Question about Ford Contour

Open Question

Picture of pcv valve on 98 ford contour v6 - Contour Ford Cars & Trucks

Posted by Anonymous on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Handy Mike
  • 6 Answers

SOURCE: how do i replace the pcv valve on a 2000 explorer xlt v6 sohc?

On the passenger side of the intake manifold, coming off the bottom about the center of the engine front to back, you'll feel a hose that comes off a nipple. That hose makes a 90 degree bend and goes around to the rear of the motor. Where that hose meets the Y-connector from the other side of the intake you'll find the PCV valve. It's almost impossible to see it with the hood installed, and even tougher to reach it.

A good source of information for Ford Explorers can be found here

Posted on Oct 25, 2008

  • 1 Answer

SOURCE: pcv valve :where is it located on a 1999 ford explorer sport 2wd

It is located at the back of the engine near the fire wall. It is gray with a T connector at the top with two hoses coming off of the T and going forward into the intake manifold.

Posted on Mar 07, 2009

  • 2692 Answers

SOURCE: Can't find PCV valve on 2000 Chevy Impala 3.8 V6

PCV . Positive Crankcase Ventalation Valves are always located in the valve cover pans with a hose attached usually leading to the air cleaner, or some other vacuum source..

Posted on Jun 19, 2009

  • 262 Answers

SOURCE: 1998 FORD CONTOURWhere do you find the Maxi Fuse

Hey Willy..The maxi fuse is located under the coil pack. Remove the four screws (9/32" socket) and look about 8" below where the coil pack was sitting. You may have to remove one of the spark plug wires to be able to move the coil pack out of the way. The maxi fuse looks like a box about one inch wide and four inches long with a red battery type wire coming out of each end. With a multimeter set on continuity check for continuity on each end of the "box" by touching both wire ends with the probes. If there is continuity the fuse is good if there is no continuity then your altenator may be shot. Go to a parts dealer or equivilant and have your altenator tested before you try to remove/replace it. Hope this helps..WF

Posted on Feb 17, 2010

  • 262 Answers

SOURCE: How do I replace the idle control valve in a 1998

1.Disconnect the vacuum hose from the exhaust gas recirculation valve. 8adde85.gif
2.Disconnect the idle air control valve electrical connector.e21fa1a.gif 3.Detach the idle air control valve wiring harness from the stud.
4.Remove the idle air control valve.

  • Remove the two nuts.

8176e69.gif I hope this is concise enough for you. Please give me thumbs up to thank me. By the way did I mention this info is FREE!!!

Posted on Mar 27, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Where is the coolant temp sensor 98 ford contour 2.5l v6

May 20, 2018 | 1998 Ford Contour

1 Answer

Cant locate the camshaft position sensor on my 2000 ford contour 2.5L V6

On the 2.5 liter V6, it's just below the front cylinder bank valve cove

Jan 11, 2017 | 2000 Ford Contour

1 Answer

I cant find the location of the pcv valve on my 98 ford contour 2.5 litre

it is located under the hood in the middle upper engine area,on the top, mounted in the valve cover.

Apr 20, 2011 | Ford Contour Cars & Trucks

1 Answer

Replacing PCV 1997 Ford Contour 4 Cyl

If it has a PCV valve you simply unplug the vacuum hose to it and pull it out of the valve cover and replace. Many fords only have a line running from the valve cover to the air intake tube behind the air cleaner.

Feb 24, 2011 | Ford Contour Cars & Trucks

1 Answer

Trying to locate temp switch on 98 ford contour

2.0L or 2.5L V6???

SECTION 303-14A: Electronic Engine Controls - 2.0L Engine 1998 Contour/Mystique Workshop Manual
#4 is coolant ECT - engine coolant temp sensor.


Dec 19, 2010 | 1998 Ford Contour

1 Answer

I cannot find the PCV valve on my 1995 2.0L 16valve engine Ford Contour

if im thinking right its on the drivers side under the exhaust manifold behind the heat shield

Aug 22, 2009 | 1995 Ford Contour

1 Answer

98 ford contour 2.5- a loud roar from front drivers side of car

This sounding like an Idler bearing problem, Sounds like the idler bearing that supports your belt is either loose or needs replading. I say this because when you get the RPMs up on the motor the noise should almost disappear?

Aug 19, 2009 | 1998 Ford Contour

1 Answer

PVC valve location

#10 is the PCV valve.

May 05, 2009 | 1999 Ford Contour

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

168 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

79847 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

5685 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides