Question about Toyota Highlander

Open Question

Toyota highlander power liftgate does not fully open

The liftgate on my highlander does not fully open to the top. It only opens up about 85% of the way. adding wd40 did not help.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 2005 Tahoe Rear liftgate will

Doors unlock on 2005 Chevy Taho but the rear hatch won't. It does not even click when you press button. It does not have a key acess. Is there a manuel opener?? Or a fuse. Even the glass hatch will not unlock.

Posted on Sep 16, 2008

Ad
  • 62 Answers

SOURCE: 2003 Saturn Vue rear liftgate won't open

The easy part is you just need the latch for the liftgate. The hard part is getting to it and opening the liftgate to replace the latch. You should be able to pull the liftgate trim off most of the way with the gate closed and try to manually actuate the latch to open the gate. You may have to go so far as breaking the latch from the inside to open the gate and then replace your latch.

Posted on Dec 17, 2008

  • 3 Answers

SOURCE: power liftgate doesn't work

The power liftgate motor is located on the driver side panel directly behind the lift arm. First you will have to take the safety belt bolt out. After you get the plastic piece free from the body you will have to take the bolt out of the arm that connects to the hatch. Make sure you have a big enough torx bit for the bolt that holds the arm to the gate. This will allow you to slide the plastic piece off and out of your way. If you are having trouble getting the plastic piece to come off from around the liftgate arm, try putting the door down, that helped me. The rest should be easy. Hope this info helped you out. 

Posted on Apr 14, 2009

emissionwiz
  • 80407 Answers

SOURCE: code p1135 what wrong help,toyota 2000,highlander

That code is specific to the Air-Fuel Ratio (A/F) Sensor Heater Circuit Malfunction (Bank 1 Sensor 1)

P1135 Trouble Area:
 Open or short in A/F sensor (bank 1, sensor 1)
 A/F sensor (bank 1, sensor 1) heater
 ECM __________________

Posted on Jun 17, 2009

  • 14 Answers

SOURCE: 2001 T & C power liftgate will not open.

try this out. this might help. I am still looking for a solution as well. the shims mentioned here dont seem to work for me. the latch will not disengage and everything stops. http://chryslerforum.com/forum/showthread.php?t=4534&highlight=2001+liftgate

Posted on Sep 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

06 Lincoln Navigator liftgate opens okay but need help to close why?


Power Liftgate
The power liftgate feature will allow the customer to automatically OPEN or CLOSE the liftgate by activating the interior open/close switch, the remote keyless entry transmitter or by manually initiating liftgate movement. The power liftgate uses a power cinch system to latch the liftgate.
The power liftgate system consists of the following:
  • Power liftgate control switch (located in the overhead console)
  • Power liftgate motors (located in the rear headliner area)
  • Optical sensor and power liftgate encoder wheel (located in the left power liftgate motor assembly)
  • Pinch strip switches (located on the body by the liftgate)
  • Home position switch (located on the cinch actuator)
  • Forkbolt switch (located on the cinching latch assembly)
  • Detent switch (located on the cinching latch assembly)
  • Liftgate close chime module (located in a unit external from the power liftgate module)
  • There are a lot of electrical switches an motors
  • Visual Inspection Chart Mechanical Electrical
    • Power liftgate motors
    • Power cinching latch and linkage
    • Power liftgate pinch strip switches
    • Liftgate and liftgate hinges
    • Liftgate assist cylinders
    • Liftgate strikers
    • Exterior release handle and linkage
    • Liftgate weatherstrip
    • Liftgate alignment to body and striker
    • Central junction box (CJB) fuse:
      • 5 (7.5A)
      • 105 (30A)
    • Power liftgate control switch
    • Wiring harness
    • Connectors
    Are you willing to take the back hatch apart to test this ,to find a fix . But first have it check for DTC'S - diagnostic troulbe codes '
  • Power Liftgate Module Diagnostic Trouble Code (DTC) Index
    Power Liftgate Module Diagnostic Trouble Code (DTC) Index DTC Description Source Action B1342 ECU Is Defective Power Liftgate Module INSTALL a new power liftgate module. REFER to Power Liftgate Module in this section. B2477 Module Configuration Failure Power Liftgate Module REFER to Section 418-01 . B2522 Vbatt1 Circuit Failure Power Liftgate Module Go To Pinpoint Test B . B2552 Vbatt2 Circuit Open Power Liftgate Module Go To Pinpoint Test B . B2698 Vbatt2 Circuit Failure Power Liftgate Module Go To Pinpoint Test B . B2699 Left Pinch Strip Open or Short to Battery Power Liftgate Module Go To Pinpoint Test B . B2700 Right Pinch Strip Open or Short to Battery Power Liftgate Module Go To Pinpoint Test B . B2701 Left Pinch Strip Stuck Active Power Liftgate Module Go To Pinpoint Test B . B2702 Right Pinch Strip Stuck Active Power Liftgate Module Go To Pinpoint Test B . B2703 Open/Close Switch Stuck Active Power Liftgate Module Go To Pinpoint Test B . B2704 Optical Sensor Power Short to Ground Power Liftgate Module Go To Pinpoint Test B . B2705 Optical Sensor 1 Input Not Active During Powered Gate Movement Power Liftgate Module Go To Pinpoint Test B . B2706 Optical Sensor 2 Input Not Active During Powered Gate Movement Power Liftgate Module Go To Pinpoint Test B . B2709 Gate Open Output Short to Battery Power Liftgate Module Go To Pinpoint Test B . B2710 Gate Close Output Short to Battery Power Liftgate Module Go To Pinpoint Test B . B2711 Gate Open Output Short to Ground or Open Power Liftgate Module Go To Pinpoint Test B . B2712 Gate Close Output Short to Ground or Open Power Liftgate Module Go To Pinpoint Test B . B2713 Unlatch Output Short to Ground or Open Power Liftgate Module Go To Pinpoint Test B . B2714 Uncinch Output Short to Ground or Open Power Liftgate Module Go To Pinpoint Test B . B2715 Cinch Output Short to Ground or Open Power Liftgate Module Go To Pinpoint Test B . B2718 Gate Ajar Output Short to Battery Power Liftgate Module Go To Pinpoint Test B . B2721 Gate Ajar Output Short to Ground or Open Power Liftgate Module Go To Pinpoint Test B . B2722 Open/Close Switch Active During Self-Test Power Liftgate Module Go To Pinpoint Test B . B2723 Glass Position Switch Active During Self-Test Power Liftgate Module Go To Pinpoint Test B . B2724 Forkbolt Switch Invalid During Self-Test Power Liftgate Module Go To Pinpoint Test B . B2725 Detent Switch Invalid During Self-Test Power Liftgate Module Go To Pinpoint Test B . B2726 Home Switch Invalid During Self-Test Power Liftgate Module Go To Pinpoint Test B . B2819 Gate Motor Circuit Short to Battery Power Liftgate Module Go To Pinpoint Test B . B2820 Gate Motor Circuit Short to Ground or Open Power Liftgate Module Go To Pinpoint Test B . B2821 Cincher Motor/Unlatch Actuator Short to Ground or Open Power Liftgate Module Go To Pinpoint Test B . B2822 Cincher Motor/Unlatch Actuator Short to Battery Power Liftgate Module Go To Pinpoint Test B . B2825 Movement Ceased Due to Excess Speed Deviation Power Liftgate Module Go To Pinpoint Test B . B2903 Chime Output Circuit Short to Battery Power Liftgate Module/ Liftgate Chime Module Go To Pinpoint Test C . C1935 Chime Circuit Failure Power Liftgate Module/ Liftgate Chime Module Go To Pinpoint Test C . U1950 UBP Communication BUS Fault UBP Communi- cation REFER to Section 418-00 . U2338 Invalid ACM Message Data Power Liftgate Module REFER to Section 418-00 . U2242 Invalid 4WAS Message Data 4WAS Module REFER to Section 308-07A . U2403 Invalid CSM Message Data Vehicle Security Module REFER to Section 418-00 . U2406 Invalid IC Message Data Instrument Cluster Module REFER to Section 413-01 . U2469 Power Liftgate Disabled By Customer Interface Instrument Cluster Module Turn power liftgate on at message center. U2470 Unexpected Keyfob/Keypad Button Press Power Liftgate Module Go To Pinpoint Test A . U2471 Unexpected PRNDL State Power Liftgate Module REFER to Section 419-10 . U2472 Unexpected IGN State Power Liftgate Module REFER to Section 418-00 . U2473 Unexpected Vehicle Speed Instrument Cluster Module/ Powertrain Control Module REFER to Section 413-01 . U2528 PRNDL Data Mismatch Power Liftgate Module/ Instrument Cluster Module Go To Pinpoint Test D .

Feb 13, 2017 | 2006 Lincoln Navigator 4x4

3 Answers

Does anyone have any suggestions? I don't have a garage to put it in so I need to find a way to get it closed. Please help!


How to Use the Power Liftgate on 2013 Toyota RAV4

www.autoevolution.com/.../how-to-use-the-power-liftgate-on-2013-toyo...
Nov 13, 2013 - First, there is no more spare tire attached to the rear door and second...... How to Use the Power Liftgate on 2013 Toyota RAV4 ... angle, press one of the two buttons again; Press and hold one of the buttons to close the hatch.

2013 Toyota Rav4 Power liftgate not working when pressing ...

? 0:46
https://www.youtube.com/watch?v=X-VjbRatwY4
Apr 28, 2014 - Uploaded by Adam Bednarz
2013 Toyota Rav4 Power liftgate not working or opening by itself when ... operation and you then have to manually open and close the door. .... Got the car back from the 30K service and the back hatch was not working.

How do I operate my 2013 RAV4 adjustable power liftgate?

toyota.custhelp.com/.../detail/.../how-do-i-operate-my-2013-rav4-adjusta...
The adjustable power liftgate can be opened and closed using either a switch on the ...The PWR DOOR OFF switch in the glove box must be in the 'operate' ... To open the liftgate using the Smart Key, press and hold the rear liftgate ... To open the liftgate using the switch on the door itself (located below the Toyota logo and ...

XLE trunk release - Toyota RAV4 Forums - RAV4World.com

www.rav4world.com > ... > 4.4 Interior

Jul 29, 2013 - 10 posts - ‎5 authors
There is an inside emergency release for the trunk, liftgate, back door, hatch, whatever you ... This is from page 128 of the 2013 user's manual: ... Very bad experience with power rear hatch and Toyota ...
10 posts
Jan 1, 2014
Power Rear Hatch fails to close
9 posts
Sep 25, 2013
Rear hatch problems
10 posts
Jun 27, 2013
Backdoor (liftgate) won't close
3 posts
Mar 9, 2013
More results from www.rav4world.com

Jan 11, 2016 | 2013 Toyota RAV4

1 Answer

Very cold outside, we used the hatchback all day; but now we can't get it to close. We did try using the button in the glove box - still won't close


How to Use the Power Liftgate on 2013 Toyota RAV4

www.autoevolution.com/.../how-to-use-the-power-liftgate-on-2013-toyo...
Nov 13, 2013 - First, there is no more spare tire attached to the rear door and second...... How to Use the Power Liftgate on 2013 Toyota RAV4 ... angle, press one of the two buttons again; Press and hold one of the buttons to close the hatch.

2013 Toyota Rav4 Power liftgate not working when pressing ...

? 0:46
https://www.youtube.com/watch?v=X-VjbRatwY4
Apr 28, 2014 - Uploaded by Adam Bednarz
2013 Toyota Rav4 Power liftgate not working or opening by itself when ... operation and you then have to manually open and close the door. .... Got the car back from the 30K service and the back hatch was not working.

How do I operate my 2013 RAV4 adjustable power liftgate?

toyota.custhelp.com/.../detail/.../how-do-i-operate-my-2013-rav4-adjusta...
The adjustable power liftgate can be opened and closed using either a switch on the ...

Jan 11, 2016 | 2013 Toyota RAV4

1 Answer

How do I reset lift gate on 2004 lincoln navigator. It doesn't open or close anymore with the remote


Maybe your key fob needs a new battery !
Power Liftgate Initialization

NOTE:If the power liftgate system is turned OFF in the message center, the system cannot be activated with any switches or with the liftgate handle. The system will need to be turned ON for any power operation to occur.

NOTE:The power liftgate may not operate under the following conditions:

  • a low voltage or dead battery.
  • a disconnected battery
  • a power liftgate that has been left open for more than six hours.
  • a power liftgate that has been manually closed and left ajar.
If any of these conditions has occurred, the power liftgate must be reset.
  1. Manually close and fully latch the power liftgate.
  1. NOTE:If the power liftgate does not open during this step, refer to the symptom chart to diagnose the power liftgate for no operation.
    Power open the power liftgate by using the keyfob or overhead console switch.
  1. Once the power liftgate is fully open, close the power liftgate by using the keyfob or overhead console switch.
    This system can also set DTC'S
  2. POWER LIFTGATE MODULE DIAGNOSTIC TROUBLE CODE (DTC) INDEX (BODY CLOSURES) 501-03 Body Closures 2004 Expedition/Navigator DIAGNOSIS AND TESTING Procedure revision date: 08/23/2004

    Power Liftgate Module Diagnostic Trouble Code (DTC) Index

    Power Liftgate Module Diagnostic Trouble Code (DTC) Index

    DTC Description Source Action B1342 ECU Is Defective Power Liftgate Module INSTALL a new power liftgate module. REFER to Power Liftgate Modulein this section. B2477 Module Configuration Failure Power Liftgate Module REFER to Section 418-01. B2522 Vbatt1 Circuit Failure Power Liftgate Module GO to Pinpoint Test B. B2552 Vbatt2 Circuit Open Power Liftgate Module GO to Pinpoint Test B. B2698 Vbatt2 Circuit Failure Power Liftgate Module GO to Pinpoint Test B. B2699 Left Pinch Strip Open Or Short To Battery Power Liftgate Module GO to Pinpoint Test B. B2700 Right Pinch Strip Open Or Short To Battery Power Liftgate Module GO to Pinpoint Test B. B2701 Left Pinch Strip Stuck Active Power Liftgate Module GO to Pinpoint Test B. B2702 Right Pinch Strip Stuck Active Power Liftgate Module GO to Pinpoint Test B. B2703 Open/Close Switch Stuck Active Power Liftgate Module GO to Pinpoint Test B. B2704 Optical Sensor Power Short To Ground Power Liftgate Module GO to Pinpoint Test B. B2705 Optical Sensor 1 Input Not Active During Powered Gate Movement Power Liftgate Module GO to Pinpoint Test B. B2706 Optical Sensor 2 Input Not Active During Powered Gate Movement Power Liftgate Module GO to Pinpoint Test B. B2709 Gate Open Output Short To Battery Power Liftgate Module GO to Pinpoint Test B. B2710 Gate Close Output Short To Battery Power Liftgate Module GO to Pinpoint Test B. B2711 Gate Open Output Short To Ground Or Open Power Liftgate Module GO to Pinpoint Test B. B2712 Gate Close Output Short To Ground Or Open Power Liftgate Module GO to Pinpoint Test B. B2713 Unlatch Output Short To Ground Or Open Power Liftgate Module GO to Pinpoint Test B. B2714 Uncinch Output Short To Ground Or Open Power Liftgate Module GO to Pinpoint Test B. B2715 Cinch Output Short To Ground Or Open Power Liftgate Module GO to Pinpoint Test B. B2718 Gate Ajar Output Short To Battery Power Liftgate Module GO to Pinpoint Test B. B2721 Gate Ajar Output Short To Ground Or Open Power Liftgate Module GO to Pinpoint Test B. B2722 Open/Close Switch Active During Self-Test Power Liftgate Module GO to Pinpoint Test B. B2723 Glass Position Switch Active During Self-Test Power Liftgate Module GO to Pinpoint Test B. B2724 Forkbolt Switch Invalid During Self-Test Power Liftgate Module GO to Pinpoint Test B. B2725 Detent Switch Invalid During Self-Test Power Liftgate Module GO to Pinpoint Test B. B2726 Home Switch Invalid During Self-Test Power Liftgate Module GO to Pinpoint Test B. B2819 Gate Motor Circuit Short To Battery Power Liftgate Module GO to Pinpoint Test B. B2820 Gate Motor Circuit Short To Ground Or Open Power Liftgate Module GO to Pinpoint Test B. B2821 Cincher Motor/Unlatch Actuator Short To Ground Or Open Power Liftgate Module GO to Pinpoint Test B. B2822 Cincher Motor/Unlatch Actuator Short To Battery Power Liftgate Module GO to Pinpoint Test B. B2825 Movement Ceased Due To Excess Speed Deviation Power Liftgate Module GO to Pinpoint Test B. B2903 Chime Output Circuit Short To Battery Power Liftgate Module/ Liftgate Chime Module GO to Pinpoint Test C. C1935 Chime Circuit Failure Power Liftgate Module/ Liftgate Chime Module GO to Pinpoint Test C. U1950 UBP Communication BUS Fault UBP Communi cation REFER to Section 418-00. U2338 Invalid ACM Message Data Power Liftgate Module

Feb 05, 2015 | Lincoln Cars & Trucks

1 Answer

What are the common problems when a 2001 Lincoln navigator lifegate won't open


Do you have power lift gate ?
The power liftgate may not operate under the following conditions:
  • a low voltage or dead battery.
  • a disconnected battery.
  • a power liftgate that has been left open for more than six hours.
  • a power liftgate that has been manually closed and left ajar.
If any of these conditions has occurred, the power liftgate must be reset before performing any pinpoint tests. For additional information, refer to
Power Liftgate Initialization NOTE: If the power liftgate system is turned OFF in the message center, the system cannot be activated with any switches or with the liftgate handle. The system will need to be turned ON for any power operation to occur.
NOTE: The power liftgate may not operate under the following conditions:
  • a low voltage or dead battery.
  • a disconnected battery
  • a power liftgate that has been left open for more than six hours.
  • a power liftgate that has been manually closed and left ajar.
If any of these conditions has occurred, the power liftgate must be reset.
  1. Manually close and fully latch the power liftgate.
  1. NOTE: If the power liftgate does not open during this step, refer to the symptom chart to diagnose the power liftgate for no operation.
    Power open the power liftgate by using the keyfob or overhead console switch.
  1. Once the power liftgate is fully open, close the power liftgate by using the keyfob or overhead console switch

Jan 16, 2015 | Lincoln Cars & Trucks

1 Answer

2011 toyota highlander liftgate speaker doesnt work


go back to where the wattenty work was done because it wasn't done properly. maybe they didn't even put a speaker in it

Nov 21, 2013 | Toyota Highlander Cars & Trucks

1 Answer

Power liftgate will not open with remote, instrument panel control or button in rear cargo on lincoln mkx


It can be faulty switch or its issue with lift gate latch.Its got stuck up hard or cracked inside.It has to be inspected.-----------
There are few help links with proper solutions for these problem.I suggest you to refer the links.
Click the link below:----
2007 Mercury Mountaineer: Liftgate will not Unlock or Open? http://whoisbyme.blogspot.in/2012/06/2007-mercury-mountaineer-liftgate-will.html
------------
Adjust Hydraulic Lifters? http://schematicsdiagram.blogspot.in/2012/04/adjust-hydraulic-lifters.html
-----------
How to open rear lift gate? http://repairhelpcenter.blogspot.com/2011/12/how-to-open-rear-lift-gate.html

--------- Power Liftgate Shuts Down http://whoisbyme.blogspot.in/2012/07/power-liftgate-shuts-down.html
------------ Power Lift Gate Will Not Remain Open http://whoisbyme.blogspot.in/2012/07/power-lift-gate-will-not-remain-open.html
----------- Power Lift-gate will not Operate http://whoisbyme.blogspot.in/2012/07/power-lift-gate-will-not-operate.html
------------- Liftgate will Not Stay Up Open? http://whoisbyme.blogspot.in/2012/07/liftgate-will-not-stay-up-open.html

---------------- Rear Door will not open http://whoisbyme.blogspot.in/2012/07/rear-door-will-not-open.html
------------ 2000 Toyota Corolla: Rear Door wont open from outside or inside? http://whatisbyme.blogspot.in/2012/05/2000-toyota-corolla-rear-door-wont-open.html

--------------

These details will help.
Thanks.

Nov 25, 2012 | 2007 Lincoln MKX AWD

1 Answer

My rear lift gate on 07 tahoe opens and closes its self weather the key is in the ignition or not, opens 1/2 way closes 3/4 then all the way up and all the way down, sometimes it sets off the car alarm- it...


Operation
A power open or close cycle can only be initiated from the fully closed or open positions while the vehicle is in park and the liftglass ajar switch input to the liftgate module is inactive. At any time during a power open or close cycle the operation can be reversed by pressing any of the open/close switches. The power liftgate can be switched to manual mode with the on/off switch in the overhead console and during manual operation the power latch will still operate. During power liftgate operation the liftgate module continuously monitors the liftgate position and load profile. The position is calculated from hall effect sensor counts and the electrical load of the gear motor is used to determine physical resistance to the liftgate. Both of these profiles must be learned before the liftgate can operate properly and relearned any time most liftgate components are serviced.


Object Obstruction Detection
The liftgate control module continuously monitors power liftgate operation and calculates its location and direction of travel using 2 hall effect sensors that are part of the gear motor assembly. The hall effect sensors are 3 wire sensors and are supplied with a 5 volt power circuit, ground and signal circuits from the liftgate control module. The hall effect sensor signal circuits are referenced from battery voltage within the liftgate control module and pulsed low by the hall effect sensors.
The power liftgate system uses a secondary object detection method which consists of object sensors fixed to both sides of the liftgate near the seal area. The object sensors consist of an internal fixed resistor and normally open switch contacts which when closed will bypass the resistor. The signal circuit is supplied 5 volts through a resistor and monitored within the liftgate control module, and during normal power liftgate operation the signal circuit should remain a fixed value. When an object presses one of the sensors the contacts close and the resistor is bypassed causing the signal circuit voltage at the module to go low.

Gear Motor Assembly
The liftgate motor is a bi-directional motor and open or close operation is the result of the direction of the motor rotation. The liftgate module controls the liftgate motor through the control circuits by suppling power and ground in the appropriate polarity. The motor control circuits are monitored by the liftgate module prior to activation for a high or low condition and during motor operation for any irregular current flow conditions.
The liftgate motor clutch engages or disengages the liftgate motor to the liftgate drive gear and is the component that determines power or manual operation. When the liftgate module supplies power to the clutch control circuit the clutch coil is energized and the liftgate motor is engaged to the liftgate drive gear so that power operation can occur. The liftgate module monitors the clutch control circuit at all times for a short high while in an inactive state or a short low or insufficient current flow while in an active state.
The full open switch is part of the gear motor assembly and will close and become active when the liftgate reaches the full open position. The full open switch signal circuit is supplied battery voltage through a resistor and monitored within the liftgate module. The liftgate provides a low reference circuit and when the switch contacts close the signal circuit goes low and the liftgate module determines the switch to be active.

DTC B153A 00: Liftgate Latch Switch Signal Circuit
DTC B153A 08: Liftgate Latch Switch Signal Circuit Signal Invalid

When calibrating the liftgate position, the liftgate module (LGM) is placed in a functional state to learn the liftgate travel limits. DTC B1019 00 will set automatically as an indicator that the system is in learn mode and not as a fault indicator. Once the travel limits are learned by the liftgate module, the LGM will exit calibration mode. If the LGM does not exit learn mode, DTC B1019 00 will remain current and indicate a fault.
DTC B153B 02: Liftgate Open Switch Signal Circuit Short to Ground
DTC B153B 05: Liftgate Open Switch Signal Circuit Short to Short to Battery or Open
DTC B153E 02: Liftgate Position Sensor Signal Circuit Short to Ground
DTC B153E 05: Liftgate Position Sensor Signal Circuit Short to Battery or Open
DTC B153E 08: Liftgate Position Sensor Signal Circuit Signal Invalid

Your best bet , take it to the dealer .

Aug 08, 2017 | Chevrolet Tahoe Cars & Trucks

2 Answers

Power sunroof stuck fully open-motor attempts to close but is in a bind


if you remove the panel you will find an emer key underneath.adrian,,,,

Jul 05, 2010 | 2005 Toyota Highlander

2 Answers

97 toyota 4runner liftgate will not defrost,window will not open, wiper will not work


If the wiper and defroster and window arent running I would guess that there isnt any power going to the rear liftgate. Check the fuses for each and replace if they have blown. Another idea: the wires leading to the liftgate may have become pinched or shorted. If you can inspect the wires from the car into the liftgate (it would be best to remove the liftgate case and examine liftgate internals)

Nov 03, 2009 | 1997 Toyota 4Runner

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

512 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

80407 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...