Question about Chrysler PT Cruiser

Open Question

How to get hood prop rod unstuck on pt cruiser

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: attach hood prop rod 2001 Ford Focus

First you will need to get a hood prop bushing from pobably your Ford dealer or you can get one from a salvage yard. You may also need a hood rod attchment. In order to attach your hood rod on. In order to allow your hood to close without the rod interfering with the closing of your hood.This can either be obtained at your dealer or salvage yard. Then you will need a 4or 5 foot poll in order to prop your hood.So that you can place the bushing in and also hood attachment bushing.Both bushings snap right in. You will need to take your hood rod and place it in the hole of the bushing the hood rod should have a short bend at the bottom of it.Like an L or 7 the L shape should seat it self into the bushing.In order to erect the rod to hold the hood up.Or in order to attach it on the hood attachment.Before closing the hood. The hood rod bushing for extending your hood rod.In order to hold your hood up.Goes in the side of the inside frame of the body to the rear of the passenger side of the car again it just snaps in. And the hood rod attachment goes towards the front of the passenger side and it also snaps in.It's located horizontal of the headlight.The hood rod bushing is a 2 sided little round shaped plastic bushing just big enough for your hood rod to fit through.And it is usually white. And your hood rod attachmewnt is usually black.

Posted on Aug 09, 2008

Ad
MrScary66613
  • 1990 Answers

SOURCE: car poblem

This is Either the Water Pump or the Thermostat.

Posted on Jan 15, 2009

  • 234 Answers

SOURCE: tie rod ends replaced/ clutch out

The tie rod ends should not have anything to do with the transmission. Was the car jacked up on the shift linkage?

Posted on Apr 27, 2009

  • 3600 Answers

SOURCE: I need a diagram for my 2002 pt cruiser for the

Your best bet is to go to the auto parts store and they can show you the parts and the price of the parts as well and it costs you nothing to look.

Posted on Nov 09, 2009

  • 5 Answers

SOURCE: 2001 PT Cruiser: How too remove crankshaft pulley 2001 PT Cruiser...

GET A 3 SPOKE PULLEY EXTRACTOR AND SCREW IN THE BOLT BUT IN THE CRANKSHAFT HOLE PUT A MUCH SMALLER SCEW SO YOU WOUNT MESS THE INSIDE UP

Posted on May 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Torque specs outer tie rod 2002 pt cruiser


Tighten it up using 2 spanners as tight as you can .

Sep 11, 2016 | 2002 Chrysler PT Cruiser

1 Answer

My pt cruiser has a bumping noise coming from under the hood when in park or sitting still


Get it on a lift and check the engine mounts, exhaust and then under the hood for loose trunking etc. Look for shiny marks on hoses etc to denote rubbing on something.

Nov 01, 2015 | 2003 Chrysler PT Cruiser

1 Answer

2002 pt cruiser driver door actuator replacement



look inside the door and find the module. take out screws, rods, and wires. swap module. put back together. 2002-pt-cruiser-driver-door-actuator-xrysbksmd4oe40lchygmaasz-4-0.jpg

Dec 20, 2014 | 2002 Chrysler PT Cruiser

1 Answer

Wher can i get a wiring diagram of starter circuit on a 2003 pt cruiser?


At a local repair shop --off their data base

Free --from auto zone site, so i here,don't know
how that works

Jul 17, 2014 | 2003 Chrysler PT Cruiser

1 Answer

I need a diagram for my 2002 pt cruiser for the ball joint and tie rod assembly...


Your best bet is to go to the auto parts store and they can show you the parts and the price of the parts as well and it costs you nothing to look.

Nov 09, 2009 | 2002 Chrysler PT Cruiser

3 Answers

Horn does not work


Where is the fuse for the horn on a PT Cruiser

Apr 09, 2009 | 2006 Chrysler PT Cruiser

1 Answer

Tie rod ends replaced/ clutch out


The tie rod ends should not have anything to do with the transmission. Was the car jacked up on the shift linkage?

Oct 20, 2008 | 2003 Chrysler PT Cruiser

1 Answer

Attach hood prop rod 2001 Ford Focus


First you will need to get a hood prop bushing from pobably your Ford dealer or you can get one from a salvage yard. You may also need a hood rod attchment. In order to attach your hood rod on. In order to allow your hood to close without the rod interfering with the closing of your hood.This can either be obtained at your dealer or salvage yard. Then you will need a 4or 5 foot poll in order to prop your hood.So that you can place the bushing in and also hood attachment bushing.Both bushings snap right in. You will need to take your hood rod and place it in the hole of the bushing the hood rod should have a short bend at the bottom of it.Like an L or 7 the L shape should seat it self into the bushing.In order to erect the rod to hold the hood up.Or in order to attach it on the hood attachment.Before closing the hood. The hood rod bushing for extending your hood rod.In order to hold your hood up.Goes in the side of the inside frame of the body to the rear of the passenger side of the car again it just snaps in. And the hood rod attachment goes towards the front of the passenger side and it also snaps in.It's located horizontal of the headlight.The hood rod bushing is a 2 sided little round shaped plastic bushing just big enough for your hood rod to fit through.And it is usually white. And your hood rod attachmewnt is usually black.

Jul 31, 2008 | 2001 Ford Focus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

111 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...