Question about 2001 Daewoo Leganza

1 Answer

2001 laganza cam sensor

Need to find out where the cam sensor is located on the car

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,201 Answers

There is a recall on some of those passenger cars about the cam sensor melting, and causing burning.I would take it to a dealer and see if your car is one of them.If it is, they have to replace it.(no charge). good luck.

Posted on Jan 24, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the cam sensor in a 2002 nissan quest?


HI Chuck! The cam position sensor is inside the distributor on the quest. If the cam sensor has gone bad you need to replace the distributor assembly as it is not servicable. Before replacing the distributor, take the cap off and make sure the rotor is turning when you crank the engine. If it is not then check the timing belt as the distributor is driven by the cam shaft. If the belt is broken the cam shaft will not turn and you could get this code.The cam sensor is located under the plastic cover located under the rotor button

Nov 18, 2016 | Nissan Cars & Trucks

1 Answer

Need to know how many sensor. is on my transmission.. 2003 Pontiac Montana v 6 .. can you show me picture where transmission control solenoid goes?


There are 12 common sensors and 10 internal sensors. The most common that often fail (MAP), (TPS), (CAM), (IGN), (CRANK) MAP is your mass air flow which is located at the beginning of your air intake, TPS is the throttle body position sensor, the CAM is the cam shaft position sensor (transmission), IGN ignition position sensor and the CRANK sensor is located near the bottom driver side front

Oct 26, 2013 | 2003 Pontiac Montana

1 Answer

1999 tahoe crank/cam sensor?


the 5.3 and 6.0 are famous for bad crank sensor. never a problem with cam sensor. the crank sensor is located behind the starter. you need to remove starter to get to it. ther is one bolt holding it in. check the wires going to the sensor because they are so close to the exhaust the get brittle and brake. if the wire is good change sensor and your car will run fine

Mar 21, 2013 | 1999 Chevrolet Tahoe

1 Answer

Poo14 code came up need to locate on truck where the cam sensor is


The exhaust cam sensor is on the right front corner of the cylinder head. (DRIVER RIGHT). To your right of the upper radiator hose.

Jan 01, 2012 | 2005 Chevrolet Colorado

2 Answers

Where is the cam sensor located?


the cam sensor is where the distributor used to be. see pic below

2d76ff1.jpg

Oct 26, 2010 | 1989 Oldsmobile Eighty Eight Royale

1 Answer

Location of cam sensor 2003 jeep grand cherokee v8


Answer
pic_12.gif
pic
REMOVAL - 4.7L
The Camshaft Position Sensor (CMP) on the 4.7L V–8 engine is bolted to the front/top of the right cylinder head (CMP Location—4.7L Engine).

It is easier to remove/install sensor from under vehicle.

Raise and support vehicle.
Disconnect electrical connector at CMP sensor (CMP Location—4.7L Engine).
Remove sensor mounting bolt (CMP Location—4.7L Engine).
Carefully twist sensor from cylinder head.
Check condition of sensor o-ring.
See picture for sensor location.


9347d80.gif

Jul 21, 2010 | 2003 Jeep Grand Cherokee

1 Answer

Location of cam sensor


Cam Sensor is on the top of the Water pump located on the Front Timing cover. the Crank sensor is located rear the engine almost on the flywheel.

May 15, 2010 | 2000 Land Rover Range Rover

2 Answers

2005 ford excursion cam sensor location I need to change the cam sensor and the crank sensors on my excursion and i do not know where they are located


On my 02 Excursion with the 7.3L Diesel, the Cam Position Sensor is located at the front bottom of the engine on the passengers side. There is one electrical pigtail plug that is attached and one bolt holds the sensor in position. It may be located in a similar location on your 05 Ex. I do not know where the crank sensor is located. I hope this helps.

Aug 27, 2009 | 2005 Ford Excursion

1 Answer

Ineed to know the location of the cam sensor on a ford escape 2002 with the 3.0 liter V6 DOHC


SECTION 303-14: Electronic Engine Controls 2002 Escape Workshop Manual REMOVAL AND INSTALLATION Camshaft Position (CMP) Sensor —3.0L (4V) Removal and Installation
  1. Remove the camshaft position (CMP) sensor.
    1. Disconnect the electrical connector.
    1. Remove the bolt.
    1. Remove the sensor.
4544c22.gif
#56 is the cam sensor. please rate as fixed if this is what you need.

231ee68.gif

May 02, 2009 | Ford Escape Cars & Trucks

Not finding what you are looking for?
2001 Daewoo Leganza Logo

Related Topics:

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22026 Answers

yadayada
yadayada

Level 3 Expert

69199 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...