Question about 2001 Oldsmobile Alero

Open Question

EGR valve on 4 cylinder Alero

Can't find the EGR valve on Olds Alero 2.4 liter 4 cylinder engine

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

toneman2121
  • 775 Answers

SOURCE: 2001 Olds Alero oxygen sensor bank 1 P0135

p0135 indicates bank 1 sensor 1 which is before the cat.

Posted on May 22, 2010

keemo68
  • 1263 Answers

SOURCE: Oldsmobile Alero EGR valve bad

yes you can do it yourself the egr valve is located on the exaust manifold closest to the fire wall unfortunately it has to be replace. it has an electronic lead to it and is vaccum operated to replace it is not a difficult task. the part can be purchased at a Napa or Oreilly's for alot less than at a dealership. just make sure your gasket surfaces are clean for replacement of new gaskets. if you have a code reader than can reset the code that is a benefit however if you do not you have to have a scan tool to reset the code. please rate the solution....thanks

Posted on Sep 19, 2008

  • 74 Answers

SOURCE: olds 2000 silhouette egr replacement

there is no easy way car manufacturers make cars for Assembly not for repair, sorry if this is not what you wanted to hear but its true. that said it may be better to look at it from underneath but please follow all the safety instructions in the owners hand book before going under your car

hope you find this helpful regards JR

Posted on May 30, 2009

  • 14036 Answers

SOURCE: Hose reassembly of a 3400 sfi engine in a 1999 olds alero.

YOU GOING TO HAVE TO GO TO DEALERSHIP.THEY PROBABLY CAN PULL UP YOUR HOSE DIAGRAM ON COMPUTER.BUT THE HAYNES.REPAIR MANUAL DONT SHOW ENOUGH PICTURES.NOW A OLDS ALERO REPAIR MANUAL FROM GM WILL SHOW YOU EVERY THING.BUT THEY ARE EXPENSIVE.OR YOU CAN GO TO AUTO ZONE AND BUY THE CD- ROM ALL DATA DIY.COM.IT WILL PROBABLY HELP YOU FIND HOSE DIAGRAM YOU NEED.

Posted on Aug 18, 2009

roniecon
  • 6826 Answers

SOURCE: how to install a water pump on a 2000 olds alero

Remove the serpentine belt ,and remove the 8mm head bolts from all around the water pump,and then remove the pump.

Posted on Oct 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is my 2000 olds alwero2.4l a free spinning motor


No, the 2.4 liter 4 cylinder is an interference engine.

Sep 04, 2016 | 2000 Oldsmobile Alero

1 Answer

Where is my egr valve?


On a 1995 2.2-liter 4-cylinder engine the valve will be found on the intake manifold with a vacuum hose coming out of it and into the manifold. The valve looks like a mushroom shaped metal component.

Read more: http://www.ehow.com/how_7925077_do-liter-4-cylinder-engine.html#ixzz2cAXIt8W9

Aug 16, 2013 | 1995 Chevrolet Cavalier

1 Answer

I submitted a trouble call on my 99 olds alero 3.4 and my credit card was charged for this and yet i havent recieved any assistance. I did notice that i had entered the wrong email address however i wrote...


p0101 Oldsmobile MAF Sensor Signal Range/Performance
p0341 Oldsmobile Camshaft Position (CMP) Sensor Performance
p1404 Oldsmobile EGR Pintle Position
need to do full diagnosis to pin point mutiple codes cause one component can cause the computer to over compensate and throw up additional trouble codes

Sep 22, 2011 | Oldsmobile Alero Cars & Trucks

2 Answers

I need to know what kind of motor my 2002 alero has.


2.2 liters 4 cylinder in-line front engine with 86 mm bore, 94.6 mm stroke, 10 compression ratio, double overhead cam and four valves per cylinder

Jan 19, 2011 | 2002 Oldsmobile Alero

1 Answer

How hard is it for a shadetree mechanic to replace the manifold absolute pressure sensor on a 2000 4-cylinder Olds Alero? When I bought the part, it says it is an EGR vavle and I remember replacing those...


The EGR valve and MAP sensor are indeed different and unrelated parts. An EGR valve that is stuck open can however cause the system to set a false MAP sensor code due to the loss of vacuum in the intake which will cause the sensor to read low but the engine should run very bad, if at all, when this happens. The MAP sensor is located slightly to the drivers side of the throttle body housing on the front side of the motor and is easy to replace. I'd make sure that your EGR valve isn't stuck open or that you don't have another large vacuum leak that could mimic a faulty MAP sensor before replacing it however. Hope this helps a bit and good luck!

Jul 20, 2010 | 2000 Oldsmobile Alero

2 Answers

What are the 01 alero engine sizes?


2001 Olds Alero engines:
* 2.4 L LD9 I4
* 3.4 L LA1 V6

Good luck (remember rated this).

Jul 09, 2010 | 2001 Oldsmobile Alero

2 Answers

2005 Dodge 1500 code p0404 EGR valve.


The electronic EGR valve and solenoid assembly is attached to the rear of the left cylinder head ,

  1. Remove electrical connector (5) at top of EGR valve solenoid.
  2. Remove tube mounting bolt (1) at intake manifold.
  1. Remove two bolts (4) connecting EGR tube (1) to valve assembly.
  2. Remove gasket located between EGR tube flange and EGR valve assembly.
  3. Remove two EGR valve mounting bolts (5).
  4. Separate valve assembly (3) from engine.
  5. Remove and discard metal gasket located between cylinder head and valve assembly.
INSTALLATION
  1. Clean area at rear of left cylinder head where it joins base of EGR valve.
  2. Clean EGR tube where it joins EGR valve.
  3. Position new gasket between EGR valve and cylinder head.
  4. Position EGR valve to cylinder head. Install and tighten two bolts (5). Refer to Torque Specifications.
  5. Position new gasket between EGR tube flange and EGR valve assembly.
  6. Position EGR tube (1) to side of EGR valve and into intake manifold.
    1. Install EGR tube flange bolt (1) at intake manifold. Tighten bolt. Refer to Torque Specifications.
    2. Connect electrical connector (5) to top of EGR valve solenoid (2).Do a final tightening of two EGR tube bolts (4). Refer to Torque Specifications

Feb 05, 2009 | 2005 Dodge Ram 1500

Not finding what you are looking for?
2001 Oldsmobile Alero Logo

Related Topics:

142 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...