Question about Chrysler PT Cruiser

Open Question

Chrysler PT Cruiser Rear Electric window will go down on its own

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 958 Answers

SOURCE: Replacing Alternator For 2001 Chrysler PT Cruiser (Manual)

this instruction is general for all vehicles. i am sorry that i do not have particularly for your 2001 chrysler PT cruiser.

first, identify the alternator.
remove the fan belt on the alternator,
label and remove all wires that is attached to it.
remove all bolts that is holding it.
remove the old alternator.

do the reverse on installing it.

tnx 4 using fixya,

drcool

Posted on Aug 30, 2008

Ad
66 chrgr
  • 1011 Answers

SOURCE: where is the crank sensor located on 2005 chrysler pt cruiser?

the crank sensor is located on back right side of engine by were the trans. bolts up.is the no start when could or hot?

Posted on Jan 25, 2009

rockitman187
  • 2559 Answers

SOURCE: 2004 chrysler pt cruiser starter motor removal

You may sneak it out with small fingers with out pulling out the starter.

If starter removal is required,Just unhook the battery cables,Remove the 2 bolts holding the starter on.


Please rate this a fixya

Posted on Feb 08, 2009

  • 290 Answers

SOURCE: chrysler pt cruiser fuel filter location?

Under vehicle, center, below seating area, mounted on top of fuel tank, in fuel pump module

Posted on Mar 27, 2009

localwonder
  • 6784 Answers

SOURCE: Change the thermostat on 2002 Chrysler PT Cruiser

Hi, i have put together a step by step guide that will help you with this replacement job. Make sure the vehicle is in a cool state before starting this job.


* Drain some coolant into a clean container until the coolant level is below the thermostat housing.
* Remove the upper radiator hose connection from the thermostat housing.
* Loosen the housing bolts and remove the housing.
* Remove the gasket and scrape it carefully from the surface of the housing and the mounting surface on the engine. If the gasket remains on either of the surfaces, there will probably bea coolant leak after reassembly. Some engines use a rubber O-ring to seal a thermostat housing.
* Compare the size of the thermostat to the old one. They are of different sizes, types, and temperature ratings.
* The temperature rating is stamped on the sensing bulb on the bottom of the thermostat. The temperature bulb faces the block.
* When replacing a thermostat, be sure that the thermostat fits into the groove in the block or outlet housing. If the thermostat is installed upside down, the engine will overheat.
* Install the gasket.
* Reinstall the thermostat housing. Refill the system and run the engine or pressure test to check for leaks.
* When the engine has reached operating temperature make sure the thermostat opens.
* You should be able to see coolant circulating within the radiator.
* Another way of checking thermostat operation is to feel the top of the radiator hose or use a thermometer or multimeter with a temperature probe to confirm that the coolant is warming up.
* If the engine is overheating, but the top hose is still cool to the touch, the thermostat is stuck closed and must be replaced.

NOTE
When a paper gasket is used and the recess is in the thermostat housing, it is a good practice to position the thermostat into the recess and glue the gasket to hold it in place. If it falls out of its groove during installation, the outlet housing can be cracked or a coolant leak will result. Before tightening the water outlet housing, try to rock it back and forth to be sure it is flush. Housings are often cracked during this step.


9c06de2.jpg

Posted on Apr 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the crankcase pressure sensor located in a 2004 Pt Cruiser


Chrysler PT Cruiser crankcase pressure Questions ... - Fixya

www.fixya.com > ... > crankcase pressure > Cars & Trucks > Chrysler
Chrysler PT Cruiser cars & trucks crankcase pressure questions and answers. Ask your ... The oil pressure switch/sensor is located on the rear of the engine block above the right axle I believe. Unless you ... Question about 2004 PT Cruiser.

Nov 24, 2015 | Cars & Trucks

1 Answer

How do i fix 2006 Pt cruiser elect window driver side front


You need to figure out if it is a bad switch, wire, supply voltage, or motor. Then replace the bad part.

Sep 26, 2014 | 2006 Chrysler PT Cruiser

1 Answer

How to remove rear door panel on my 2008 pt cruiser


I think the rear windows are designed to only go down so far as the body design of the rear doors won`t allow them to completely go down. the doors are a different shape than the front doors.

Aug 24, 2014 | 2008 Chrysler Pt Cruiser

1 Answer

Front Passenger window won't go down on 2005 PT Cruiser


Check the switch, swop the switch with the one for the drivers window, if that works it you need a new switch, if not its door card off and test out the motor and power feeds

Jan 05, 2014 | 2005 Chrysler PT Cruiser

1 Answer

2002 PT Cruiser: how to put rear seats down...


There is a button I push at the top of each seat back in my 2001.

May 18, 2010 | 2002 Chrysler PT Cruiser

1 Answer

05 pt cruiser conv. r windows not working after batt died


I have a 2004 Chrysler PT Cruiser Convertiable. Both windows on the driverside will not go down when you open the door. I have replaced the window switch and that is not the problem.

Oct 06, 2009 | Chrysler PT Cruiser Cars & Trucks

2 Answers

How do i remove rear power window switch, and


REAR - SEDAN ONLY
  1. Disconnect and isolate the battery negative cable.
  2. Using a trim stick or equivalent, gently pry at the top of the switch.
  3. Remove switch and disconnect electrical harness connectors. 80d2e1b8.gif

Mar 17, 2009 | 2005 Chrysler PT Cruiser

1 Answer

PT Cruiser 2005 rear window won't move


try wiggling rear switch located behind seat on center counsel .hope this helps it diffently a switch problem.i have one this happend to me

Jan 28, 2009 | 2005 Chrysler PT Cruiser

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

74 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8567 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...