Question about 2002 Buick LeSabre

1 Answer

2002 buick rear transmission mount

Tried to remove rear mount and was unable to remove the top mount nuts because they could not get a wrench on them . Removed the bracket it mounts to but could not remove the two parts together because there was not enough room . How do I get around this ?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

REMOVER TRANSMISSION MOUNTH BUICK 2002

Posted on Feb 26, 2013

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
dennymulford
  • 1055 Answers

SOURCE: 1999 Park Avenue water pump removal

if thats got the 3800 or 3100 in it your taking out the wrong bolts!!!!!!!
your trying too remove the whole housing
you dont need too do that !!!
take off the 4- 10 mm bolts on the waterpump pully,then remove the bolts behind it i belive that there are 8 of them that takes the pump from the housing!!

Posted on Jun 22, 2009

  • 71 Answers

SOURCE: 1992 Buick LeSabre - Water Pump Bolts Near Engine Mount.

I'm not sure what motor you have in that Buick, but my wife's 92 Old's water pump went out and I had a heck of a time with the bottom two bolts. I talked to a mechanic and he told me to put a piece of wood on top of a floor jack, slide it under the oil pan and lift the motor off it's mounts to gain easier access ,and after I did, with a lot of patience I got the job done.(About 2 hours, a 1/4 turn a a time) I hope this helps

Posted on Aug 27, 2009

Smooth_Gecko
  • 125 Answers

SOURCE: trying to remove rear wheel cylinder from buick

You shouldn't have to pull the axle.
Do one side at a time so you always have a reference to go back to, even if it is a mirror of it.
Always do both cylinders though, or the other one will leak in a couple of weeks or so. They both do the same amount of work though so their time is gone.
Not familiar with your exact model, but maybe you can loosen the backing plate ( that the cylinders bolt onto ) and give yourself a bit of room.
You often do have to remove the shoes and handbrake lever to get them out easily.
Work safe and careful :)

Posted on Oct 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove 02 buick rendezvous radiator transmission line


Hey Big, You will need a set of FLARE NUT wrenches... these are critical.. without them, you will round off the connector nuts, collapse the ends of the nuts or twist off the radiator connections..the removal is pretty straight forward.. HOLD the radiator connection with one wrench and loosen the line nuts with another wrench....

Jun 27, 2017 | Buick Cars & Trucks

1 Answer

How do you remove transmission cooler lines from the radiator on 2003 Buick Century.


Hey Richard.
BE careful, you will need some flare nut wrenches.... if you use anything else you run the risk of rounding off the nuts, twisting the ends out of the cooler($$$$)... you MUST use a flare nut wrench on the nut of the line and a flare nut wrench on the nut (on/of the cooler) that the line screws into.

Jun 24, 2017 | Buick Cars & Trucks

1 Answer

How to replace rear engine motor mount


1994-1997 Honda Accord Rear Motor Mount - YouTube

? 13:31
https://www.youtube.com/watch?v=QTDLBZonjvo
Aug 14, 2014 - Uploaded by NutzAboutBolts
1996 Honda Accord rear engine mount Tools: Impact wrench 3/8 ratchet ... Wat size are those bolts in the rear motor mount, I have to replace them ..... 1998-2002 Honda Accord 3.0 V6 Spark Plug Replacement - Duration: ...

How to Replace the Motor Mount on a Honda Accord ...

? 5:28
https://www.youtube.com/watch?v=jCIBNq0jg0U
Oct 17, 2013 - Uploaded by Chandler Cox
How to Replace the Motor Mount on a Honda Accord .... I have 2001 Accord and engine/front vibrates when car is idle. .... onreplacing and removing rear mounts for this year and model car.... 1998-2002 Honda Accord 3.0 V6 Spark Plug Replacement - Duration: 12:48. by CharlietoKind 103,467 views.

How To Change A Motor Mount and Transmission Mount ...

? 29:43
https://www.youtube.com/watch?v=vkO19Ux9q9M
May 30, 2013 - Uploaded by klowny1969
Step by step honda transmission motor mount and transmission... 2000 2001 2002 2003 2004 2005 engine mount how to replace install check change ... MAKE A VIDEO TO INSTALL THEREAR MOUNT MOTOR PLEASE .


Dec 16, 2015 | 2002 Honda Accord

1 Answer

02 liberty rear wiper dose not work plugin has power changed wiper motor still doses work


There is a nut under the black plastic bezel that needs to be removed. Here is the complete procedure for you to look at. Its possible that your arm isn't adjust at wiper motor...

REMOVAL
- Disconnect and isolate the battery negative cable.
- Remove the rear wiper arm from the rear wiper motor output shaft. (Refer to 8 - ELECTRICAL / REAR WIPERS / WASHERS/REAR WIPER ARM - REMOVAL).
- Using a small thin-bladed tool, gently pry at the notch in the base of the rear wiper motor output shaft bezel to unsnap the nut cover from the bezel (REAR WIPER MOTOR OUTPUT SHAFT NUT REMOVE/INSTALL). Be certain to take proper precautions to protect the outer tailgate panel and its paint finish from damage during this procedure.
- Remove the nut that secures the rear wiper motor output shaft to the outer swing gate panel (REAR WIPER MOTOR OUTPUT SHAFT NUT REMOVE/INSTALL).
- Remove the bezel and gasket from the rear wiper motor output shaft.
- Remove the trim panel from the tailgate inner panel. (Refer to 23 - BODY/SWING GATE/TRIM PANEL - REMOVAL).
- Disconnect the tailgate wire harness connector for the flip-up glass ajar switch from the flip-up glass latch connector receptacle.
- Disconnect the tailgate wire harness connector for the rear wiper motor from the motor connector receptacle (REAR WIPER MOTOR REMOVE/INSTALL).
- Loosen the two screws that secure the rear wiper motor mounting bracket to the top of the tailgate inner panel.
- Slide the rear wiper motor and mounting bracket forward far enough to disengage the two mounting screws from the keyed slots in the top of the tailgate inner panel.
- Remove the rear wiper motor and mounting bracket from the tailgate as a unit.

zjlimited_494.gif

1 - BEZEL AND GASKET
2 - OUTPUT SHAFT
3 - TAILGATE OUTER PANEL
4 - NUT
5 - NUT COVER

What you will need to do is to remove the small plastic cap on the wiper arm by prying it off with a screw driver. Then remove the nut that holds the arm onto the shaft. Then get yourself a battery cable puller (from auto parts store) and pull the arm off of the shaft..

zjlimited_495.gif

1 - SPARE TIRE
2 - WRENCH
3 - FLIP-UP GLASS
4 - PARK RAMP
5 - REAR WIPER ARM
6 - PIVOT COVER

Jul 19, 2011 | 2002 Jeep Liberty

1 Answer

I have a 1993 saturn station wagon with a 4 cylinder. I need to remove the starter for replacement what is the easiest way to do this?


Hello, Disconnect the negative battery cable with a wrench. (2)Lift the front of your Saturn with a floor jack. Position two jack stands under the front end and lower the vehicle onto them(3)Find the starter at the rear of the engine where it couples with the transmission. It is a cylindrical component about 7 inches in length and 4 inches in diameter. The starter solenoid, a smaller cylindrical component, mounts on top of the starter. Pull off the pin holding the shield to the starter solenoid with a pair of slip-joint pliers and remove the shield.(4)Spray the electrical and cable connections at the back of the starter solenoid with penetrating oil. This will help the retaining nuts release easier.(5)Unfasten the retaining nuts securing the battery cable and electrical connectors to the back of the starter solenoid using a wrench.Put on your safety goggles and crawl under your Saturn. Unfasten the lower starter mounting bolt with a ratchet, short ratchet extension and socket. Remove the upper starter mounting bolt with an obstruction wrench. If you cannot reach the upper bolt from underneath, try reaching the bolt through the opening on the intake manifold support bracket.6)Unfasten the bolt holding the rear starter bracket to the engine using a wrench, if your starter has this bracket (not all 1993 Saturns do)(7)Remove the starter from the engine compartment.
Thanks

Jul 10, 2011 | Saturn SL1 Cars & Trucks

1 Answer

How do you remove the top nut on rear shocks on a 1996 Buick Lesabre Custom


The top of the shaft is squared off so a wrench can fit on it.
Slip a box wrench of the correct size over the shaft and round the nut the take a wrenc that fits the shaft and hold it steady whilee you loosen the nut.
They can be stubborn!

Jan 06, 2011 | 1996 Buick LeSabre

1 Answer

Ho do you replace the rear transmission mount on a 1999 buick lasabre


unbolt mount from transmission while supporting with jack. Jack up slightly. Unbolt old mount from cross member. Replace in reverse order, do final tightening with jack removed. A few vehicles require the cross member to be removed from frame to access the lower bolts/nuts.

Oct 03, 2010 | 1999 Buick LeSabre

1 Answer

How do you replace ball joints


Removing the Ball Joint Step 1 Loosen the lug nuts on the front wheel assembly with the ball joint you need to replace. Do not remove the lug nuts.
Step 2 Set the transmission in neutral (manual) or park (automatic) and raise the wheel off the ground using a floor jack. Then support the car on a jack stand.
Step 3 Chock the rear wheels and apply the parking brake.
Step 4 Remove the wheel lugs and the wheel assembly.
Step 5 Remove the mounting nut and dished washer that secure the stabilizer bar to the control arm. Use a wrench or ratchet and socket.
Step 6 Unscrew and remove the mounting bolt and nut holding the inner side of the control arm to the car's body. This will relieve the tension on the stabilizer bar. Use a wrench to hold the mounting bolt as you unscrew the nut with a wrench or ratchet and socket.
Step 7 Unscrew the bolt on the steering knuckle that holds the control-arm ball joint to the knuckle. Use a wrench or ratchet and socket.
Step 8 Spread the steering knuckle joint that holds the control-arm ball joint to the knuckle. Use a large screwdriver or pry bar. Then separate the ball joint from the steering knuckle.
Step 9 Pull the control arm from the stabilizer bar.
Step 10 Remove the stabilizer bar spacer from the control arm and keep it in a secure place. You will need to use it on the new control-arm ball joint assembly.
Installing the Ball Joint Step 1 Insert the new control-arm ball joint stud into the steering knuckle joint. As you look through the mounting bolt hole on the steering knuckle, align the notch on the ball joint stud with the hole. Insert a new ball joint mounting bolt and start a new nut on the bolt. Tighten the nut.
Step 2 Mount the stabilizer bar spacer in the control arm, then insert the stud bolt at the end of the stabilizer bar into the control arm mounting hole and spacer.
Step 3 Set the other end of the control arm in its mounting position and insert the mounting bolt. Then start the mounting nut on the bolt by hand.
Step 4 Hold the head of the mounting bolt that secures the control arm to the car's body using a wrench, then tighten the nut.
Step 5 Secure the stabilizer bar to the control arm with the dished washer and mounting nut. Tighten the nut.
Step 6 Install the wheel assembly and lugs. Tighten the lugs with the lug wrench just enough to hold the wheel assembly firmly in place.
Step 7 Lower the vehicle and finish tightening the wheel lugs.
Step 8
Remove the chocks from the rear wheels.

Aug 08, 2010 | 1998 Ford Escort

1 Answer

Need to replace a back up sensor


TRANSMISSION RANGE SENSOR LOCATED ON TOP OF TRANSAXLE.FIRST YOU HAVE TO PUT CAR IN PARK SETTING PARKING BRAKE PLACE TRANSMISSION IN NEUTRAL POSITION THE BACK UP SENSOR ON TOP OF TRANSAXLE.DISCONNECT THE SHIFT CONTROL CABLE AND ELECTRICAL CONNECTOR TO TRANSMISSION RANGE SENSOR.REMOVE TRANSMISSION RANGE SENSOR LEVER NUT AND SENSOR MOUNTING SCREWS THEN REMOVE SENSOR.YOU NEED A SPECIAL TOOL TO ADJUST THE TRANSMISSION RANGE SWITCH. A SMALL ADJUSTABLE WRENCH MAY WORK.

Jun 08, 2010 | 2006 Buick Lucerne

2 Answers

How hard is it to replace a 2002 lancers motor mounts


Should be No Problem. Remember to keep the Jack under the Motor until you are finished with all Mounts.

Jan 16, 2009 | 2002 Mitsubishi Lancer

Not finding what you are looking for?
2002 Buick LeSabre Logo

Related Topics:

140 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...