Question about 2004 GMC Sierra

Open Question

I replaced the starter on 2004 GMC Sierra and now it will not start

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1118 Answers

SOURCE: Replace starter on 1992 GMC Sierra pickup truck

First thing unhook positive battery cable, unhook main cable on starter selanoid and small wire on selanoid (there may be 2 small wires) There may be a bracket on front of starter that has to be removed, and then the 2 main bolts that hold it to engine block and it should come out.

Posted on Feb 14, 2009

  • 198 Answers

SOURCE: 2004 gmc sierra rear differential

remove cover.take off back wheels and calipers (or drums).turn differential to where you see small bolt/pin (5/16) horizontally (same direction as axles)on right side of differential.remove bolt/pin.A large pin (about 5"long 3/4"diameter) should slide out differential with ease ( you may have to tap one side of the large pin).turn differential to completely remove large pin.turn differential so you can see in the view window.push each axles in (they'll go in about 1 1/2"each) You may hear one of the axle C-clips fall.If not use a small telescoping magnet to remove the C-clips from the axles through the differential window.pull each axle out about 10"so they are out of the diff.Now remove the cap bolts(4-5/8"bolts) and remove the caps(mark the caps so they go in excactly the way they came out.be careful the diff might fall out.If not you may have to use a long bar or 2x4 to wedge and pry the differential out. Have a basket/crate w/rags in it to catch the diff.TIP:If you are removing the ring gear from the diff, the bolts are left handed bolts meaning you have to turn them clockwise to loosen and counter clockwise to tighten ; )

Posted on Sep 15, 2009

Testimonial: "thank you helped ALOT perfect instructions "

  • 142 Answers

SOURCE: how to replace a starter on 1994 gmc sierra 1500

unhook the battery, there are 2 wires on the starter solenoid, 1 is a 5/16 nut and the other is a 9/16 nut remove those wires. this maybe easier to remove the heat shield first. next ther are two 9/16 bolts holding the starter in position, remove, and the starter will come out, about a 15min job

Posted on Sep 27, 2009

Molson02536
  • 3854 Answers

SOURCE: 2004 GMC Sierra 4dr truck. the fan does not work

The switch or the wire harness at the blower motor has gone bad. The highest setting 5 has no resistor, so the blower runs on high but the high current flow ends up burning up the switch's contact on that setting or the resistor wire harness at the blower motor has gone bad. Common would be the switch it self, if the switch is good. Then it's going to be the wire leads at the speed resistor by the blower motor under the glove box by the passenger leg compartment. Keep me posted, be glad to help you get your Sierra running 100% again soon.

Posted on Jan 06, 2010

  • 65 Answers

SOURCE: replacement of water pump on 2004 gmc sierra

Remove or disconnect the following:

Air outlet duct Coolant Inlet radiator hose from the water pump Upper fan shroud Cooling fan and clutch assembly Drive belt Radiator outlet hose from the coolant pump Surge tank hose Heater hose Water pump

0996b43f802030d1.jpg

DO NOT use cooling system seal tabs (or similar compounds) unless otherwise instructed. The use of cooling system seal tabs (or similar compounds) may restrict coolant flow through the passages of the cooling system or the engine components. Restricted coolant flow may cause engine overheating and/or damage to the cooling system or the engine components/assembly.

Install or connect the following:

Water pump. Install the water pump bolts. Tighten the water pump bolts first pass to 11 ft. lbs. (15 Nm); tighten the bolts final pass to 22 ft. lbs. (30 Nm). Water pump drive belt pulley and bolts (if applicable). Tighten the pulley bolts first pass to 89 inch lbs. (10 Nm); tighten the bolts final pass to 18 ft. lbs. (25 Nm). Surge tank hose Heater hose Outlet radiator hose to the coolant pump Drive belt Cooling fan and clutch assembly Upper fan shroud Inlet radiator hose to the water pump Air inlet duct Coolant

Posted on Jan 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the crankshaft sensor on a 2004 gmc sierra 4.3


behind the starter. utube has video that can help

Apr 02, 2015 | 2004 GMC Sierra

2 Answers

How do i replace a starter for a sierra gmc 96 350 engine


Disconnect the negative battery cable.
Disconnect electrical connections from starter motor
Remove two bolts securing the starter motor to the engine.
Remove starter motor
Reverse procedure to install

May 27, 2012 | 1996 GMC Sierra

1 Answer

2002 gmc 1500 sierra starter clicks but wont turn over. Have checked fuses, charged battery, tried jump starting all it does is you can here solinoid click but starter wont turn. I did turn heater fan on...


Replace the starter, the solenoid cant engage the starter because it is locked up, hence the extreme voltage drop with the fan when you try to start it with the fan on.

Oct 04, 2011 | 2002 GMC Sierra 1500HD

1 Answer

I have a 1992 gmc sierra and when I tried to start it nothing happened, I replaced the starter and now all that happens is that the starter keeps clicking. Any ideas?


did you replace the starter solenoid, it sounds like the linear motion is there in the starter, just no turn. check the solenoid

Aug 24, 2011 | 1992 GMC Sierra K1500

1 Answer

GMC Sierra Won't Start. Battery Good. Tried Jump


If you know the batter is good.

Check the Starter to see it is getting power.

Get a test light [6.00] and see if the starter will light up the test light.
If not - then you may need a new starter. From the sounds of it you might want to take it to a professional as this can be a very labor intense job because the starter has to come out the bottom.

Mar 21, 2010 | 2002 GMC Sierra

3 Answers

How to replace 2004 sierra ignition


i have a sierra also... the wheel, shifter cowl, etc. has to come off to replace the ig. switch. good luck
ps... did you try putting the shifter in neutral and try to start it? there is a safety switch so that when it is in gear and running, so that the starter cannot be engaged..its best to have it checked out at a garage. bye...

Nov 09, 2009 | 2004 GMC Sierra 2500

1 Answer

Replaced battery and starter both where bad. Truck


loose connections and starter relay in power distribution box under hood. Make sure you dont have a loose or poor connection on a ground or power wire from battery.

Oct 27, 2009 | 1997 GMC Sierra

1 Answer

RAN OUT OF GAS WILL NOT START AFTER FILLING UP.


Disconnect the battery and leave for 30mins then replace the battery leads then try.

Jun 11, 2009 | 2004 GMC Sierra Denali

1 Answer

Replace starter on 1992 GMC Sierra pickup truck


First thing unhook positive battery cable, unhook main cable on starter selanoid and small wire on selanoid (there may be 2 small wires) There may be a bracket on front of starter that has to be removed, and then the 2 main bolts that hold it to engine block and it should come out.

Feb 14, 2009 | 1992 GMC Sierra

Not finding what you are looking for?
2004 GMC Sierra Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...