Question about 2006 Chevrolet TrailBlazer LT

1 Answer

Parking Brake, ABS, Traction Control & Anti Skid lights on

When I start the vehicle, none of the lights come on. Within the first 1/4 mile of driving, you can feel the ABS acting up with a pulsating feel in the brake pedal. Then I get exactly 33 tones and the parking brake, abs, traction control and anti skid lights all come on. The brakes work fine after that. The system resets itself everytime you turn off the engine. Any idea what can be causing this problem?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,669 Answers

One or more of the sensors in the wheels that are responsible for these functions is faulty. It is sending a signal that is mucking up the calculations that control the brakes and engine for traction control and anti skid. All of them need to be checked!

Posted on Jan 14, 2013

  • Ken Heverly Jan 16, 2013

    Are you talking about the tone ring inside the axle?

  • Leigh Perlmutter
    Leigh Perlmutter Jan 16, 2013

    No, the sensors on the wheels and brakes.

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
gladys_neal
  • 334 Answers

SOURCE: abs and traction control lights on 2005 equinox

check connections at all wheel speed sensors or faulty sensor/tone rings

Posted on Nov 07, 2009

  • 5 Answers

SOURCE: ABS light and Traction control light stay on.

That "grindy" feeling is when the ABS kicks in. It's only suppose to activate when you slam on the brakes and the wheels would normally lock. Instead, ABS will very quickly pump the brakes on and off, to prevent the wheels from locking (making a giant skid mark) and stopping the car more effectively. Generally this only happens if you slam on the brakes or loose traction due to rain or snow while braking. If this is happening often and the brake light is on, on the dash, then you need to get this checked out by a qualified mechanic ASAP.

Posted on Dec 01, 2009

  • 119 Answers

SOURCE: 2000 chevy impala 3.8 lt engine, brake pedal

it looks like you need to resurface your rotors and bleed your brake lining and adjust rear shoes if applicable and sand front pads before you install them

Posted on Jan 19, 2010

tbirdfan1
  • 3051 Answers

SOURCE: ABS LIGHT AND SERVICE TRACTION CONTROL LIGHTS

Hello there:
There is a abs wheel sensor that is on the hubs on these vehicals that should be changed if the light that you are getting comes and goes this happens when the signal from the sensor to the abs system has been interupted you can take it to autozone and have them clear the code for you till you can get this repaired these sensors can cost around 150 to replace ok

Posted on Jul 14, 2010

  • 15180 Answers

SOURCE: 2001 impala- Traction, Abs, Brake lights on

abs sensor is built into hub[bearing]common problem when changing them and or brakes r that the sensor connection is not properly reconnected or wire got damaged recheck the sensor wiring and that connector is connected to clip by strut clip is part of system

Posted on Jul 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Abslight stays on. How to fix? This is a2007trailblazer?


First you need to have EBCM - electronic brake control module check for DTC'S - diagnostic trouble code's . If the light is on there is a code stored . I think most part stores can do this and for free . After you find out what code is stored , looking up that code in service repair information for diagnostic trouble shooting chart would be next step . There are a few codes too.
DTC C0035 or C0040
DTC C0045 or C0050
DTC C0110
DTC C0131
DTC C0161
DTC C0186
DTC C0196
DTC C0201
DTC C0240
DTC C0241 or P0856
DTC C0244 or P1689
DTC C0245
DTC C0283
DTC C0287
DTC C0290 or C0292
DTC C0455
DTC C0550
DTC C0558

Find the code do the diagnostic's , fix the problem , wiring issue's , a sensor , bad module ,what ever it is . The light will go out then . Here is a sample of code discription .
• DTC C0035 Left Front Wheel Speed Sensor Circuit
• DTC C0040 Right Front Wheel Speed Sensor Circuit

Dec 30, 2016 | 2007 Chevrolet Trailblazer

2 Answers

ABS & Traction control light are on, what is causing this?


About 39,700,000 results (0.44 seconds) Search Results

    Traction Control Light is on Inspection - YourMechanic

    www.yourmechanic.com > Auto Repair and Maintenance Services
    As a result, sometimes an issue in the ABS can trigger the traction control light. If this is the case, then both the ABS and Traction Control lights will be on.

    My anti-lock brakes and service traction control lights came on ...

    https://answers.yahoo.com/question/index?qid...
    Oct 16, 2006 - I drive a 2000 chevy impala...i have 135,000 miles on my car. ... The problem is that starting in '92, Anti-Lock Brakes are controled electronically, so if there is a problem with the sensor, your ABS might fail when you need them the most. ...ABS (?nti-lock Brake System) is a ...

    How To Fix ABS & Traction OFF / Service Traction System ...

    ? 5:35
    https://www.youtube.com/watch?v=KFQphWamcjQ
    Feb 17, 2014 - Uploaded by Zero Gar
    How To Fix ABS & Traction OFF / Service Traction SystemLight Monte ... side connector that leads from the ABS controlmodule to the speed ...

Feb 05, 2016 | Cars & Trucks

2 Answers

Why does my ABS light stays on and sometimes i get a vibration in the brake petal causing my 2002 Cadillac escalade not wanting to stop?


Sounds like a fault with the Antilock Braking System. The vibration in the pedal is the ABS working. With your foot on the brake pedal, it releases and re-applies the brakes to stop a skid from the wheels locking up. You need professional service for brakes.

Seems to be a known issue on all Cadillac and requires the ABS module to be replaced.

ABS Light Due to ABS Control Module Failure : Cadillac ...

repairpal.com > Problems > Cadillac > DeVille Cadillac DeVille ABS Light Due to ABS Control Module Failure. This is a verified problem based on 126 reports. Learn more about this problem, when it occurs ...

ABS Light Due to ABS Control Module Failure : Cadillac ...

repairpal.com > Problems > Cadillac > Seville STS Traction control and ABS lights stay on dash. This is due to ecbtm Module gone bad. replace Module and this should fix the problem. You can go by the VIN and ...

ABS Light Due to ABS Control Module Failure : Cadillac ...

repairpal.com > Problems > Cadillac > DeVille DTS ABS Light Due to Control Module Failure on Cadillac DeVille DTS. The anti-lock ... ABS and Traction control light stays on. ... abs light to abs control stay on.

ABS Light Due to ABS Control Module Failure : Cadillac ...

repairpal.com > Problems > Cadillac > Seville SLS ABS Light Due to Control Module Failure on Cadillac Seville SLS. The anti-lock brake ... SLS135,000Jumsee. Abs and traction lights stay on when started.

Jan 12, 2016 | Cadillac Cars & Trucks

1 Answer

ABS CHECK LIGHT DOESNT COME ON WHEN YOU TURN KEY ON


1. I would not be concerned because if there was a failure in the ABS you would definitely get an ABS warning light and the ABS and most likely the stability control/traction control systems (with added warning lights) will all switch off .

2. You can test if the ABS is operational. On a very quiet damp surface, straight, wide road( with NO other cars around), apply your brakes hard from a very low speed - up to 20 mph ONLY driving in a straight line - until the car stops. The front brakes should attempt to lock up under hard braking and if the ABS is operational you will feel it kick in and the brake pedal will pulsate as the ABS constantly allows brake pressure and then releases it to prevent the wheels from locking up on the damp road. If the ABS does not kick in be ready to release the brake pedal quickly to allow the wheels to rotate so you can steer the car safely. Without the ABS the front wheels should begin to lock up on the damp road surface due to the low level of tire grip. ONLY test this at very low speed and ONLY when driving in a straight line on a straight section of wide road with no other vehicles around.

Dec 15, 2015 | Cars & Trucks

1 Answer

Trac control light on & anti lock lite came on same time stays on


That means there is a problem with the ABS , has DTC'S - diagnostic trouble codes in the EBCM - electronic brake control module . You need to have diagnostics run on it !
Traction Control/ Stabilitrak Off: Refer to ABS Description and Operation in Antilock Brake Systems
This vehicle is equipped with the BOSCH 5.3 antilock braking system.
The vehicle is equipped with the following braking systems:
?€¢
Antilock Brake System (ABS)


?€¢
Dynamic Rear Proportioning (DRP)


?€¢
Traction Control System (ETS) (w/NW7)


?€¢
Traction Control System (TCS) (w/NW9)


?€¢
Vehicle stability enhancement system (VSES)

Oct 04, 2015 | 2004 Pontiac Grand Prix GTP

1 Answer

My kia magentis 2007 crdi on tick over if I push my brake pedal down I get a pulsating coming thru the pedal


Not sure what you mean by tick over but pulse through pedal is usually from ABS / stability system. If you mean you feel this when first starting up vehicle it is probably system doing self test. They do self test at start but usually you don't feel it that much. May be nothing - especially if no light coming on. Only other pulse you may feel is if power brake booster is failing. If you are driving and brakes feel hard to push at times then I would suspect the brake booster for that.

Jan 17, 2015 | Kia Cars & Trucks

1 Answer

Light abs traction control stays 1998 buick park avenue


PRE-DIAGNOSTIC INSPECTIONBefore diagnosing ABS/TCS, perform a comprehensive visual inspection of system as follows.Check ABS/TCS wiring harness connectors for looseness. Check harness routing; pay particular attention to wheel speed sensor wiring harness routing. Check fuses No. 1D, 5B and 6B in instrument panel fuse block. Check fuses No. 1 and 2 in underhood fuse block. Check brake fluid level in master cylinder reservoir. Check brake fluid level in Pressure Modulator Valve (PMV) assembly reservoir. Ensure parking brake is fully released. Ensure parking brake switch is functioning properly. Always perform ABS/TCS system functional check before using DIAGNOSTIC CODE CHARTSThe EBCM/EBTCM has self-diagnostic capability, which can detect system failures. Fault codes stored by EBCM/EBTCM can be displayed using Tech 1 scan tester. There are no provisions for flash code diagnostics.Begin ABS/TCS diagnosis with PRE-DIAGNOSTIC INSPECTION procedure. If failures are found during pre-diagnostic inspection, perform necessary repairs, and proceed with ABS/TCS FUNCTIONAL CHECK. See Fig. 5 .If no failures are found during pre-diagnostic inspection, go to ABS/TCS FUNCTIONAL CHECK. See Fig. 5 . The ABS/TCS FUNCTIONAL CHECK will either indicate ABS/TCS is functioning properly or direct technician to various diagnostic procedures such as diagnostic charts, symptom diagnosis or BRAKE warning light diagnosis.CHART D - TRACTION OFF WARNING LIGHT ON CONTINUOUSLY & NO DTC SET (BUICK WITH UH8 OR U2A INSTRUMENT CLUSTER)Circuit DescriptionWhen ignition switch is first turned to RUN position, EBTCM goes through a self-test, which lasts 2-4 seconds. During self-test, EBTCM commands TRACTION OFF indicator warning light on. Powertrain Control Module (PCM) can also command EBTCM to set a Code 75 which will illuminate TRACTION OFF indicator.Traction control switch is located either on instrument panel center trim plate or driver's front door trim panel. Switch allows driver to select traction control mode (on/off). When traction control system is turned off, TRACTION OFF warning light comes on.EBTCM monitors transaxle temperature through

Jul 12, 2014 | 1998 Buick Park Avenue

1 Answer

2004 Ford F150 4.6L rear wheel drive. ABS pulsates at low speeds.


This may be an old school question, do you feel pulsating on the brake pedal? Have the brakes, themselves, been checked?

May 06, 2014 | 2004 Ford F150

1 Answer

Reset abs light pajero


When the ABS comes into play from heavy braking you will feel a pulsating of the brake pedal under your foot. This is the brake pressure, on off on off as the wheels stop start stop etc. The ABS will not control the vehicle direction but by allowing the wheels to turn under brakes and not lock up you have control of the steering and the direction the vehicle goes.The ABS will not stop you quicker and in fact on ice or loose surface the distance to stop will be increased. As I said all the ABS does is give you steering ability under brakes.. Take the vehicle to an accredited brake shop and have the ABS tested if you feel that it is no operating properly

Jan 02, 2014 | Cars & Trucks

2 Answers

Pulsating brakes


you could try the abs pump itself try getting one from a breakers yard
hope this helps

Oct 22, 2013 | 2003 Buick Century

Not finding what you are looking for?
2006 Chevrolet TrailBlazer LT Logo

1,078 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

80339 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...