Question about 1999 Honda Civic

Open Question

HOW TO TIGHTEN POWER STEERING BELT 1989 HONDA ACCORD

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1779 Answers

SOURCE: inatallation 92 honda accord power steering pump

Hey, here's the procedure, disable air bag, if equipped w/ one, disconnect the pump return hose from the reservoir and place the end in a large container. Plug the port in the reservoir. Start the engine and turn the steering wheel lock to lock several times, until fluid stops running from the hose. Turn off engine immediately. Re-attach hose. Disconnect the inlet and outlet hoses at the pump. Remove the drive belt. Remove the mounting bolts/nuts and remove pump.
Install in reverse order. Adjust belt tension,fill ps reservoir and bleed any air from the system (to bleed air from system, fill reservoir, start engine and allow to idle, turn wheel from side to side all the way several times. Shut off, fill if necessary.
. Tighten bolts to : Thru bolt 30 ft lbs., mounting nut 16 ft lbs.

Posted on Dec 30, 2008

Ad
philschneide
  • 448 Answers

SOURCE: attempting to replace power steering pump.

Why are you trying to remove the flywheel? Do you mean the pump pulley? If you loosen the mounting bolt and the adjuster bolt of the pump, it will move so that you can remove the belt. The procedure for removing the pump is as follows:
Clamp the power steering feed hose shut so fluid loss will be minimized when the hose is disconnected.
Disconnect the feed hose and pressure line at the pump. Note the difference between the pressure and the feed hoses; the feed hose is held to the pump with a spring type clamp, and the pressure line has two bolts holding it to the pump body. Cap of plug the line and hose to prevent leakage or contamination.
Note the drive belt tension (you will have to return the belt to your estimate of that tension when you replace the pump).
Remove the pump mounting bolt and adjuster bolt. Remove the pump.
Installation is reverse of removal. Install a new o-ring on the end of the pressure line. Make sure to adjust the drivebelt tension (lever it back to where you estimate it way). Check the power steering fluid level and add some, if necessary, then bleed the power steering system (while the car is running turn the wheels all the way to the right and to the left four or five times).
Hope this is helpful.

Posted on Dec 06, 2009

theautoguy
  • 69 Answers

SOURCE: illustrations of removal of power steering pump on

Here is a good link. Check out the video. Changing the pump is a pretty simple task, especially if you bought the pump with a new pulley. If you only have the pump you will need a pulley removal/installation tool. Check your belts to see if they need replacing because now would be a good time to do it since they have to come off to take off the power steering pump.

http://www.youtube.com/watch?v=5WPLowC6aZo

Posted on Jan 09, 2010

  • 1206 Answers

SOURCE: how to tighten drive belt in my 92 honda accord LX?

if it gets louder when the lights are on that means its the alternator belt,and you will have to look under the alternator there you will find the manual tensioner you have to loosen the mounting bolt in order to tighten it with the long tensioner bolt.

Posted on Apr 04, 2010

Testimonial: "Very helpful. Thanks a lot."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to instsll power sreering oump


I highly recommend YOUTUBE! My daughter actually changed her motor watching youtube videos! Good luck How to Remove Replace Power Steering Honda Accord

Apr 12, 2014 | 1989 Honda Accord 4 Door

1 Answer

Can a 93 honda accord run without a power steering belt?


Don't risk it you will have no power steering best to have mechanic check system out something may be on verge of seizing causing you more damage and $$$$$$

Aug 13, 2012 | 1993 Honda Accord

1 Answer

How do i remove the alternater from my 1991 Honda Accord


In front of your engine where the belts are,You'll see that there's 3 belts. Those belts consists of your power steering,ac and of course...your alternator.. First, you'll have to take your P.S belt off by loosening up two main metric size 14 screws from your power steering pump. Once you've done that, you see the tightening srew head on top of the pump..yeah turn that to the left and you'll have room to move the pump up and down...move it down so that you can have enough room to take the P.S belt off.. Next look at your A/c unit and do the same. Last but not least.....loosen up the two screws from your alternator and move the unit towards the front of the car and remove the belt....Do the opposite to rap it up...Hope this helps!! GL!!

Feb 09, 2011 | 1991 Honda Accord

1 Answer

Screeching noise when I start the car or when I come to a stop. I also noticed that when I turn on the heater it squeals. How do I fix this? It's a manual if that makes a difference. Belt dressing didn't...


Most times, its the power steering belt that causes the problem. Check all the belts for tighness, if you find a loose one, tighten it. Or maybe just replace them? I'd check power steering belt first.

Jan 05, 2011 | 1989 Honda Accord 4 Door

2 Answers

How do i tighten belts on 1997 honda accord?


to tighten the thin belt, loosen the top and then the bottom nuts that go through to the frame. The turn the bolt on top, the closest to the front of the car, clockwise. Then tighten both through bolts up. For the thick belt, loosen the through bolt on the alternator, then turn the long bolt at the bottom, front of car, of alternator clockwise.

Apr 22, 2010 | 1992 Honda Accord

1 Answer

Car over heating. How can I fix the problem?


check coolant level when running,check belt tension. I had an accord ,and the belt would come loose every couple months. And it would overheat everytime,but once I tightened the belt it was ok

Feb 28, 2010 | 1989 Honda Accord 4 Door

2 Answers

93 Accord SE squealing sound when steering wheel is turned


your power steering belt needs to be tightened or replaced. It' slipping, causing the annoying squealing. The more it slips, it 'glazes' the belt, making it easier to slip, resulting in the condition getting worse.

Mar 23, 2009 | 1993 Honda Accord

1 Answer

Inatallation 92 honda accord power steering pump


Hey, here's the procedure, disable air bag, if equipped w/ one, disconnect the pump return hose from the reservoir and place the end in a large container. Plug the port in the reservoir. Start the engine and turn the steering wheel lock to lock several times, until fluid stops running from the hose. Turn off engine immediately. Re-attach hose. Disconnect the inlet and outlet hoses at the pump. Remove the drive belt. Remove the mounting bolts/nuts and remove pump.
Install in reverse order. Adjust belt tension,fill ps reservoir and bleed any air from the system (to bleed air from system, fill reservoir, start engine and allow to idle, turn wheel from side to side all the way several times. Shut off, fill if necessary.
. Tighten bolts to : Thru bolt 30 ft lbs., mounting nut 16 ft lbs.

Dec 26, 2008 | 1992 Honda Accord

1 Answer

Power steering fluid leek on 89 honda accord


Should not be too hard. I have not done one on an 1986 model but I have on a 1983. The principle will be the same.
  • You need to drain the fluid.
  • Disconnect all the pump hoses.
  • Release the pump pivot and adjustment bolts and remove the pump from the vehicle.
Replacement is the reversal of the removal operation.
  • Tighten all the bolts.
  • Adjust the drive belt tension.
  • Fill and bleed the system.
Following the above procedure should get the job done. Take your time doing the job and double check your work at the end of the job. Check for any fluid leeks from the system.

Nov 21, 2008 | 1989 Honda Accord 4 Door

2 Answers

Serpentine belt


Hey there hardrock,
  • Get a 14mm or 9/16" socket and a long handled ratchet or breaker bar.
  • Get the belt around all the pulleys except the A/C compressor or Alternator.
  • The tensioner pulley is near the Alternator toward the center of the engine. It's on a spring loaded arm. Get your socket on the center nut of this pulley.
  • Slowly pull the ratchet toward the center of the engine. The pulley will pivot on the arm allowing you to get the belt on the final pulley.
  • Slowly release the tension.
  • You're done
Mike

Jul 15, 2008 | 1993 Honda Accord

Not finding what you are looking for?
1999 Honda Civic Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...