Question about Cars & Trucks

1 Answer

Car was running fine until I stopped at a stop light yesterday. Since then, doesn't want to run when in gear, only in park.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Sounds like a furl filter problem. Check online for the make /model in auto repair manuals to find the type and location of the fuel filter. Some are in the tank---HARD TO FIX yourself.- some are inline (in the fuel line) they are easy to replace yourself.

Posted on Jan 14, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why the transmissiom won' engage in any gear


Transmission won't engage Drive or Reverse - EricTheCarGuy

www.ericthecarguy.com/.../53999-transmission-won-t-engage-drive-or-r...
This transmission shifted smooth and strong through all gears until today when it stopped all of ... Any idea on where we should start tackling this issue? .... Also, make sure that the pressure tester is not leaking or you will run the tranny dry(use ...

Gear shifter goes from park to drive with no effect. Won't ...


Nov 26, 2015 | Cars & Trucks

1 Answer

Code P0736, P0731, P0720, P0700


Well code 700 is a generic code that means there is a problem with the transmission or the control module.
Code 736 is an incorrect gear ratio for reverse, code 731 is incorrect ratio in first gear, and 720 is the code for the speed sensor which involves the engine computer as well as the speedo.
Its possible the speed sensor is causing the other codes.
I would have a shop check the speed sensor circuit, clear the codes, and see how many come back then proceed with more testing as needed.

Jul 29, 2013 | Chrysler Cars & Trucks

1 Answer

Engine is sputtering when I stop and the idling is below 1000 rpm.


SOUNDS LIKE A VACUM LEAK OR A HOLE IN YOU AIR INDUCTION TUBE ( BIG BLACK FLEX PIPE) BETWEEN MASS AIR FLOW SENSOR AND MOTOR

Dec 09, 2011 | 1995 Toyota Camry

1 Answer

MY 2001 FOCUS SE THE REAR STOP LIGHT STAY ON EVEN WITH THE BRAKE PEDAL RELEASED WHEN I SHIFT IT INTO PARK POSITION THE STOP LIGHTS GO OFF THIS IS WITH THE ENGINE IN THE ON/RUN POSITION? REPLACED THE STOP...


are you sure you're not looking at the running lights? the running lights on the rear and the daytime running lights on the front are suppose to come on when the car is in gear and go out when the car is in park.

Aug 16, 2011 | 2008 Ford Focus SE Sedan

2 Answers

I have a 92 caprice and it makes a buzzing noise when in drive and reverse. When I put it in park the buzzing stops. What could this be?


The noise is from your transmission.
Run the car until it's hot. On a level surface take the tranmission through the gears PRNDL and back again into Park. Check the level of transmission fluid with the car running. Top it off to where the lvel is between the ADD and FULL marks. DO NOT overfill.
If the level is good or topping it of doesn't fix it you'll need to have the transmission checked

Jul 20, 2011 | 1992 Chevrolet Caprice

1 Answer

I have a 1997 Town Car and it runs perfectly fine until i park it, then try to start it and put it in gear, it will start up just fine with no noises, and the battery, lights, and everything else is fine,...


Check to see if your brake lights come on when the brake pedal is depressed. If they do not come on, the problem could be the brake light switch or associated connector/wiring. The brake light circuit controls the solenoid (control) that allows the shifter to come out of the park position. The brake light switch is connected to the brake pedal arm. You May have to remove a cover panel (three plactic retainers) to see the switch. A possible solution is to turn the ignition key to the 1st position, then shift the car into neutral. This should allow you to start the car and shift into any gear. HOWEVER, you may not have brake lights (use hand signals) and when you park, use the emergency brake after stopping, shif the car to neutral and not PARK. This will allow use of your car until you can get it properly fixed.

Aug 27, 2010 | 1997 Lincoln Town Car

1 Answer

Rough idle then stalls


Vacume leak or bad idle motor. With the car in park and running with the hood open listen for leaks moving your hand around the different hoses looking for a change in the sounds that you hear. The idel motor also makes the car idel up to 1500 RPM or so right at start-up then idel down, If it doesn;t the idel motor is likly. Check engine light is on when running? Test for codes, Follow code test charts don't skip any steps!.

Nov 02, 2009 | 1998 Chevrolet Malibu

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

62 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...