL UNTIL COOLANT LEVEL IS CLOSE TO RADIATOR SPOUT.CRANK ENGINE LET IDLE UNTIL TOP RADIATOR HOSE GET HOT.WATCH TEMPERATURE GAUGE.IF TEMPERATURE GAUGE START RISING TO HOT ZONE.TURN OFF ENGINE.LET COOL DOWN.USE LARGE RAG SLOWLY OPEN RADIATOR CAP A LITTLE AT A TIME UNTIL ALL PRESSURE RELIEVED.REMOVE RADIATOR CAP.ADD MORE COOLANT.CRANK CAR AGAIN LET IDLE UNTIL TOP RADIATOR GET HOT.KEEP EYE ON TEMP.GAUGE ALSO.WHEN TEMP.GAUGE STOP CLIMBING.YOUR COOLANT SYSTEM BLED.WHEN DONE LET CAR SET A WHILE CHECK COOLANT LEVEL.ALSO FIRST THING IN THE MORNING CHECK COOLANT LEVEL AGAIN.AND BESURE ADD COOLANT IN THE OVERFLOW JUG TO THE COLD MARK.DONT OVER FILL THE COOLANT RESERVOIR JUG.WORK SAFELY DONT GET SCALDED.

    Feb 15, 2011 | 2000 Chevrolet Impala

    1 Answer

    1999 alero changed thermstat and the car will intermitantly overheat there seems to be no pattern.


    BLEED AIR OUT COOLANT SYSTEM.WAIT UNTIL ENGINE COOL DOWN.REMOVE COOLANT OVER FLOW PRESSURE CAP.IF YOU HAVE 3.1 OR 3.4 ENGINE OPEN AIR BLEED SCREW ON WATER PUMP BYPASS HOSE.OPEN BLEED SCREW.WATCH COOLANT IN OVER FLOW AS YOU OPEN BLEED SCREW COOLANT WILL DROP IN OVER FLOW JUG. AS IT DROPS CLOSE BLEED SCREW ADD MORE COOLANT IN OVER FLOW JUG DO THIS UNTIL COOLANT LEVEL STAY AT COLD FULL MARK.WHEN DONE TIGHTEN BLEED SCREW DONT OVER TIGHTEN IT OR IT WILL STRIP OUT BREAK.CRANK CAR UP UNTIL THERMOSTAT OPEN THAT WHEN TOP RADIATOR HOSE GET HOT.WATCH COOLANT GAUGE,IF ENGINE TEMPERATURE RISES TURN OFF ENGINE WAIT UNTIL COOL.REMOVE RADIATOR PRESSURE CAP USING A RAG TO KEEP FROM GETTING HANDS SCALED.ADD MORE COOLANT IF NEEDED WHEN ENGINE COOLANT STOP DROPPING IN OVER FLOW JUG AND ENGINE DONT OVER HEAT AIR IS OUT OF COOLANT SYSTEM.

    Sep 13, 2010 | 1999 Oldsmobile Alero

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    187 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Cars & Trucks Experts

    yadayada
    yadayada

    Level 3 Expert

    76846 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22246 Answers

    Randy Ohler

    Level 3 Expert

    14585 Answers

    Are you a Car and Truck Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...