Question about 2008 GMC Yukon

1 Answer

Bcm was replaced and now my remotes wont work. done all techniqiues. i cant get remote key learning active to engage.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 73 Answers

Get a haynes manual for it at a parts store or on ebay,it will tell you what you need to know and do and is well worth the investment

Posted on Jan 14, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Instructions on how to program GM remote key OEM 22733524


Switch ignition ON.

Repeatedly press vehicle information button (it is usually located on the right or left from the steering column depending on year make and model until PRESS TO RELEARN REMOTE KEY is displayed.

Press set/reset button until REMOTE KEY LEARNING ACTIVE is displayed.

Programming mode activated, proceed as follows:

Press and hold LOCK and UNLOCK remote buttons on first remote transmitter simultaneously for 15 seconds.

Wait for acoustic signal (indicates correct programming).

Repeat above procedure to program remaining remote transmitters.

Switch ignition OFF to exit programming mode.

May 17, 2015 | 2007 Pontiac G6 GT Convertible

1 Answer

Rocker switches,nor remote will lock or unlock doors fuse good


So , the power door locks won't lock or unlock with switches inside the vehicle or with the keyless entry remote fob.??? Is this correct ????
Do you know what a BCM - body control module is ? Do you know what diagnostic trouble codes are ? If not your best bet would be to take your vehicle to a GM dealer or someother qualified repair shop.
DTC B3142 or B3143
The body control module (BCM) provides an output to the driver switch assembly through the door unlock control circuit for controlling automatic door unlock, anti-lockout, and keyless entry unlock functions.
DTC B3152 or B3153
It could be the driver door master switch , could have broken wires inside the rubber boot from the body to the door . Do the power windows work ?
The keyless entry system has the following main components:
• The transmitters
• The body control module (BCM)
When you press a button on a transmitter, the transmitter sends a signal to the BCM. The BCM interprets the signal and activates the requested function.

How did you do this ,,checked and made sure locks and remote programmed,they were,but still do not work ?????

Need a scan tool to program
Important: All key fobs must be programmed each time any one fob is programmed. The scan tool must stay connected until all of the transmitters are programmed.
Install a scan tool and navigate to the BCM Module Setup menu.
Select Program Key Fobs.
Follow the scan tool on-screen directions.
When the programming operations have completed, operate the transmitter functions to verify correct system operation.

Aug 09, 2017 | 2005 Chevrolet Colorado

1 Answer

Just had 03 l200 bcm repaired at aes how do i get it to work now


Any PCM, BCM, or ignition switch assembly that's replaced requires what's described as a Passlock re-learn procedure to synchronize the three subassemblies for proper operation. This either takes place at Saturn or during a 30-minute DIY procedure in three 10-minute cycles. The procedure is basically to leave the ignition ON for 10-minutes, cycling the ignition OFF and then ON for another 10-minutes and once more until repeated three times, never starting at any time. After the third cycle the ignition can be turned to start the engine to confirm that all components have successfully been synchronized. A failure to start means an incorrect re-learn procedure was done and needs to be repeated all over again. The security light will flash during the process and eventually turn off altogether as indication of successful re-learing security codes for any new part replaced. What isn't changed are the VIN and mileage that Saturn equipment can do. The security system is divided into three parts; the ignition switch sensors, the PCM, and the BCM. Any one of these subassemblies being replaced requires the BCM to relearn the new replacement part otherwise you'll just have a dead engine unable to run. New BCM's come as blanks that Saturn address' with their Techtool II with VIN and mileage copied from the failed BCM. 'Field' BCM's removed from vehicles still retain VIN and mileage that can only be changed by Saturn. There may be other programmed accessories that have to considered to be compatible to the original one removed for replacement.

key remotes

Replacing the BCM will require the remotes to be reprogammed. The problem is that you need a scan tool with the proper software to perform the programming. Here is the procedure for reprogramming if you have access to a tool. If not you should put a call into a local garage that does diagnostic work or the dealer. If it were just a battery change you could resync without programming.

Jul 14, 2012 | 2003 Saturn L-Series

1 Answer

Nissan sentra 2006 My trunk wont open && I spent 2 1/2 hrs trying to break in from the back seats. trying to reach the seat release but cant. The key or remote wont open it. The car latch wont open...


does the key turn the trunk lock?if not theres one issue right there.the other may be that the valet lever on trunk latch assy. may have inadvertantly been engaged if deck lid was slammed closed.the release solenoid will make noise when activated by fob or lever in car but because of valet being engaged cannot release latch.does key unlock glovebox?if not this may also be a valet key cut.contact nissan dealer to cut regular key.ive seen the slamming the deck lid scenario a million times as the valet lever takes hardly any effort to engage.good luck and let me know how you make out.

Feb 07, 2011 | 2006 Nissan Sentra

1 Answer

Replaced battery on my remote control and it does not work. does it needs to be re-programmed again?


Use this Procedure for Vehicles with
Driver Information Center Buttons

This information is in your Owners Manual in the
Drivers Information Center Section.


1. Insert Key and turn to ON position so you can access Driver Information Center

2. Press the vehicle information button until
PRESS TO RELEARN REMOTE KEY displays

3. Press the set/reset button until
REMOTE KEY LEARNING ACTIVE displays

4. Press and hold the lock and unlock buttons on the first keyless remote at the same
time for approximatley 15 seconds. A chime will sound indicating that the remote is
programmed.


5. To program additional remotes at this time repeat step 3.
This vehicle can have a maximum of eight remotes programmed.

6. To exit programming mode turn key off and remove key.
Test remote(s).

Use this Procedure for Vehicles without
Drivers Information Center Buttons

To access this display, the vehicle must be in Park (P) with key in the on position (as far
as you can go without cranking engine)

1. Press the trip odometer reset stem until RELEARN REMOTE KEY displays.
2. Press and hold the trip odometer reset stem for three seconds.
The message REMOTE KEY LEARNING ACTIVE will display

3. Press and hold the lock and unlock buttons on the first keyless remote at the same
time for approximately 15 seconds. A chime
will sound indicating that the remote is
programmed.

4. To program additional remotes at this time repeat step 3.
This vehicle can have a maximum of eight remotes programmed.
5. To exit programming mode turn key off and remove key.
Test remote(s).


Good luck and hope this helps, you may have to reprogram. merry Xmas


Dec 24, 2009 | 2007 Chevrolet Tahoe

1 Answer

Remote start function on remote doesn't work for a 2005 Pontiac G6.


Replace battery first and see if that help, if not then follow steps below, if you cant figure it out or it still doesn't work, or take it to the dealer, it could be remote module is faulty. Keep the windows open as a safety measure, then,

Remove the ignition key from the ignition lock cylinder.

Remove the BCM PRGRM fuse from the fuse panel. Refer to Fuse Block in Wiring Systems.

Close all of the doors.

Close the liftgate.

Turn the ignition lock cylinder to ACC.

Turn the ignition lock cylinder to OFF, & then back to ACC within 1 second.

Open & close any vehicle door. A chime will be heard when the system enters the BCM programming/diagnostic mode.

Important
After 7 seconds, a chime may be heard confirming successful synchronization. It is necessary to wait approximately 14 seconds for a second chime that will confirm successful programming.


Press & hold the transmitter LOCK & UNLOCK buttons simultaneously for 14 seconds.

Repeat the previous step on each additional transmitter to be programmed.

Remove the ignition key from the ignition lock cylinder.

Install the BCM PRGRM fuse back into the fuse panel. Refer to Fuse Block in Wiring Systems.

Oct 07, 2009 | 2005 Pontiac G6

2 Answers

Keys won,t lock or unlock doors


Use this Procedure for Buick Vehicles "With" Driver Information Center Buttons.

This information is in your "Owners Manual" in the "Drivers Information Center Section."

1. Insert Key and turn to ON position so you can access Driver Information Center.

2. Press the vehicle information button until PRESS TO RELEARN REMOTE KEY displays.

3. Press the set/reset button until REMOTE KEY LEARNING ACTIVE displays.

4. Press and hold the lock and unlock buttons on the key-less remote at the same
time for approximately 15 seconds. A chime will sound indicating that the remote is
programmed.

5. To program additional remotes at this time repeat step 4. This vehicle can have a maximum of eight remotes programmed.

6. To exit programming mode turn key off and remove key. Test remote(s).


Use this Procedure for Buick Vehicles "Without" Drivers Information Center Buttons.

To access this display, the vehicle must be in Park (P) with key in the on position (as far as you can go without cranking engine).

1. Press the trip odometer reset stem until RELEARN REMOTE KEY displays.

2. Press and hold the trip odometer reset stem for three seconds. The message REMOTE KEY LEARNING ACTIVE will display

3. Press and hold the lock and unlock buttons on the first key-less remote at the same
time for approximately 15 seconds. A chime will sound indicating that the remote is
programmed.

4. To program additional remotes at this time repeat step 3. This vehicle can have a maximum of eight remotes programmed.

5. To exit programming mode turn key off and remove key. Test remote(s).

Good Luck !

Mar 25, 2009 | 2005 Buick LaCrosse

1 Answer

Automatic door locks will not work.


you need to take it to the dealer and have them check the bcm for codes.... also have them check to be sure you have the latest software in the bcm.. its possible that you just need a software update... there are several TSB's covering the concern you have..... it can be a very simple fix with software or even a stuck lock switch may need to be replaced... without the proper diagnostic codes being read from the bcm all that can be done is guessing..and that can be expensive...

Feb 02, 2009 | 2005 Chrysler Town & Country

1 Answer

2005 cadillac sts remote transmitter


This is the procedure for a reprogram of the remote's from the factory service manual, if it doesn't work then u may have a receiver issue.
Use this Procedure for Vehicles with
Driver Information Center Buttons

This information is in your Owners Manual in the
Drivers Information Center Section.


1. Insert Key and turn to ON position so you can access Driver Information Center

2. Press the vehicle information button until
PRESS TO RELEARN REMOTE KEY displays

3. Press the set/reset button until
REMOTE KEY LEARNING ACTIVE displays

4. Press and hold the lock and unlock buttons on the first keyless remote at the same
time for approximatley 15 seconds. A chime will sound indicating that the remote is
programmed.


5. To program additional remotes at this time repeat step 3.
This vehicle can have a maximum of eight remotes programmed.

6. To exit programming mode turn key off and remove key.
Test remote(s).


Use this Procedure for Vehicles without
Drivers Information Center Buttons


To access this display, the vehicle must be in Park (P) with key in the on position (as far
as you can go without cranking engine)

1. Press the trip odometer reset stem until RELEARN REMOTE KEY displays.
2. Press and hold the trip odometer reset stem for three seconds.
The message REMOTE KEY LEARNING ACTIVE will display

3. Press and hold the lock and unlock buttons on the first keyless remote at the same
time for approximately 15 seconds. A chime
will sound indicating that the remote is
programmed.

4. To program additional remotes at this time repeat step 3.
This vehicle can have a maximum of eight remotes programmed.
5. To exit programming mode turn key off and remove key.
Test remote(s).

Jan 17, 2009 | 2005 Cadillac STS

1 Answer

1997 venture keyless remote programming


SYSTEM OPERATION

System warning lamp located on top of the instrument panel
Press UNLOCK button once , turns on interior lamps and deactivates alarm (if fitted)
Press UNLOCK button twice w/in 5 seconds unlocks all doors, turns on interior lamp and deactivates alarm (if fitted)
To activate alarm system (if fitted):
Switch ignition OFF
Open driver's door
Press Lock button on remote
Close Driver door
warning lamp will flash when system is activated
Press remote power sliding door button will open sliding door (if fitted) only if unlocked first
Pressing remote panic button:
*Sounds horn intermittently
*Flashes exterior lamps
*Turns on interior lamps
**Pressing panic for the second time OR switching ignition ON deactivates alarm.


PROGRAMMING
Remobe key from ignition switch
Remove the "BCM PRGRM" fuse, from the fuse box
Close all doors
Turn ignition switch to the ACC position
With in 1 SECOND , turn the ignition switch to OFF then back to 'ACC'
(really, with in one second)
Open and close the driver's door. A chime will sound, indicating programming mode activated
Press and HOLD LOCK and UNLOCK SIMULTANEOUSLY untill a chime sounds 2 times ( about 15 seconds)
Repeat this exact procedure for all remotes to be programmed
Remove key from ignition
Refit 'BCM PRGRM' fuse.

4 REMOTES MAXIMUM CAN BE PROGRAMMED

Aug 24, 2008 | 2000 Chevrolet Venture

Not finding what you are looking for?
2008 GMC Yukon Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...