Question about Ford Cars & Trucks

1 Answer

Replaced clutch on 2005 ranger ,now truck wont turn over and can't link to pcm

I hear the fuel pump but starer won't crank

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 128 Answers

There's probably a switch that requires the clutch to be depressed before voltage is applied to the starter. It may need adjusting after the clutch replacement or even disconnected.

Posted on Jan 14, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 182 Answers

SOURCE: 2004 ranger fuel pump

did you replace the fuel filter as well

Posted on Sep 28, 2008

  • 54 Answers

SOURCE: wont start, 97 Ranger 2.3 cranks stumbles and dies

If it has fuel pressure at the fuel rail then it is more than likely the computer. You can unscrew the cap on the rail and push the center in with a knife or something and there should be fuel that sprays out. If not then you are not getting fuel to that point.

Posted on Jul 24, 2009

  • 743 Answers

SOURCE: Engine cranks but will not start. No link to PCM

Spray Ether in the air intake...if it doesn't start then, I would suspect the timing chain.

Posted on Oct 11, 2009

emissionwiz
  • 75822 Answers

SOURCE: 1999 Dodge Neon won't start. Battery and all good. Depress clutch, hear a hum (fuel pump?) but nothing. Won't crank. Help!

Go under the dash and bypass the clutch pedal safety switch and see if it starts.

Posted on Feb 14, 2012

  • 9 Answers

SOURCE: 2002 Ford Explorer ran out of gas put gas in and won't restart. replaced fuel pump and fuel filter still won't start. Cranks but won't start

Most Fords have a fuel reset button. When you ran out of gas you tripped the circuit. Most of the time the button will be on the passenger side by the kick panel. The exact location should be in your owners manual or your local library or auto parts store will have a copy of one for your specific vehicle.

Posted on May 08, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1999 ranger wont start


If that was my vehicle I would not have changed one part

I would have gotten out my wiring diagrams & walked thru a
logical sequence of testing what I had & didn't have, as far
as crank sensor output,fuel pressure,injector pulse,etc

Seeing a how pcm's seldom fail ,your just throwing parts at it
& not testing a thing

You need the wiring diagrams to see & learn how the various
systems work

You can actually trigger injectors,coils,relays,etc if you can
use diagrams, test light,meter & jumper wires properly,otherwise
you need professional help

Jan 08, 2013 | 1999 Ford Ranger SuperCab

1 Answer

1998 Ford Ranger won't start.


Check the igntion signal to the starter solenoid.

Oct 10, 2012 | 1998 Ford Ranger

1 Answer

Replaced the fuel pump on 97 dodge mini caravan now motor wont crank like the battery is dead. tried jumping it - nothing. All lights work bright! What did I do wrong?


I would check the starter for voltage first - there is a starter relay that is grounded by the PCM. If the ASD relay is faulty the pcm won't have power. You should have battery power to the starter and power on the solenoid when you turn the key to start.

Aug 31, 2012 | Cars & Trucks

1 Answer

2000 jeep wrangler wont start


If it won't crank, check clutch safety switch and cables for the starter.
If it cranks but won't start, you'll need to find out if it is ignition or fuel to know where to look next.

Jun 26, 2012 | 1994 Jeep Wrangler

1 Answer

2000 jeep wrangler won't start, good crank, no bus


Check fuses first, but could be needs new CPU

Jun 14, 2012 | 2000 Jeep Wrangler

1 Answer

2005 silverado cranks but won't start


I had the same problem . on my 2002 silverado it turned to be the fuel pump failed because the fuel filter was clogged. I did the work myself could saved myself 219.00 and labor if I replaced a 7.00 $ Filter .

Apr 25, 2012 | Cars & Trucks

1 Answer

Engine cranks but will not start. No link to PCM


Spray Ether in the air intake...if it doesn't start then, I would suspect the timing chain.

Oct 07, 2009 | 1996 Saturn SC

2 Answers

Turn the key on and the starter will not engage.


check fuel pressure.if not above recomended spec. replace fuel pump. for starting have solenoid 0n starter checked.

Jan 26, 2009 | 1994 Cadillac Fleetwood

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...