Question about 2006 Mercury Mariner

1 Answer

Removing tail light assm

How do i get it our after remving the two screws from the tail light it self, in a 2007 Mercury Mariner

Posted by on

  • m3crazyo Jan 23, 2009

    awesome thank you!!

  • porterjim Feb 21, 2009

    Mercury Mariner, 2005. Removed 2 outside screws. by removiing the jack, right side, I can feel two plastic pins that hold the light assy.

    How do I get the pins to release? I'm afraid to apply two much force for fear of breakage.

    Jim P.



1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 716 Answers

From Inside The Trunk Or Hatch Whichever You Prefer. Locate The Panel Or Carpeting. It Will Be Directly Behind Where The Light Is Located Only On The Inside. Remove That Panel And Or Carpet And Youll Find Three Bolts Holding The Unit In Place.

Posted on Jan 23, 2009

  • Michael Fisher
    Michael Fisher Jan 23, 2009

    No Problem If You Need Anything Else Let Me Know.
    Thanks For Using
    Michael Scott



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to reset tire low light on 2010 Mercury mariner

THe light will reset it self the computer will reset but all the tires have to have 32 psi then drive it about 5 miles it will reset if not you have a bad tire sensor usually if you had a tire flat fix that the one that will be bad becusa when the remove it they alway Berkeley the sensor good lucl

Oct 03, 2015 | 2010 Mercury Mariner Hybrid

1 Answer

How to get change tail light bulb

Lift gate up remove the 2 screws on the side of the light housing. The back of the light housing is held in by pin style snap fastner. Two ways 1 grab top and bottom pull hard and fast and hope to pop out both. 2 get a hold of the top and just pop it out turn it out grab and pull (always pull straight or the pins will break)

Nov 11, 2010 | 2005 Mercury Mariner

1 Answer

How do i change the brake bulb for my 2007 mercury mariner? I have already removed the 2 screws on the inside section of the rear tail light lens, but something is keeping it connected on the outside of...

Are you positive that there are only 2 screws? If so give a good push with your thumbs near the ceanter of the assembly it should pop out. If not theres another screw that your missing.

Jul 29, 2009 | 2007 Mercury Mariner Premier 4WD

1 Answer

2006 mercury mariner. stupid tail light assembly.

they are hard to take off sometimes, you are doing it right just keep willing it it will come off, there is 2 gromits that hold it into place might have a little dirt into the plunger.

Feb 22, 2009 | 2006 Mercury Mariner

1 Answer

Hello, i am trying to change the tail light bulb in my 2007 Mariner and i can not get the tail light assemble to fully come out. i have take the two small phillip head screws out and try to pull it out but...

yes it will be a little tough usually there ar retainers that the light sit in on the quarter panels be patient try tapping firmly on the outside of the light at qtr

Jan 23, 2009 | 2006 Mercury Mariner

1 Answer

New symbol on dashboard

It's a low tire pressure warning light. Make sure the tires are properly inflated.

Dec 22, 2008 | 2007 Mercury Mariner Premier 4WD

1 Answer

Replace bulb in 05 Mercury mariner

two screws on the inside and lightly tug the the assembley off the outside of the car. should pop right off.

Nov 18, 2008 | 2007 Mercury Mariner Premier 4WD

Not finding what you are looking for?
2006 Mercury Mariner Logo

Related Topics:

385 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts


Level 3 Expert

77499 Answers


Level 3 Expert

5626 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides