Question about Cars & Trucks

Open Question

Want to take drivers door panel off a verada sedan 2004

Need to expose power window mechanism

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1861 Answers

SOURCE: Broken power window mechanism in

Remove the plastic screw covers at the forward edge of the door. Remove the 2 gold coloured screws.
Using a flat blade screwdriver, insert the blade above & below the locking thing at the door handle, pry up and down, top & bottom respectively. Slide & pull the handle out, remove the rod going to the handle.
Remove the 2 big screws for the door panel. 1 is under a small trim cover, the other is under the armrest
Remove the lower light & unplug it (if you have one) which may be under the arm rest (it pops out)
Press the centers of the 2 round push clips that are on the rear edge of the door panel and pull the clips out
Remove any screws at the bottom of the door panel (if you have them)
Starting at the bottom of the panel pull straight out with steady, even pressure as to not snap the plastic clips. After the bottom & side clips are disconnected from the door, lift the top of the panel straight up.
Remove the plastic sheet that covers the inner shell of the door.
Uning a 10 millimeter socket, remove the bolts that holds the window onto the regulator
Remove the window, up & out thru the top of the door
Unbolt & replace the regulator.

Posted on Sep 16, 2008

Ad
  • 82 Answers

SOURCE: driver side power window stopped working

The door panel is held on by plastic clips and 5 screws. 3 screws are on the bottom and 1 in the pull cup and 1 in the inner door handle.Then grab one of the corners and give a small tug, when you get some of the clips to pop out then proceed around the whole panel. To replace the panel take the clips out of the door with a fork and slide them back into the panel and then line it up on the door and use your hand like a hammer and bang the panel back on. Hope this helps

Posted on Jan 12, 2009

  • 42 Answers

SOURCE: 1991 Nissan Maxima: Removal of front driver side door panel

This is out of my haynes manual
1 disconnect negative battery cable
2 on manual window equipped modesl remove the window crank using a hooked tool to remove the retainer clip.
3 on power window equipped models pry out the armrest switch control plate and disconnect the electrical connections
4 detach the armrest pull handle retaining screw then remove the inside door handle trim bezel
5 insert a wide putty knife, a thin screwdriver or a special trim panel removal tool between the trim panel and the head of the retaining clip to disengage the door panel retaining clips.then remove the remaining door panel retaining screws at the lower edge of the door panel.
6 once all of the clips are screws are disengage detach the trim panel disconnect any electrical connectors and remoe the trim panel from the vehicle by gently pulling it up and out.
7 for access to the inner door remove the door panel support bracket then peel back the watershield taking care not to tear it. it install the trim panel first press the watershield back into place. if necessary add more sealant to hold it in place.
8 installation is the reverse of removal

Posted on Mar 20, 2009

countrysi248
  • 443 Answers

SOURCE: I need to remove the door panel on my 2004 Avalanche

There are plastic clips that hold the door panel inplace .. First look for any hidden screws near the door handle . there might be a little plastic cover that you need to remove with a small screw driver to find the screws.. look under the handle also to see if there are any hidden screws . next take a flat blade screw driver and start at the bottom corner and try gently prying the door panel off . try to stay close to the plastic clips not to damage them by prying real hard .. once you have snapped them loose all the way around .. lift up on the door panel to remove it from around the window lip and out it should come.. holler if you have any problems.. usually The mirrors on the chevys are up above the panel and there is a triangle plastic cover over it on the inside .. it will pry off also gently and there are 3 nuts there that need to be removed .. use caution these fall behind the door panel ... holler if you need more. Jerry

Posted on Apr 24, 2009

  • 1986 Answers

SOURCE: door panel removal for 2002 9-5 on driver rear

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls

Posted on Sep 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fuse for power windows


In the I/P - instrument panel fuse box PWR WDO 25amp circuit breaker . This supply's B+ voltage to the master window switch (drivers door ) This is the same for coupe or sedan . Do you know where the I/P fuse box is located ?
Fuse Block - I/P-On the left end of the tie bar .Open the drivers door an at the very end of I/P there is a access panel ,that is the fuse box .
n8qy+jc3ozdrqaaaabjru5erkjggg==

Dec 18, 2015 | Cars & Trucks

1 Answer

Nissan maxima 2004 power lock sticking unable to unlock the car with the remote or the internal switch. some doors will unlock but the driver side and front passenger will not. sometimes the rear door are...


If you live "up north", I would be suspecting rust or corrosion inside the door mechanisms.
You should be needing to take all 4 door panels off, all the whilst remembering that the clips holding the door panels on may be plastic and are very easily broken.
You might need to take the inside door mechanisms apart and lubricate them.
Be sure to use a lubricant that will not evaporate or wash off with water.
I like silicone grease for this.
God bless your efforts.

Jul 31, 2017 | 2004 Nissan Maxima

1 Answer

2004 chrysler sebring driver window won't go down


you may find the problem is the cut out mechanism inside the door panel,this mechanism cuts the power from the window motor when the window reaches the bottom & when it reaches the top,it may need to be reset or it may be faulty & needs replacing......hope this helps....cheers

Aug 09, 2010 | 2004 Chrysler Sebring

2 Answers

I heard a pop when rolling my power window up. And now it wont roll up at all.


sounds like an electrical short in your door panel. open your door. take your door panel off and look for any crossed wires that may have caused your window motor to short out. you will need a new power window motor if this happened. good luck

Nov 14, 2009 | 2004 Ford F150

3 Answers

2004 grand cherokee jeep power windows and


Check for a 40 amp blown fuse for the BCM this controls those 2 unit. If this checks ok disconnect the BCM module and plug back in this will reset it the BCM is located under the Drivers side kick panel against the firewall. If it work after the BCM reset replace the BCM it will work only temporaraly.

Aug 29, 2009 | 2004 Jeep Grand Cherokee

1 Answer

How do u remove the rear drivers side door panel on an 01 olds aurora?


1. Remove the two visible screws on the hinge side of the door panel 2. Remove the two (or three) visible screws on the latch side of the door panel. 3. Remove the screw in the plastic door pull recess. 4. Remove the door pull recess by extending the door pull (like you are opening the door), lifting the end of the recess that the screw was removed from and pulling the recess forward toward the door hinges. 5. Lift the plastic cap off the screw head in the 'cup' located at the rear of the power window control panel on the door and remove the screw. 6. Lift the power window control panel out of the door panel ( it puts up a fight) and disconect the two power plugs on the bottom of the assembly. 7. Using a stiff putty knife or a similar tool pry the bottom of the door panel from the door, it is secured by several plastic push in thingies. 8. Disconect the light bulb from the lower left hand corner of the door panel by twisting it a half turn and pulling straight out. 9. At this point the panel should be connected to the door at the top of the panel only. 10. There is probably a better technique but I lifted and pryed and twisted the door panel until the fasteners from Hell that connect the top of the panel to the door decided to release the panel (all the while making sure I was gentle enough not to damage the panel or the fasteners). 11. I didn't need to remove the mirror but I did notice a screw head leading to the mirror assembly that was exposed after the panel was removed. 12. While you have the panel removed you might want to lubricate as many mechanisms as you can while you have them exposed.

You can follow these instructions witch are for the front door as they are pretty much the same to undo let me know if you need further assistance ok

Aug 17, 2009 | Oldsmobile Aurora Cars & Trucks

2 Answers

2002 Cadillac Sedan DeVille door panel, how do you remove?


I need to repair power window track cable on my car on the driver's side~
2002 Cadillac Sedan DeVille

Jun 30, 2009 | 2004 Cadillac Deville

1 Answer

Window stuck - 1998 Forester Limited


I installed speakers in my door panels.
Pop up the window controlls unplug switches,
remove plastic screw hiders to expose phillips screws
remove screw from door latch lever
pull out on door panel, then lift up
its not too hard good luck
lowrob77@yahoo.com

Jan 10, 2009 | 1998 Subaru Forester

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...