Question about 2004 Chrysler Sebring

Open Question

Engine removal 2004 Chrysler Sebring 2.7 liter

Problems with clearing transmission when pulling motor

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

rockitman187
  • 2559 Answers

SOURCE: 2004 chrysler pt cruiser starter motor removal

You may sneak it out with small fingers with out pulling out the starter.

If starter removal is required,Just unhook the battery cables,Remove the 2 bolts holding the starter on.


Please rate this a fixya

Posted on Feb 08, 2009

  • 12104 Answers

SOURCE: 2004 Chrysler Sebring with engine error code 441,

evap emissions control system incorrect purge flow --the most common chrysler fix for this code is replace leak detection pump /ldp but have it checked first-- other areas are evap lines /canister-- purge solenoid-- vacuum switch

Posted on Oct 21, 2009

  • 61 Answers

SOURCE: 2004 chrysler sebring oil leak

The solenoid blocks are known to leak. You will need to access this under the hood. The cooling lines well need removed from the trans, disconnect the input speed sensor, and remove it using a 1" deepwell socket. Remove the plug on the solenoid block, using an 8mm socket. You will see 3 tenmm bolts on the top of the Sol block. Remove these bolts, then gently pry the sol block off the trans. Using a scraper, remove all old gasket material from the trans case, be careful not to damage it, then thoroughly clean the mounting surface. Install the new Sol Block, with a new gasket, and torque to factory specs, re-install the input speed sensor (torque to spec), install the cooling lines, and reconnect the Sol Block 8mm screw, be sure to TORQUE all to factory spec, failure to do this could result in you damaging the new Sol block, or trans.Make sure to check the fluid level after the repair is complete, and you should have the TCM reset as well. It is fairly labor intensive, and for a first-timer, it will probably take you about 2-3 hrs to do this, provided you have the proper tools. Good luck.

Posted on Nov 17, 2009

01fordeb
  • 1033 Answers

SOURCE: oil sending unit on 2004 chrysler sebring V6

Should be located close to the oil filter. It will screw in like a spark plug. It has a harness plug. Easy to change, save yourself $70 in labor. You will need a fairly large wrench to remove

Posted on Jan 03, 2010

sandman357
  • 236 Answers

SOURCE: 2004 chrysler sebring idle speed is too slow. HOw

why do you want your rpms higher while idling? you don't want them high because your gas bill will reflect that. slow shouldn't matter but if it's dying while on idle it could either be your mass air flow sensor or your fuel filter being clogged

Posted on Mar 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The easiest way to take off a water pump for 2004 Chrysler Sebring


Take it to a garage and say "put a new water pump in this for me".

2004 Chrysler Sebring 2.7Ltr. Water Pump Replacement ...

z? 29:29 https://www.youtube.com/watch?v=ebeXcNmBnnE Sep 19, 2015 - Uploaded by Paul Veltum In this video I'll walk you through replacing the water pump on this 2004 Chrysler Sebring with it's 2.7 ...

2004 Chrysler Sebring Timing Belt Water Pump Before 90K ...

2q==? 13:03 https://www.youtube.com/watch?v=UQHRa28sRkY Nov 25, 2012 - Uploaded by Mastermind Denver This video shows why we at Mastermind Enterprises Auto Repair Shop in Denver recommend replacing the ...

WATER PUMP REPLACEMENT IN CHRYSLER 2.7L ...

9k=? 4:52 https://www.youtube.com/watch?v=z_QrXR2jcb8 Mar 7, 2014 - Uploaded by kzguy2 2008 Dodge Charger 2.7l was in need of a new water pump due to it leaking. ... 2004 Chrysler Sebring 2 ...

2004 chrysler sebring water pump weep hole inspection ...

2q==? 0:15 https://www.youtube.com/watch?v=wzqHaQ40doQ Feb 26, 2014 - Uploaded by Graeme Tolton 2004 chrysler sebring water pump weep hole inspection with borescope. ... 2004 Chrysler Sebring 2.7Ltr ...

Chrysler 2.7L Water Pump Installation Problems - YouTube

9k=? 3:30 https://www.youtube.com/watch?v=h5_VFJ1gCpI Nov 19, 2014 - Uploaded by South Main Auto Repair When I installed this water pump on the 2006 Chrysler Sebring 2.7L I ran into a ... 2004 Chrysler Sebring 2 ...




Feb 15, 2016 | Chrysler Cars & Trucks

1 Answer

Tansmission solenoid


  • It is inside the transmission, attached to the valve body. You have to remove the transmission oil pan and valve body to access.

Mar 16, 2014 | 2004 Chrysler Sebring

1 Answer

2004 chrysler sebring AT Trans prob


have electronic transmission module checked

Sep 08, 2009 | 2004 Chrysler Sebring

1 Answer

2004 Sebring needs new water pump and oil pump


$400.00, the mechanic had to pull the top of the engine off to get to the water pump. 8 hours later, they informed me that they never want to work on a water pump for crysler! Wait till you have to replace the battery.... gonna get rid of our sebring soon! Hope this helps...

Aug 01, 2009 | 2002 Chrysler Sebring

2 Answers

Car wont start and have been told it is the starter, where is the starter located? It is a 2004 chrysler sebring convertable!


The starter is mounetd to the bottom of the engine either left or right of the fly wheel..
Look for the fly wheel.. Really big round gear.. The starter spinns that big gear & turns the motor..
Good luck..
Rate me good ;o)

Jul 09, 2009 | 2004 Chrysler Sebring

1 Answer

2004 sebring timing specs.


check the aic (aux idle air control valve) unplug it and see if it evens out you may have a vac leak please rate -jeff

Aug 02, 2008 | 2004 Chrysler Sebring

Not finding what you are looking for?
2004 Chrysler Sebring Logo

Related Topics:

251 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...