Question about Daewoo Lanos
Window regulator needs replacing. C.D. manual for this repair is a bit confusing as the window can't be lowered and I have never seen a window regulator that is operated by wire cabkes??
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: R & R power window drivers side
I am in the process of doing this now to my 96 Lincoln Towncar. Today I removed the door panel. Hidden scews that attach the door panel are at end end of the door pull strap. The plastic end pieces are removable and each have a screw underneath securing the top of the door panel.
Hidden behind the water shield material at the top of the door are two nuts that retain the top connection of the window lift. I am going to razor cut a straight line through the water shield material to insert a socket to remove the two nuts and then put duck tape over the razor cuts rather that pull the water shield material from the door frame.
Started drilling on the left rivet to detach window from the regulator and quit for the evening.
Have three rivets to drill to detach the pwoer window motor from the door frame.
Two more rivets at the bottom of the door to drill out to detach the lower window regulator from the door frame.
Do not know how I am going to remove the right rivet of the bracket that hold the window yet. Looks like a would need a long drill bit to reach through the door frame to make contact with the rivet.
The replacement rivets that came with my window regulator are to big for my rivet tool. Could end up using nuts and bolts. Sure would make it easier for the next window regulator replacement.
Hope I have some good luck using the drill tomorrow. kkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkddddddddddddddddddddddddddddddddd
Posted on Mar 08, 2009
replacing the window regulator is pretty simple there is no need to go to a maual window all u have to do is take the door panel off and if u will go by the window regulator u can identify whick part u will need to remove and replace its a bolt on item and fairly simple to replace but the part is kinda pricey around 200-300 bucks but if u go to ebay u can buy one for around 80 -100 bucks good luck
Posted on May 17, 2009
THis is common Too common. As I posted before.
As I posted in the Passat questions.
The jetta may slightly differ.
Yes. If your window has fallen down and will not roll up.
99% Chance you car is suffering the Infamous VW plastic clip.
The door panel comes off With a T-10 torx or a Hex (Allen) wrench
that will fit and A large Philips Screw Driver..
Remove the Plastic cover on the inside Door handle.
And the Screw or Screw along the Bottom of the door panel.
Then remove the screws that hold the handle the the door.
They are located behind the Plastic plate you removed with a tiny screw driver earlier... Be careful not the mark up the cover whaytprying it up. It is best to pry from underneath. Where marks if made can not be seen
After the screws are out 4 I believe. The Use of a CLip tool ir best.
For getting behind the panel to pop it off. A screw driver will work.
After all the clips are released. Pull the light at the bottom of the panel down and out. Disconnect it ur push it back thought the hole it came from..
Now you need a 10mm socket, or wrench to remove the 12 bolts that hold the metal plate to the Door. Remove all the 10mm bolts, If the widow has not already fallen in the door. It should be released. By removing the Black 2" plugs. THe loosen the bolts that clamp the window the the arms. DO NOT LOOSEN THEM ALL the way, .
Disconect the all the wiring.. THe Door lock cable,can be a pain.
I think it pulls down,.
Next remove the Metal plate. that is the regulator.
reverse to install
Posted on Jun 26, 2009
Tips for a great answer:
Apr 19, 2013 | 2001 Daewoo Lanos
Sep 25, 2012 | 1998 Toyota Sienna
Jul 09, 2012 | 2000 Daewoo Leganza
Jul 14, 2011 | Daewoo Lanos Cars & Trucks
Jan 20, 2011 | 1999 Daewoo Lanos
Apr 15, 2010 | 2000 Daewoo Nubira
Oct 23, 2008 | 1999 Daewoo Lanos
Aug 31, 2008 | 1999 Daewoo Lanos
Aug 04, 2008 | 1998 Honda Civic
18 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: