Question about Cars & Trucks
Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!
Posted on Jan 02, 2017
SOURCE: Replacing exterior door handles 1998 Safari van
remove door panel.. inside door you will see a rod going to the handle..on the end is a clip ..push the clip up off the rod .slide the rod out..remove 2 ..13mm nuts from handle ..remove handle
Posted on Nov 14, 2008
SOURCE: Exterior rear door handle on Honda Accord 2001
To Remove Door Panel on 2001 Honda Accord:
A: To remove the plastic piece with the door lock button and door handle connected to it:
1- Remove the screw in the middle located behind a plastic cover button
2- Push (slide) the whole assembly Forward (toward front of car)
Besides the screw, it is held in place by 3 hooks on the backside that hook into holes in the metal door frame
3- Now unhook handle from small metal bar going through door by pushing (toward door) plastic clip (blue?) off of the bar, then the bar will come out of the clip hole, thus releasing the handle.
4- Depress little grey button /bar (purple painted on it)on elec. connector to seperate connector, thus releasing door lock switch
Now the whole assembly (metal handle, door lock switch, and plastic piece) will come off door panel
B: The door is held on by 2-screws, 7-plastic snaps/plugs, and 1-plastic plug.
The screws are located: bottom of hand hold and the other behind the handle, both covered by little covers that have to be pryed off to access the screws.(hint: the screw with the built in spacer goes behind the handle when you are trying to reinstall)
The 7-plastic snaps: 3 across bottom and 2 on each side. Not visible, they are mounted to the inside of the panel.
The 1-plastic plug is visible at the upper front of the panel and is the same color as the surrounding trim
C: Take off the big plastic triangle piece above the door panel and behind the mirror. Pull/pry off. It has 2 snaps holding it on. one near bottom and one near the front.
D: Light lens prys off from bottom. Unscrew (1/4 turn) the light assembly with bulb still intact from backside of panel
E: Remove the Hand-Hold/window switch assembly:
Posted on Apr 27, 2009
SOURCE: Rear door
Here's a link to the detailed instructions for this repair. It's not too difficult, just a little tedious dealing with small parts.
Good luck!
http://www.findonefindall.com/toyota-sienna/siennareardoor.htm
Posted on May 21, 2009
SOURCE: 2000 Astro van - drivers window only goes up a in increments
The motor is shot. It works a little and overheats, replace the motor . Same thing the the lock acuators. The are trying but have lost the power to move the locks. May as well replace them while the door is apart.
Posted on Aug 16, 2009
SOURCE: 2001 astro chevy van 4.3 engines need to set the timing
The distributor in that engine can only be installed in one position. The hold down is built onto the distributor meaning when it is installed and the engine runs the computer is responsible for the timing. The distributor will move a little but won't correct major timing errors.
Posted on Sep 13, 2009
Apr 14, 2014 | 1993 Chevrolet Astro
Dec 17, 2010 | 2001 Chevrolet Astro
Nov 11, 2010 | 2001 Chevrolet Astro
Mar 06, 2010 | 2001 Toyota Sienna
Feb 18, 2010 | 1988 Chevrolet Astro Cargo
Dec 16, 2009 | 1998 Chevrolet Astro
Aug 05, 2009 | 2001 Chevrolet Astro
Jan 03, 2009 | 2001 Chevrolet Astro
Dec 01, 2008 | 1999 Chevrolet Astro
Aug 03, 2008 | 1997 Chevrolet Astro
97 people viewed this question
Usually answered in minutes!
×