Question about 1982 Ford F 150

1 Answer

Exhaust manafold gasket

Need to know if there are torque specs for 82 ford f150 300 striaght 6

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 362 Answers

22 to 32 Ft. Lbs. Hope this helps, Dave

Posted on Jan 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the torque specs for head bolts on a 2003 Ford Windstar Van?


When doing such major work, there are other parts that need correct torque and sequence as well. Buy a cheap shop manual from an auto parts store for this info and so much more.

Oct 03, 2016 | 2003 Ford Windstar

1 Answer

What are the torque specs for intake manifold on a 1998 ford windstar


what are the torque specs for the head and intake as well as

www.justanswer.com > Ford
... as well as - 47. Find the answer to this and other Ford questions on JustAnswer. ...Intake Manifold Support to RH Cylinder Head, 40-55 Nm. Degas Tube to ...

infamous windstar 3.8L intake gasket - Car Forums and Automotive ...

www.automotiveforums.com > ... > Ford > Windstar
Feb 24, 2006 - infamous windstar 3.8L intake gasket Windstar Car Forums. ... In fact, I may have torqued them in sequence initially to a lower value and then again to the final value in sequence. ... Using the Ford manifold torque pattern pictures can be misleading. ... '96 through '98 use pretty much the same intake.
Intake torque specs ' FordForumsOnline.comwww.fordforumsonline.com > Ford Tech Forums > Engine & DrivetrainMay 7, 2010 - 2 posts - ‎2 authorsISO torque specs for the intake & plenum for a 98 Windstar...3.8 with the ... Our community is here to help you with any questions you have related to your Ford. ... Lower Intake Manifold to Cylinder Head Bolt 8-12 - (71-106).Torque Specifications - AutoZonewww.autozone.com/.../Ford-Windstar.../Specifications/Torque-...AutoZoneAutoZone Repair Guide for your 2004 Ford Truck Ranger 2WD 2.3L MFI DOHC 4cyl Engine Mechanical Specifications Torque Specifications. ... Ford Windstar 1999-2003 ... Bolts, Main Bearing Bolts, Rod Brearing Bolts, Crankshaft Damper Bolts, Flywheel Bolts, Manifold. Intake, Exhaust ... Vehicle: 2008 Ford F150, 98 Civic.

Dec 21, 2015 | 1998 Ford Windstar

1 Answer

What is the torque specs for brake calipers on a ford explorer sport front calipers


  1. Torque Specs For F250 Caliper Bolts - Diesel Forum - TheDieselStop.com

    www.thedieselstop.com > ... > 1999-2007 General Questions Jan 13, 2009 - 3 posts - ‎1 author
    Does any one know what the caliper bolts torque specs are? ... Disc brake caliper pin bolts - Excursion, F-250/F-350 with Ford and Dana axle ... Torque specs for front brakes
    5 posts
    Mar 12, 2009
    05 F250 brake torque specs please
    6 posts
    Aug 22, 2007
    Brake caliper torque specs
    5 posts
    Jul 14, 2007
    Front brake Caliper Bolt Torque
    6 posts
    Apr 25, 2005
    More results from www.thedieselstop.com

Jul 11, 2015 | 1998 Ford Explorer

2 Answers

2004 ford escape exhaust manifold torque specs?


2b507d0.jpg

Fig. Left side exhaust manifold bolt torque sequence-3.0L engine


22ac5ae.jpg

Fig. Right side exhaust manifold bolt torque sequence-3.0L engine

Both cases, exhaust manifold and new gasket, torque the bolts to 15 ft. lbs. (20 Nm).

Good luck (remember to rate this answer).

Oct 22, 2010 | 2004 Ford Escape

2 Answers

What is the torque specs for a 1998 jeep Cherokee classic straight 6 4.0 liter? I am replacing the head gasket and need to find the lbs of torque. Thank you for any advice, pictures, etc.


Torque sequence ------------------ front | 12 8 4 1 5 9 13 | of | | engine | 11 7 3 2 6 10 14 | ------------------ Final torque must be reached in 3 equal steps Step 1: torque all bolts (except bolt 11) to 110 Ft/Lbs Step 2: torque bolt 11 to 100 Ft/Lbs Recheck final torque in sequence.

  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
  3. Disconnect the hoses at the thermostat housing.
  4. Properly relieve the fuel system pressure.
  5. Remove the cylinder head cover.
  6. Loosen the rocker arms.
  7. Remove the pushrods.

The valvetrain components must be replaced in their original positions.
  1. Remove the intake and exhaust manifold from the cylinder head.
  2. Disconnect the spark plug wires and remove the spark plugs.
  3. Disconnect the temperature sending unit wire, ignition coil and bracket assembly from the engine.
  4. Remove the accessory drive belt(s).
  5. Unbolt and set aside the power steering pump and bracket. Do not disconnect the hoses.
  6. Remove the intake and exhaust manifold assembly.
  7. If equipped with A/C, perform the following:
    1. Remove the compressor and position it aside with the lines attached.
    2. Remove the compressor bracket bolts from the cylinder head.
    3. Loosen the through bolt at the bottom of the bracket.

  8. Remove the alternator.
  9. Remove the cylinder head bolts, the cylinder head and gasket from the block.

Bolt No. 14 cannot be removed until the head is moved forward. Pull the bolt out as far as it will go and suspend in place by wrapping with tape.
  1. Discard the gasket. Thoroughly clean the head-to-block mating surface.
  2. Clean and inspect the cylinder head thoroughly. Refer to the engine reconditioning portion outlined later in this section.

To install:
  1. Coat a new head gasket with suitable sealing compound and place it on the block. Most replacement gaskets will have the word TOP stamped on them.

Apply sealing compound only to the cylinder head gasket. Do not allow sealing compound to enter the cylinder bore.

Oct 08, 2009 | 1998 Jeep Cherokee

1 Answer

Need cylinder head gasket torque specs.


looks like there is special sequence to reassemble and tightening, a quick note replace any bolts that have two punch marks.tighten as follows: x x x x x 10 4 2 6 8 x x x x x 7 5 1 3 9 torque all down to 15 ft lbs torque to 30 ft lbs plus 90 degrees. Good luck!

Sep 18, 2009 | 2000 Ford Focus

2 Answers

Head gasket torque specs


Here you go, I hope this is what you were looking for:

For 1987-94 models, the cylinder head bolts are tightened in 3 progressive steps. Tighten them in the proper sequence as follows:
Step 1: 50-55 ft. lbs. (68-75 Nm) Step 2: 60-65 ft. lbs. (81-88 Nm) Step 3: 70-85 ft. lbs. (95-115 Nm) Let me know if I can assist you with anything else.

Apr 30, 2009 | Ford F-150 Cars & Trucks

1 Answer

Exhaust leak back side of 1992 ford f150 302 v8 engine


its the exhaust manafold gasket or the donut gasket in the exhaust pipe, proably the donut gasket.. its a part you can pick you for about $15.. good luck keith...

Mar 21, 2009 | 1992 Ford F150 SuperCab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

76 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...