Question about Cars & Trucks

1 Answer

Where is the Brake booster located - Cars & Trucks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 21,873 Answers

Depending on the make model and year, it is usually on the back of the master cylinder on the firewall.

Posted on Jan 14, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace brake booster on 2005 Pontiac aztek


Step 1 - Locate the Brake Booster The brake booster is located adjacent to the master cylinder. There will be 4 mounting screws protruding through the booster. The booster is also attached to the brake pedal in the interior of the car. This is where you will start work in replacing the brake booster.
Step 2 - Remove the Brake Booster Start by locating the booster rod that goes through the firewall and is attached to the brake pedal on the interior of the car. Typically, there is a cotter pin that secures the rod to the pedal, but there may also be nuts. When removing any fasteners in the course of this job, make sure to retain the nuts, cotter pins, and various other fasteners as the new brake booster will not come with replacement fasteners.
Remove the fasteners, whether it is a cotter pin or nuts. Slide the rod off the brake pedal. Disconnect the vacuum brake line that connects to the booster. In the engine compartment, there are four bolts securing the booster to the master cylinder and firewall. Loosen and remove these nuts. Remove the nuts (there are usually 2 in addition to the 4 that have already been removed) that secure the brake booster to the master cylinder. Wiggle the brake booster away from the master cylinder. There is a seal between the two. You will need to keep this as the new part does not generally come with another one. Remove the brake booster.
Step 3 - Install the New Brake Booster Set the new brake booster on the four mounting screws. Tighten the nuts on the bolts to the master cylinder. Insert the push rod through the firewall. Start these by hand so that the threads are not ruined. Reattach the vacuum hose, then the nuts to the 4 mounting screws. Reattach the push rod to the brake pedal by whatever means it was originally secured with, whether by cotter pin or by bolts.
Step 4 - Bleed the Brakes You will need to bleed the brakes after replacing the brake booster

Jul 11, 2016 | 2005 Pontiac Aztek

1 Answer

How to remove the brake booster


What you have is a standard, run-of the mill brake booster. First, remove the vacuum booster hose from the check valve. Then remove the two nuts hold the brake master cylinder to the booster. Carefully move the master cylinder to one side. The lines will allow for movement, but be sure not to overstress of break any of them. Now, under the dashboard, find and remove the clip that secures the brake pedal to the booster actuator rod. After that, still under the dashboard, locate the two nuts the hold the booster to the firewall and remove them. The booster will then pull straight out if the firewall. See pictures for relative locations.

25876613-1koo1g3m4mdpobxz0swf2e3d-5-0.jpg

25876613-1koo1g3m4mdpobxz0swf2e3d-5-1.jpg

Sep 22, 2015 | 2000 Oldsmobile Alero

1 Answer

Step by step instructions for replacing brake booster on a 1999 Toyota Camry


its my pleasure to answer your question how to replace the brake booster :
1 With the engine off, step on the brake pedal several times to relieve the brake booster of vacuum.
2 Press the brake pedal down and start the engine. Verify that the brake pedal sinks slightly. Turn off engine.
3 Remove the vacuum hose from the brake booster.
4 Remove the brake lines from the master cylinder. Remove the master cylinder from the brake booster. Plug the fittings to prevent brake fluid seepage.
5 Disconnect the brake pedal from the push rod.
6 Have an assistant hold the brake booster from inside the engine compartment. Remove the nuts that hold the brake booster to the firewall. These nuts are usually located under the dash on the interior of the firewall.
7 Remove the brake booster.
8 Install the new brake booster to the firewall. Tighten the mounting nuts.
9 Connect the push rod to the brake pedal.
10 Connect the vacuum hose to the brake booster.
11 Attach the master cylinder to the new brake booster and reconnect the brake lines.
.12 Bleed the brakes at the master cylinder.

Oct 04, 2013 | Cars & Trucks

1 Answer

How to remove brake booster on 1999 Toyota Camry


The following steps will help you to replace a Toyota Camry brake booster :
1 With the engine off, step on the brake pedal several times to relieve the brake booster of vacuum.
2 Press the brake pedal down and start the engine. Verify that the brake pedal sinks slightly. Turn off engine.
3 Remove the vacuum hose from the brake booster.
4 Remove the brake lines from the master cylinder. Remove the master cylinder from the brake booster. Plug the fittings to prevent brake fluid seepage.
5 Disconnect the brake pedal from the push rod.
6 Have an assistant hold the brake booster from inside the engine compartment. Remove the nuts that hold the brake booster to the firewall. These nuts are usually located under the dash on the interior of the firewall.
7 Remove the brake booster.
8 Install the new brake booster to the firewall. Tighten the mounting nuts.
9 Connect the push rod to the brake pedal.
10 Connect the vacuum hose to the brake booster.
11 Attach the master cylinder to the new brake booster and reconnect the brake lines.
.12 Bleed the brakes at the master cylinder.

Oct 04, 2013 | Cars & Trucks

1 Answer

How do i replace the brake booster on a 98 Mercury villager


12 specific steps will help you :
1 With the engine off, step on the brake pedal several times to relieve the brake booster of vacuum.
2 Press the brake pedal down and start the engine. Verify that the brake pedal sinks slightly. Turn off engine.
3 Remove the vacuum hose from the brake booster.
4 Remove the brake lines from the master cylinder. Remove the master cylinder from the brake booster. Plug the fittings to prevent brake fluid seepage.
5 Disconnect the brake pedal from the push rod.
6 Have an assistant hold the brake booster from inside the engine compartment. Remove the nuts that hold the brake booster to the firewall. These nuts are usually located under the dash on the interior of the firewall.
7 Remove the brake booster.
8 Install the new brake booster to the firewall. Tighten the mounting nuts.
9 Connect the push rod to the brake pedal.
10 Connect the vacuum hose to the vacuum brake booster.
11 Attach the master cylinder to the new brake booster and reconnect the brake lines.
.12 Bleed the brakes at the master cylinder.

Sep 24, 2013 | Cars & Trucks

2 Answers

Brakes


There should be two or four mounting bolts accessed from under the dash. Usually the booster has studs and you remove the nuts.

Jul 07, 2013 | 1998 GMC Jimmy

2 Answers

How to repair a brake booster for a 1992 Chevrolet Cavalier


Click here Jeremy to see how to replace brake booster.

Dec 10, 2012 | 1992 Chevrolet Cavalier

1 Answer

2002 jaguar x type how do remover brake booster hoes connector from the manifold


Check the help link below and follow the procedure:----

How to replace Brake Power Booster?

http://repairhelpcenter.blogspot.in/2012/02/how-to-replace-brake-power-booster.html

---------

Where is Power Brake Booster located on Car?

http://howtobyme.blogspot.com/2011/12/where-is-power-brake-booster-located-on.html

---------

How to Replace Power Brake Booster on 1996 GMC Jimmy?

http://schematicsdiagram.blogspot.com/2011/12/how-to-replace-power-brake-booster-on.html

---------
These will help.
Thanks.

Nov 28, 2012 | Cars & Trucks

1 Answer

Replace brake booster


  • Slide the tube nut wrench over the brake line to the master cylinder connection. The master cylinder is normally on the driver's side of the engine bay and mounted on the firewall. Orient the wrench so that it fits over the tube nut on the end of the brake line.
  • 2Disconnect the brake line. Turn the nut counterclockwise to remove. Note the location of each brake line. There are four lines total, and they need to be put back in the same location when reinstalling the lines. You may want to mark them with masking tape and permanent marker.

  • 3Unplug the master cylinder cap electrical plug.
  • 4Remove the brake master cylinder to brake booster bolts with a socket wrench.
  • 5Back the master cylinder off the brake booster.
  • 6Unbolt the bolts holding the brake booster to the firewall on your vehicle.
  • 7Pull the cotter pin out of the brake pedal to brake booster connecting pin with a pair of pliers. This is done inside the vehicle down in the driver side foot well.
  • 8Pull the brake pedal to brake booster connecting pin out to disconnect the brake pedal from the brake booster connecting arm.
  • 9Mark and remove the vacuum hoses on the brake booster and slide the booster off the firewall.
  • 10Install the new brake booster. Installation is the reverse of removal
  • Aug 06, 2012 | 1998 Lincoln Mark VIII

    2 Answers

    How do i change a brake booster


    from autozone.com:

    1. Disconnect the negative battery cable.
    2. Apply the parking brake.
    3. Unplug all necessary electrical connections.
    4. Remove the master cylinder from the booster and pull it off the studs, CAREFULLY! It is not necessary to disconnect the brake lines.
    5. Disconnect the vacuum hose from the check valve.
    6. If necessary, remove the brake light switch.
    7. Disconnect the booster pushrod at the brake pedal.
    8. Remove the booster mounting nuts, located on the inside of the firewall.

    24cafd9.gif


    Fig. Fig. 1: Vacuum booster mounting

    1. Lift off the booster and remove the gasket.

    To install:
    1. Install the booster with a new gasket.
    2. Tighten the booster mounting nuts to 21 ft. lbs. (29 Nm) on all except 1996-98 models. On 1996-98 models, tighten the nuts to 26 ft. lbs. (36 Nm).
    3. Install all remaining components.

    Oct 29, 2010 | 1998 Chevrolet Blazer

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    14 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Cars & Trucks Experts

    yadayada
    yadayada

    Level 3 Expert

    75807 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22133 Answers

    Randy Ohler

    Level 3 Expert

    14585 Answers

    Are you a Car and Truck Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...