Question about Cars & Trucks

Open Question

How to install water pump on a 2005 ford freestar 3.9l

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

chiquititas
  • 1010 Answers

SOURCE: 2005 Ford Freestar rear air electrical

The blend door is stuck or not receiving the control knob information to change the temperature.

Your car uses an electronic blend door actuator. you will need to locate this devise under the dash. You may have to remove the dash to get to it. You will want to make sure that there is power coming in to the new switch and going out to the Blend Door Actuator. If you do not have power to the switch then find out why and fix the broken wire, if you have power to the motor but it won't move then replace the Blend Door Actuator (BDA).

Make sure the black wire to the BDA is grounded. The do the following:
Test the orange wire going to the BDA and the Yellow wire from the BDA to the switch for postive power. This will tell you if the BDA is getting power in from the car and out to the switch. Then make sure you get a power reading from the Red with White strip and the Red with Lite Green strip, this will tell you that the switch is sending the power back to the BDA to control the temp. If power is coming in to the BDA and not going out to the switch then the BDA is bad. If power is going to and from the switch back to the BDA then that also says the BDA is bad. If the ground is broken that will cause the BDA not to respond.

Posted on Jun 23, 2008

  • 1 Answer

SOURCE: where is the low tire reset button located on 2005 ford freestar?

It is on the same button as the Trip Odometer. Cycle through until you see Tire Reset and hold the button down.

Posted on May 04, 2009

  • 32 Answers

SOURCE: changed caliper on 2005 ford freestar and now brakes are spongie.

When bleading the brakes have someone there watching to make sure the master cylinder never runs out of brake fluid or all of your time spent bleading them will be waisted.

Posted on Jun 08, 2009

  • 543 Answers

SOURCE: Ford 2005 Freestar w/66,000 miles. Check engine

no,but you cold go to autozone they will check the code for free

Posted on Oct 12, 2009

  • 5370 Answers

SOURCE: What is the PCM in

The pcm is located Under the windshield wiper coil on the passenger side of the engine compartment, where water can collect.And yes if its get wet it can get short.The radio,the ac the lights and other electrical functions works intermittently .The cost of pcm is near to $1000.You can get it from autozone service center or from local auto part stores. ---------This will help.Thanks.Helpmech.

Posted on Dec 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Were is the windshield washer fluid sensor 2005 ford freestar ?


It is located in the washer fluid reservoir. To gain access to the reservoir, remove the inner fender panel and you will see the pump and level sensor.

Feb 25, 2015 | 2005 Ford Freestar

1 Answer

I need a video on how to change a water pump on a 2006 ford freestar van


got to autozone.com look up water pump thean hit video it well show you

Feb 18, 2015 | 2005 Ford Freestar

1 Answer

How to remove the water pump in 2005 ford freestar van


U need to jack the motor up on the pass side or yo cannot remove the bolts they will hit the frame

Feb 16, 2015 | 2005 Ford Freestar

1 Answer

How do I change a waterpump on 2005 ford freestar van


Remove the fan while coolant is draining into a bucket. Remove the belt. Once that's all out of the way you can get to the water pump. Remove the lower radiator hose from the pump and the water line to the heater core from the pump. Now remove the securement bolts and remove the water pump.

Sep 25, 2014 | 2005 Ford Freestar

1 Answer

2005 freestar 4.2l, chirp noise on engine located behind water pump..take off the belt and the noise continue...


I knew someone with a Ford Taurus that had the same loud chirp like a loud bird. That turned out to be the cam shaft sensor assembly if memory serves me right.

Sep 15, 2013 | 2005 Ford Freestar

2 Answers

2005 Freestar, squeal noise and sometime van goes dead.


Replace your cam positioning syncronizer head same problem squealing was coming from around alternator water pump area which is exactly where the cam positioning sensor is located not hard to do I did mine in a garage and it took about four hours

Mar 07, 2012 | 2005 Ford Freestar

2 Answers

Changed caliper on 2005 ford freestar and now brakes are spongie.


Use a vacuum pump brake bleeder starting at the furthest point from the master cylinder. They cost abt $35. Be sure to keep master cylinder full... :)

Apr 11, 2009 | 2005 Ford Freestar

1 Answer

FUEL PUMP


its in the fuel tank

Oct 30, 2008 | 2005 Ford Freestar

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

73 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...