Question about Cars & Trucks

Open Question

2006 dodge durango p0158

Need to know if it left or right side position two sensor

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 82 Answers

SOURCE: 2001 dodge durango v8 4.7

It is acually called the vehicle speed sensor I do believe. It should should be located on the top of your transmission with a wiring harness attached to it. It should also have 1 bolt holding it in also. Whatever you do, do not rotate the gear when you remove it. Try to mark the exact way it came out when you replace the sensor. When you pull the sensor out it will have this gear attached to it which will need to be placed into the new sensor and put back into the vehicle in the same way it came out or you will throw a code and it will not be pretty. Good luck, hopefully I didn't scare you it can be a simple repair just mind your P's and Q's.

Posted on Jan 07, 2009

Ad
  • 245 Answers

SOURCE: location of speed sensor for a 2003 dodge durango

the speed sensor for this vehicle is actually in the rear differential of the vehicle. this is the sensor that runs the speedometer also known as the vehicle speed sensor. there are also two speed sensors in the front one on each wheel known as wheel speed sensors these are for the abs system only

Posted on May 17, 2009

emissionwiz
  • 76164 Answers

SOURCE: knock sensor dont work for 2005 dodge durango

this problem is very seldom the knock sensor, it can be the harness connector at the sensor or the engine has excessive knock which will set a code, u did not mention the particular code so hard to say, the location of the knock sensor is the lower section of the engine block, it is screwed into what would normally be a block drain plug, if u replace it u need to torque it to whatever the factory spec is or it can cause it throw another code..

Posted on May 29, 2009

motor1258
  • 6674 Answers

SOURCE: 2006 dodge durango 5.7 limited. engine light

Sounds right & check manual for warranty guidelines for your emission system & components, sometimes they are a little longer than 40,000 I believe.

Posted on Jun 04, 2009

lester482529
  • 226 Answers

SOURCE: My 1999 Dodge Grand Caravan left rear powered vent isn't working.

IF YOUR TALKING ABOUT THE POWER VENT WINDOW.IT MAY BE HYPER EXTENDED LIKE A KNEE OR ELBOW.TRY TAKING A SCREWDRIVER FROM THE OUTSIDE AND PUSHING THE HINGE INWARD JUST ENOUGH TO LET THE MOTOR WORK IT CLOSED.IF THE MOTOR ITSELF ISN'T WORKING PUSH THE HINGE JUST PAST CENTER THEN USE YOUR HAND TO CLOSE THE WINDOW PUSHING IT CLOSED WERE THE MOUNT IS UNTIL YOU CAN GET A NEW MOTOR.HOPE THIS HELPS

Posted on Jul 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Knock sensor location on a 2005 dodge Durango 4.7 liter


There are two knock sensors, and they are installed into the block (left and right side) under the intake manifold. The intake manifold must be removed to replace them. They are not identical, and must be installed in the correct position (they are tagged) so that the PCM knows which is which.

Jan 09, 2016 | Dodge Cars & Trucks

1 Answer

I have 2 codes showing for my 2006 dodge Durango the codes r p0158 and p0058 what that mean


Code 158 is for high voltage in the O2 sensor circuit for bank two sensor two. This is the sensor after the cat converter.
Code 58 is for the same problem with the heater circuit in the same sensor. My guess would be the sensor has shorted out internally, or you have a wiring problem between the sensor and the engine computer. The circuits would need to be tested.

Sep 03, 2015 | Dodge Cars & Trucks

1 Answer

2001 Dodge Durango chrankshaft sensor position


If you have a 4.7L V-8 the sensor is located on the passenger side(near the rear) of the engine block . If its a 5.9L V-8 its located on passenger side between transmission and engine block (behind the cylinder head)

Jul 07, 2014 | 2001 Dodge Durango

1 Answer

Where is the oil presser sensor located at on a 2005 dodge durango


The oil pressure sensor for the 4.7 screws into the block right next to oil filter which is on the front left side of the engine.

Jun 27, 2014 | Cars & Trucks

2 Answers

2001 dodge durango downstream oxygen sensors the same left and right


No, the oxygen (O2) sensors are slightly different. Chrysler/Dodge issues different part numbers for each downstream position & so do the aftermarket parts suppliers. If you're going to buy aftermarket O2 sensors, I strongly recommend that you avoid buying "universal", go for the OE style direct fit.

You'll need to know if your Durango is equipped with California emissions before you shop for O2 sensors. Call the parts dept at your local Dodge dealer, feed them your VIN; based on the VIN, they'll be able to tell you if your Durango is equipped with CA emissions and then you can shop accordingly.

May 25, 2014 | 2001 Dodge Durango

1 Answer

Had code p0058 come up, so i replaced the co2 sensor. After a few days engine light came on with code p0158....which appears to be almost the same code. whats causing p0158 if ive already changed the...


This vehicle is equiped with 2 O2 sensors 1 is before the Cat converter and 1 after the Cat converter this code is for the 1 after the Cat converter or the most rear sensor not the first 1 change the farthest one from the engine and your problem should be solved.

Apr 29, 2011 | 2004 Dodge Durango

1 Answer

The security alarm goes off any time a door is opened, do you know how to reset? 2006 dodge durango


i beleive its controled by the drivers door lock put key in door and turn twice to the right or left that should reset it

Jul 22, 2010 | 2006 Dodge Durango

1 Answer

2000 Dodge Durango-what is TPS? I have a lot of problems with my truck not staying on and my dash says "No BUS"


the tps stands fo throttle position sensor and its located on left side of the engine on the throttle body.

Jan 07, 2010 | 2000 Dodge Durango

2 Answers

Check engine light on dodge durango


Hi,
I Found a solution for this problem.
the code is P0344.
Camshaft Position Sensor `A` Circuit Intermittent (Bank 1 or Single Sensor)
I Got this sensor at Autozone for $ 25,99.
Hope this help.
My car-2006 Dodge durango V8 4.7 sxt

Jul 02, 2008 | 2006 Dodge Durango

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...