Question about 1993 Cadillac Fleetwood
ALL THE LIGHTS WORK FINE JUST DOME LIGTES TAKE TOO LONG TO TURN OFF AND IT`S KILLING MY BATTERY JUST PUT NEW BATTERY IN AND HAVE TO DISCONNECT EVERY TIME I TURN OFF MY CAR PLEASE HELP
There are two relays that keep accessory power on after you turn the key off and close the door. One of them may be stuck on.
You may need a shop manual to find and test them.
Posted on Jan 14, 2013
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
well first off, check the glove box light blub, make sure it shuts off when you close the door, check it by pressing the switch with your finger to make sure it shuts off, also check under the hood for the light there if there is one, pull the bulb, and the same thing for any bulb in the trunk, then check again after a day to see if the battery dies, if it is dying while the vehicle is not running then it is the battery, if it is dying after it is running then it is the alt. you can check that also tho with a multimeter set to the DC volts setting, place the black end <the ground to any grounded area> and the red end <the hot lead to the back of the alt. > it should be reading higher then 12 volts, normally should be a higher reading then 12 volts... if you are getting a lower reading or just 12 volts then the alt. is bad and needs to be replaced...hope this helps you out...
Posted on Jun 15, 2009
Tips for a great answer:
The liftgate lamps
The courtesy lamp supply voltage circuit of the body control module (BCM) supplies battery positive voltage to the dome lamp, the liftgate lamps, and the map lamps. When any door is opened, the door jamb switch contacts close providing a door open input to the BCM. The BCM then provides a ground to the interior lamps with the switch in the AUTO position. The interior lamps receive a ground at G401 with the switch in the ON position.
Important: If the liftgate is opened after all the modules go to sleep, the dome light will not come on. The liftgate ajar switch input to the BCM will not wake up the BCM once it has gone to sleep, so the dome light will not come on. Once the BCM gets an input to wake it up, from remote keyless entry (RKE) or a door handle, the dome light will turn on when the liftgate is opened.
If the driver inadvertently leaves any interior lamp ON, the BCM will turn it OFF after a 20 minute time-out.
The courtesy lamps will turn OFF immediately if the ignition switch is turned to the ON position or approximately 20 seconds after all doors are closed.
The courtesy lamps are controlled by the body control module (BCM). Inputs from the dome lamp switch and the door ajar switches are monitored by the BCM. When a door ajar switch is closed, or the dome lamp switch is turned to the ON position, the BCM supplies the B+ for the courtesy lamps.
With out a factory Tech2 scan tool or equivalent an knowing how these systems work ,you best bet is to take your vehicle to the dealer or some other ASE certified repair shop !
Sep 04, 2015 | 2009 Buick Enclave
Apr 14, 2015 | 2000 Nissan Quest
Dec 17, 2014 | 2005 Toyota Matrix
Apr 28, 2017 | 1998 Mercury Sable
Aug 24, 2011 | 1992 Buick Skylark
Jan 21, 2010 | 1983 GMC C3500
Sep 02, 2009 | 1991 Oldsmobile Cutlass Ciera
Aug 19, 2009 | 2003 Jeep Grand Cherokee
May 04, 2009 | 2006 Chevrolet Impala
72 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: