Question about 1995 Ford Club Chateau

3 Answers

E40d trans will not shift into 3rd or 4th gear, only rev. 1+2

The transmission shifts smooth into first and second and reverse but will not shift into 3rd or 4th gear. When I let off of the rpms due to not shifting into 3rd gear, the transmission neutrals out. I just replaced the shifting solenoid thinking that that was the problem. No affect.

Posted by on

  • Anonymous Jan 31, 2009

    same problem here...did you find out anything on yours yet??

  • Anonymous Mar 28, 2014

    My audi a3 petrol 1999 model all of a sudden only drives in 3rd and 4th gear and won't go in reverse gear does anybody know what this could be ??

×

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Check or replace your thottle position sensor tps that trans needs to know where the throttle is to shift if it is bad it will do as you say wont shift to third
another telltale is it will act like it goes into lockup when shifting into reverse and stall the engine

Posted on Feb 19, 2011

  • dakotaford Feb 19, 2011

    i posted this more for another who may need to know since it has been a while since you asked

×

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 30 Answers

Code po705 trans gearshift senser or bad ground are open wire tx1 tx2 tx3 tx4

Posted on Feb 11, 2010

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Could you please tell me what was your out come, did you need the transmission rebuilt? My transmission is doing exactly the same! Thank you

Posted on Apr 27, 2016

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 Grand Am Automatic will shift normal from 1-2 but will not shift into 3 or 4.


Worn clutches or solenoid issues if it is an Alison style box.

Apr 02, 2017 | Pontiac Cars & Trucks

1 Answer

1996 gmc jimmy will not shift to 3rd gear


Hi, It may be in LIMP mode.

What is "limp-home mode" ? This is a fault mode in which the transmission either loses electrical power or the PCM deactivates all of the electronics. The transmission will default to max line pressure. The driver will have Reverse and 3rd, with manual 2nd available by putting the gearshift in 2 or 1 (doesn't matter). 1st, 4th, and TCC lockup will not be available. It will not hurt the car to drive it like this for short periods, but use manual 2nd to get the car moving, and be aware that the trans will generate more heat than normal while operating in limp-home mode due to increased torque converter slippage during 2nd gear starts and no lockup in 3rd gear.

Common failures on 4L60E, symptom any possible repair:

Trans shifts into gear harshly, car feels sluggish off the line, No 1st, 4th or TCC lockup available, Manual 2nd, 3rd and Reverse are only available gears, CEL is on: Transmission is either in limp-home mode or has lost electrical power. If there are lots of error codes in the PCM, check the under-hood fuse that powers the transmission, and if it pops again, look for a short in that circuit like an O2 sensor harness touching exhaust. Otherwise, check PCM codes for a particular fault in the transmission causing the PCM to put it in limp-home mode.

No 1st or 4th available; trans shifts 2nd to 3rd by itself in D or OD and locks the converter :ShiftA solenoid failed. Easy fix in the pan. Or a wiring problem from PCM to trans.. or PCM.

Car goes into gear but feels very sluggish like the brakes are dragging, but it will roll easily (starts out in 4th gear), you manually shift to 2 to get it moving, once it's moving you put it back in OD and the car shifts 3rd to 4th on its own and locks the converter at the appropriate time: ShiftB solenoid failed: Easy fix in the pan. Or a wiring problem from PCM to trans.. or PCM.

Trans seems noisy when moving in 1st and Reverse, noise goes away instantly if you shift to N or the trans goes into 3rd gear: Reaction planetary is worn out due to high miles or insufficient lubrication. Not a critical failure, but not a good sign either. R&R sooner rather than later.

3rd gear starts, can manually shift through all gears. When car has been turned off for a bit, then back on it will run normally.: VSS dropoff w/ Hi-stall converter. The rpms are too high, but VSS is showing no movement. Happens after a tire burning take-off. Doesn't store a code, will not throw a CEL (I've heard that it will store a code if it happens 3 or more times). Cure: Reprogram PCM for VSS dropoff -- PCMforLess knows about it.

If you can get the Jimmy for no more then $500.00 and the engine sounds good and body is good, you may want to invest in the repair of the jimmy. Also note that to have a close look at the fuel line along the frame on the drivers side just by the back doors, the line is know to corroded there on all the SUV's

Sep 19, 2010 | 1996 GMC Jimmy

1 Answer

Transmission is shifting hard and slow to pull on a 95 silouette also makes clucking sounds while accelerating


Shift suddenly become very hard. When going from park to either reverse or drive it slams into gear. 1-2 and 2-3 shifts are also harsh. All gears seems to work. Problem may be intermittent: Check TPS for smooth and linear electrical response over the entire range of motion. If not, replace.

Extremely harsh shifts from P or N, normal shifts at WOT: EPC (Electronic Pressure Control) solenoid failed. Easy fix in pan. Fix as soon as possible or hard parts will eventually break.

No 1st or 4th available; trans shifts 2nd to 3rd by itself in D or OD and locks the converter : ShiftA solenoid failed. Easy fix in the pan. Or a wiring problem from PCM to trans.. or PCM.

Car goes into gear but feels very sluggish like the brakes are dragging, but it will roll easily (starts out in 4th gear), you manually shift to 2 to get it moving, once it's moving you put it back in OD and the car shifts 3rd to 4th on its own and locks the converter at the appropriate time: ShiftB solenoid failed: Easy fix in the pan. Or a wiring problem from PCM to trans.. or PCM.


Mar 05, 2010 | 2002 Oldsmobile Silhouette

1 Answer

My GMC has 311632 miles on it. I just changed the 4L60E transmission a few months ago and now it wont shift out of first unless I manually put it in second gear. all the gears from park rev. nuetral works...


The transmission may be in Limp mode. The transmission is on the same fuse as the MAF, O2 sensors and at least one other sensor - if an O2 shorts out, it will blow the fuse and the trans will go into limp-home mode. Be sure the trans has power and the fuse is not blown before doing anything else.

What is "limp-home mode" ? This is a fault mode in which the transmission either loses electrical power or the PCM deactivates all of the electronics. The transmission will default to max line pressure. The driver will have Reverse and 3rd, with manual 2nd available by putting the gearshift in 2 or 1 (doesn't matter). 1st, 4th, and TCC lockup will not be available. It will not hurt the car to drive it like this for short periods, but use manual 2nd to get the car moving, and be aware that the trans will generate more heat than normal while operating in limp-home mode due to increased torque converter slippage during 2nd gear starts and no lockup in 3rd gear.

Trans does not upshift out of first, speedometer reads zero at all times: VSS failure. Easy fix on rear of transmission, but xmember must come out to access VSS.

Car goes into gear but feels very sluggish like the brakes are dragging, but it will roll easily (starts out in 4th gear), you manually shift to 2 to get it moving, once it's moving you put it back in OD and the car shifts 3rd to 4th on its own and locks the converter at the appropriate time: ShiftB solenoid failed: Easy fix in the pan. Or a wiring problem from PCM to trans.. or PCM.

No 1st or 4th available; trans shifts 2nd to 3rd by itself in D or OD and locks the converter : ShiftA solenoid failed. Easy fix in the pan. Or a wiring problem from PCM to trans.. or PCM.

Transmission does not shift automatically, only manually. Swap in a known-good PCM, check wiring, check other sensors such as VSS and TPS.

3rd gear starts, can manually shift through all gears. When car has been turned off for a bit, then back on it will run normally.: VSS dropoff w/ Hi-stall converter. The rpms are too high, but VSS is showing no movement. Happens after a tire burning take-off. Doesn't store a code, will not throw a CEL (I've heard that it will store a code if it happens 3 or more times). Cure: Reprogram PCM for VSS dropoff -- PCMforLess knows about it.

Here are just some of the common things you have described with the issues your transmission has. Good luck and keep me posted.

Dec 22, 2009 | 1994 GMC Sierra

1 Answer

Only runs in 1st and 2nd gear and reverse.


This is a fault mode in which the transmission either loses electrical power or the PCM deactivates all of the electronics. The transmission will default to max line pressure. The driver will have Reverse and 3rd, with manual 2nd available by putting the gearshift in 2 or 1 (doesn't matter). 1st, 4th, and TCC lockup will not be available. It will not hurt the car to drive it like this for short periods, but use manual 2nd to get the car moving, and be aware that the trans will generate more heat than normal while operating in limp-home mode due to increased torque converter slippage during 2nd gear starts and no lockup in 3rd gear.

Trans shifts into gear harshly, car feels sluggish off the line
, No 1st, 4th or TCC lockup available, Manual 2nd, 3rd and Reverse are only available gears, CEL is on: Transmission is either in limp-home mode or has lost electrical power. If there are lots of error codes in the PCM, check the under hood fuse that powers the transmission, and if it pops again, look for a short in that circuit like an O2 sensor harness touching exhaust. Otherwise, check PCM codes for a particular fault in the transmission causing the PCM to put it in limp-home mode.

No 1st or 4th available; trans shifts 2nd to 3rd by itself in D or OD and locks the converter : ShiftA solenoid failed. Easy fix in the pan. Or a wiring problem from PCM to trans.. or PCM.

Car goes into gear but feels very sluggish like the brakes are dragging, but it will roll easily (starts out in 4th gear), you manually shift to 2 to get it moving, once it's moving you put it back in OD and the car shifts 3rd to 4th on its own and locks the converter at the appropriate time: ShiftB solenoid failed: Easy fix in the pan. Or a wiring problem from PCM to trans.. or PCM.

Dec 14, 2009 | 2006 Hummer H3

1 Answer

4L 60E - 2001 k1500 will not shift into 3-4. Oil is not burn't and stifts great into1-2


  • No 3rd or 4th gear: “3-4” clutches are worn out. R&R. The car is safe to drive (in 2) until you can get it fixed.
  • Trans shifts into gear harshly, car feels sluggish off the line, No 1st, 4th or TCC lockup available, Manual 2nd, 3rd and Reverse are only available gears, CEL is on: Transmission is either in limp-home mode or has lost electrical power. If there are lots of error codes in the PCM, check the under hood fuse that powers the transmission, and if it pops again, look for a short in that circuit like an O2 sensor harness touching exhaust. Otherwise, check PCM codes for a particular fault in the transmission causing the PCM to put it in limp-home mode.
  • No 1st or 4th available; trans shifts 2nd to 3rd by itself in D or OD and locks the converter : Shift A solenoid failed. Easy fix in the pan. Or a wiring problem from PCM to trans.. or PCM.
Check to see if your transmission is in the limp mode, which would only give you 2nd, 3rd and reverse gears. No 1st or 4th gear.

Nov 19, 2009 | 2003 GMC Sierra 1500

1 Answer

My e40d from a 96' f150 shifts irratically on 3rd


could be pressure also overdrive switch relly need trans could

Apr 01, 2009 | 1995 Ford Club Chateau

3 Answers

Shifting problem


sounds like it may be either a converter problem or u got some bad clutches in third in the case you need to go to a tranny shop.

Jan 27, 2009 | 1998 Honda Civic

2 Answers

98 Civic Auto Trans Slippage


you need to replace clutch pack for that gear can be ordered seperately from parts store or dealer if you want to save money call peach street auto recycling at 1800-365-2341 for a warrantied used one! also might be time for change trans filter and fluid filter could be slightly clogged but I lean towards clutch pack I replace these alot on Hondas

Dec 12, 2008 | 1998 Honda Civic

Not finding what you are looking for?
1995 Ford Club Chateau Logo

2,903 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

68970 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22026 Answers

Ron Lankford

Level 3 Expert

5383 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...