Question about 2000 Chevrolet Blazer

1 Answer

How to diconect the brake cable handle to take out the dash board

I need to replace my heater core and to do that i need to remove the dash board with an emergency cable in the way(going thru dash board)

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 87 Answers

I am assuming you mean the release lever, it just slides out of a c channel on the pedal assembly then fish the cable end out of the lever and it should pull right out

Posted on Jan 15, 2013

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 3 Answers

SOURCE: Removing dash board on 2001

e emergency brake cable has to be removed at the pedal on the kick panel and not at the dash pay attention on removal and repeat steps to reinstall as it can be slid in from the front of the dash for new install but has to be removed in reverse steps

Posted on Mar 03, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Heater core 2004 chrysler pacifica replace


  1. Remove the silencer boot fasteners located around the base of the lower steering shaft from the dash panel so that it may be pushed aside.
  2. Remove the brake lamp switch from its mounting bracket.
  3. Disconnect the power brake booster input rod (push rod) from the pin on the brake pedal arm.
  4. If equipped with power adjustable pedals, remove the adjustable pedal assembly.
Note: Take the proper precautions to protect the carpeting below the heater core from spilled engine coolant and have absorbent toweling readily available to clean up any spills.

  1. Remove the heater core tubes.
  2. Remove the two screws that secure the heater core mounting plate to the HVAC air distribution
    1. If NOT equipped with power adjustable pedals, pull the accelerator pedal upward and push the brake pedal downward for clearance to remove the heater core from the air distribution housing.
    2. Remove the heater core by carefully pulling it straight out of the side of the air distribution housing.
    Installation

    1. If NOT equipped with power adjustable pedals, pull the accelerator pedal upward and push the brake pedal downward for clearance to install the heater core into the HVAC air distribution housing.
    2. Install the heater core by carefully pushing it straight into the side of the air distribution housing.
    3. Install the two screws that secure the heater core to the air distribution housing. Tighten the screws to 2 Nm ( 17 in lbs ) .
    4. Install the heater core tubes.
    5. If equipped with power adjustable pedals, install the adjustable pedal assembly.
    6. Connect the power brake booster input rod to the pin on the brake pedal arm.
    7. Install a new brake lamp switch.
    8. Install the silencer boot around the base of the lower steering shaft on the dash panel.
    9. Reconnect the negative battery cable.
    10. If the heater core is being replaced, flush the cooling system.
    11. Refill the engine cooling system.
    housing.

Nov 01, 2011 | 2004 Chrysler Pacifica

1 Answer

Replacing heater core chryler picifica


  1. Remove the silencer boot fasteners located around the base of the lower steering shaft from the dash panel so that it may be pushed aside.
  2. Remove the brake lamp switch from its mounting bracket.
  3. Disconnect the power brake booster input rod (push rod) from the pin on the brake pedal arm.
  4. If equipped with power adjustable pedals, remove the adjustable pedal assembly.
Note: Take the proper precautions to protect the carpeting below the heater core from spilled engine coolant and have absorbent toweling readily available to clean up any spills.

  1. Remove the heater core tubes.
  2. Remove the two screws that secure the heater core mounting plate to the HVAC air distribution
    1. If NOT equipped with power adjustable pedals, pull the accelerator pedal upward and push the brake pedal downward for clearance to remove the heater core from the air distribution housing.
    2. Remove the heater core by carefully pulling it straight out of the side of the air distribution housing.
    Installation

    1. If NOT equipped with power adjustable pedals, pull the accelerator pedal upward and push the brake pedal downward for clearance to install the heater core into the HVAC air distribution housing.
    2. Install the heater core by carefully pushing it straight into the side of the air distribution housing.
    3. Install the two screws that secure the heater core to the air distribution housing. Tighten the screws to 2 Nm ( 17 in lbs ) .
    4. Install the heater core tubes.
    5. If equipped with power adjustable pedals, install the adjustable pedal assembly.
    6. Connect the power brake booster input rod to the pin on the brake pedal arm.
    7. Install a new brake lamp switch.
    8. Install the silencer boot around the base of the lower steering shaft on the dash panel.
    9. Reconnect the negative battery cable.
    10. If the heater core is being replaced, flush the cooling system.
    11. Refill the engine cooling system.
    housing.

Oct 18, 2011 | 2004 Chrysler Pacifica

2 Answers

I need to get directions of how to remove the heater core from a 2003 pontiac aztek thank u


the hearer core is inside underneath the dash board is a pretty tight spot

Aug 10, 2011 | 2003 Pontiac Aztek

1 Answer

Removing dash board on 2001 Chevy Blazer to replace heater core. having problems with removing emergency brake cable.


e emergency brake cable has to be removed at the pedal on the kick panel and not at the dash pay attention on removal and repeat steps to reinstall as it can be slid in from the front of the dash for new install but has to be removed in reverse steps

Feb 27, 2011 | 2000 Chevrolet Blazer

1 Answer

Removing heater core


This is for a 2.3L
Hope this helps, it it does please leave feedback Thank You and Good Luck

REMOVAL
  1. Disconnect battery ground cable.
  2. Drain cooling system.
  3. Raise and support vehicle.
  4. Disconnect heater hoses from heater core assembly.
  5. Remove drain tube.
  6. Lower vehicle.
  7. If equipped, remove console as follows:
    1. Apply parking brake and block drive wheels.
    2. Position transaxle shift lever in Neutral.
    3. On models with automatic transaxle, remove clip retaining shift lever handle to lever, then remove shift lever handle.
    4. On models with manual transaxle, turn shift lever handle counterclockwise to remove from lever.
    5. On all models, carefully pry upward on outer edges of console trim plate.
    6. Disconnect electrical connectors and ashtray lamp from console trim plate, then remove trim plate from console.
    7. Remove console to mounting bracket attaching screws, then remove console.
  1. Right and left sound insulators.
  2. Steering column opening filler.
Floor Air Duct Outlet 58917672

  1. Floor air outlet duct.
  2. Heater core cover.
  3. Heater core mounting clamps and remove heater core.
INSTALLATION
  1. Heater core and heater core mounting clamps.
  2. Heater core cover.
  3. Floor air outlet duct.
  4. Right and left sound insulators.
  5. Console.
  6. Steering column opening filler.
  7. Raise vehicle.
  8. Heater hoses to heater core.
  9. Drain tube to heater case.
  10. Lower vehicle.
  11. Negative battery cable.
  12. Fill cooling system and check for leaks.

Jan 01, 2011 | 1994 Pontiac Grand Am

2 Answers

How do i change heater core in 1999 dodge caravan?


Big job.
Remove the dash. The heater-core is behind the center console.

Oct 25, 2009 | 1999 Dodge Grand Caravan

1 Answer

How to Replace a Heater Core


Removal & Installation

  1. Disconnect the negative battery cable.
    CAUTION After disconnecting the negative battery cable, wait 2 minutes for the driver-s/passenger-s air bag system capacitor to discharge before attempting to do any work around the steering column or instrument
  2. On diesel models, remove the passenger side battery and battery tray.
  3. Remove the instrument panel by performing the following procedures:
    1. Remove the air bag control module (ACM) and bracket from the floor panel tunnel.
    2. Remove the trim from both cowl side inner panels.
    3. Remove the steering column-to-instrument panel opening cover.
    4. Remove the 2 hood latch release handle-to-instrument panel lower reinforcement screws and lower the handle to the floor.
    5. Disconnect the driver-s side air bag module wiring harness connector from the lower instrument panel reinforcement.
    6. Place the wheels in the straight-ahead position and lock the steering wheel. Remove the steering column without disassembling it.
    7. From under the driver-s side of the instrument, disconnect or remove the following items:

      Parking brake release handle linkage rod from the parking brake mechanism located on the left cowl side inner panel. Instrument panel wiring harness connector from the parking brake switch located on the parking brake mechanism. Three wiring harness connectors (body wiring harness, headlight, dash) from the 3 junction block connector receptacles located closest to the dash panel. Head light/dash-to-instrument panel bulkhead wiring harness connector screw and disconnect the connector. Instrument panel-to-door wiring harness connector located directly below the bulkhead wiring harness connector. Infinity sound system wiring harness connector (if equipped), located at the outboard side of the instrument panel bulkhead connector. Stop light switch electrical connector. Vacuum harness connector located near the left side of the heater/air conditioning housing.
    8. Under the passenger-s side of the instrument panel, disconnect the radio antenna coaxial cable connector.
    9. Loosen both sides of the instrument panel cowl side roll-down bracket screws about 1 / 2 inch (13mm).
    10. Remove the 5 upper instrument panel-to-upper dash panel screws; remove the center screw last.
    11. Roll down the instrument panel and install a temporary hook in the center hole on top of the panel. Attach the other end to the center hole in the top of the dash panel. The opening should be approximately 18 inches (46cm).
    12. Disconnect the instrument panel-to-heater/air conditioning housing assembly wiring harness connectors.
    13. Using an assistant, remove the instrument panel from the vehicle.

  4. If equipped with air conditioning, perform the following procedure:
    1. Discharge and recover the air conditioning system refrigerant.
    2. Disconnect the refrigerant lines from the evaporator. Plug the openings to prevent contamination.
    3. Disconnect the refrigerant lines from the accumulator. Plug the openings to prevent contamination.
    4. Remove the accumulator.

  5. Drain the cooling system into a clean container for reuse.
  6. Disconnect the heater hoses from the heater core tubes.
  7. Remove the PCM from the dash panel and move it aside. Do not disconnect the PCM harness connector.
  8. In the engine compartment, remove the heater/air conditioning housing assembly-to-chassis nuts.
  9. In the passenger-s compartment, remove the heater/air conditioning housing-to-dash panel nuts.
  10. Pull the heater/air conditioning housing assembly rearward far enough to clear the studs and air conditioning drain tube holes.
  11. Remove the heater/air conditioning housing assembly from the vehicle.
  12. Remove the upper-to-lower heater/air conditioning housing screws and remove the upper housing.
  13. Remove the heater core from the lower housing.


    Fig. View of the heater/air conditioning housing assembly


    0900c15280225dc3.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. View of the heater core

Apr 07, 2009 | 1997 Dodge Ram

1 Answer

86 IROC heater core


Removal & Installation
1.Disconnect negative battery cable. Drain cooling system. Disconnect heater hoses from heater core, and plug openings. Detach hood release cable. Remove both dash side panels. Remove left and right lower dash trim panels. Remove glove box. Remove 7 screws securing center accessory console. Disconnect wires on accessory console, and remove accessory console. Remove control cables at heater case.

2.Remove 4 bolts securing steering column to instrument panel. Lower steering column. Remove 2 bolts from instrument panel mounts at far left and right sides of instrument panel. Remove defroster duct trim on top of dash. Remove instrument cluster screws. Pull instrument cluster out slightly. Disconnect electrical connections and speedometer cable from instrument cluster. Remove instrument cluster.

3.Disconnect all electrical connectors from instrument panel. Remove parking brake console. Remove glove box. Remove bolts securing instrument panel support to floorpan. Remove all instrument panel mounting bolts. Remove instrument panel.

4.Separate heater case from blower. Remove 3 nuts and pull heater

Dec 06, 2008 | 1986 Chevrolet Camaro

2 Answers

How to replace heater core on a 1989 Chev. 1500 (350)


Start by draining the coolant, disconnect dash board wiring harness from pcm behind kick panels, disconnect eye shaft, unbolt dashboard and remove dash. (Remember to tape steering wheel in place as it might have a clock spring). You might have to remove some trim panel on top of dash or cluster from dashboard to gain access to retaing bolts, disconnect heater hoses from heater core in engine compartment and remove heater core, reverse install.

Dec 02, 2008 | 2003 Chevrolet Suburban 1500

Not finding what you are looking for?
2000 Chevrolet Blazer Logo

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...