Question about Cars & Trucks

Open Question

Where are fuse obdII, nissan 350z

Location fuse Obd2 conection

Posted by Anonymous on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 1066 Answers

SOURCE: diagram for 04 nissan 350Z roadster

one under the hood and one at the drivers kick panel

Posted on Mar 30, 2009

  • 1 Answer

SOURCE: My power seat won't work on my nissan 350z.

It it most likely a blown fuse

Posted on Nov 28, 2009

  • 86 Answers

SOURCE: How to install a window 2004 nissan 350z coupe?

Remove inner panel carefully. find 2 black circle stickers and raise glass to access 2 screws holding glass. Door vent does not need to be removed.

Posted on Feb 04, 2010

  • 19396 Answers

SOURCE: 2003 nissan 350z camshaft sensor location. engine


The CPS is located near the back of the head. It is held by a single 10mm bolt and has a connector with a wiring attached . Below a diagram.Click on the picture to enlarge:




Posted on Feb 18, 2011

  • 80608 Answers

SOURCE: How to use U585 OBDII EOBD CAN Code ScannerOBD2 Reader for VW AUDI

Just plug it in and turn the key to run.

Posted on Apr 20, 2012

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Locating fuse for OBD2 in 1996 pontiac grand am

Locating fuse for OBD2 ??? Need more info ? Fuse for the DLC , that's where you plug in the code reader or fuse's for the PCM/ECM - engine computer ?

Apr 07, 2017 | 1996 Pontiac Grand Am

2 Answers

Where is the diagnostic port of my mazda premacy 2000 model located

Typically the OBD2 port is located below the steering wheel, towards the right or left knee. It should have a cover over it saying "diagnostic" or "obd2" another location is under the hood, typically near a fuse panel. This one should definitely have a cover on it saying "diagnostic" or "obd2"

Feb 15, 2016 | Mazda Cars & Trucks

1 Answer

How to connect code reader

If it's obd2 it should be right under drivers side dash,or under fuse cover,or under a separate cover labeled obd2. As long could Google ob2 connector location for your specific car.

Feb 18, 2015 | Cars & Trucks

1 Answer

How do I get power to the obd connector

Most obd2 connectors are located right under drivers dashboard, or under fuse box cover,or another cover labeled obd2. Just Google your specific make and model. Good luck

Feb 18, 2015 | Cars & Trucks

1 Answer

Werd is the obd conection

where is my DLC, ok, easy. well kinda....
weird?, no not weird, OLD,. old cars dont have OBD2, sorry.
NO COUNTRY stated, you must state that,
1993 is not a OBD2 car mostly. in any country.
that means it's OBD1 so mfg, puts the DLC where ever it wanted
and did. (huge variances)

toy was and early bird to OBD2, see? inUSA !

IF not OBD2
then , its FLASH codes. (easy rules)
TE1 and E1 of the Data Link Connector (DLC) 1 or 2.
now where would that be. answer

real OBD2 connector (USA cars) is just to right of steering
column,at dash edges, TOY cALLS this DLC3 (96 camry)
all scan tools with J1850 Bus work here. (older to newer)

here is a web site dedicated to DLC , musical chairs.
moves every where
see it here

and here too

1st too google hits.

Jan 10, 2014 | 1993 Toyota Camry V6

1 Answer

1998 dodge ram 1500 fuse box diagram

If the truck runs then the issue is probably with the tester you are using and not the OBD2 connection under the dash. If it doesn't run at all then the engine computer is probably defective. Unless of course someone has been making "non-factory" wiring connections under the dash or in the engine compartment and then all bets are off.

May 13, 2013 | Dodge Cars & Trucks

1 Answer

Location for fan fuse on golf pls

it's On battery upper bracket where are 3 fuse small 30A make sure the conection always loose some time the fuse is Ok but the wire loose . you can check your fan motor by remove socet from radator sensor (3 pin ) and conected with small wire the fan will move with tow speed even the first fuse is burn.

Jun 19, 2011 | Volkswagen Golf Cars & Trucks

1 Answer

1993 acura lengend i change the timing belt reset the timing and now the car wont start, it is getting compression and fuel but no spark the coil, fuses are good all wires are conected but still no spark....

There are six coils on the Acura and they are governed by the ECU. The crank position sensor feeds the signal to the computer and is located under the Camshaft pulley on the left (or front) bank of cylinders. You have disconnected it to get the pulley off and may have jammed the small male probes of the connector while putting it back on. You can re-align them and try again. The sensor also may have been damaged and is not "reading" and giving the ECU information to sequence the injectors. It should show on your engine fault code (OBD2 scan). Take out the ALT/Sense fuse to re-boot the computer codes and check. The 93 coupe has variable valve timing and lift control (VTEC) and the ECU controls intake and fuel pressure.

Oct 20, 2010 | 1993 Acura Legend

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

80608 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

15387 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides