Question about 1999 Chevrolet Malibu

Open Question

How to change a blower motor on a 1999 chevy malibu

Diagram of motor

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2039 Answers

SOURCE: wiring diagram for blower motor controls

the resistor is bad its beside the blower motor pierre

Posted on Nov 28, 2008

Ad
StormStrikes
  • 104 Answers

SOURCE: 1999 chevy malibu

That engine does not have a timing belt, it has a timing chain and therefore much easier to work with as it can only go on a certain way, the primary focus being getting the dots on the timing chain sprockets lined up properly.

I believe, with the engine at Top Dead Center on cylinder #1, the dots will be facing each other. That is to say, the do on the cam sprocket will be facing the dot on the crank sprocket.

Posted on Jan 02, 2009

ewashmidas
  • 362 Answers

SOURCE: How to change a heater core in a 1999 Chevy Malibu?

Before starting this job I would get a repair manual. This is not a easy job, 6+ hours for an experienced tech with all of the right tools. And you may have to discharge and recharge the AC system.

Posted on Jan 30, 2009

  • 1 Answer

SOURCE: how to replace headlight bulbs 1999 chevy malibu

Thanks Pierre!

Merci beaucoup!

Everything worked as mentionned. Be carefull with the plastic in the winter. Make sure to use a flat screw driver and get it close to the slider and not on the edge. I cracked one of the tongues. Those L shaped slots are under the plastic cover with the two big plastic plugs that you also remove with the flat screw driver

Pierre Godin, Boissevain Manitoba.

Posted on Feb 10, 2009

  • 9 Answers

SOURCE: looking for instructions or a diagram of how to

1 Disconnect the electrical connector from the blower resistor
2 Remove the blower motor insulating cover screws.
3 Disconnect the electrical connector from the blower motor
4 Remove the blower motor insulating cover.
5 Pull the retaining tab down while turning the blower motor counter-clockwise in order to disengage the blower motor from the heater/ventilation module (case)
6 Remove the blower motor. Install in reverse order.

Posted on Feb 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

99 chevy malibu serpentine belt diagram


There are 2 possible diagrams for your car depending on which engine it has. Both diagrams are listed below:


1999 Chevy Malibu 2.4L
greg_margo_28.jpg





1999 Chevy Malibu 3.1L

greg_margo_29.jpg

Aug 16, 2011 | Chevrolet Chevy Cars & Trucks

1 Answer

I need a layout for the resistor for the a/c fan speed control in a '99 Malibu


I do not have the diagram for you. but i can tell you how to change it! first, its behind glove box. to make things easier remove the glove box. remove insulating pad from underneath glove box, next loosen and slide the ecm to one side. now you can see resistor and blower motor. resistor is beside blower motor. remove wiring to resistor. take out the screws that hold it in. then pull it out of heater box. have a good day !!

May 17, 2010 | 1999 Chevrolet Malibu

1 Answer

Replace blower motor resistor unit on 99 Malibu ?


the blower motor resistor is below glove box. remove panal under box. slide the pcm out of the way, resistor is beside blower motor. unplug wiring, take out screws holding it in then pull straight out to remove.

Jul 10, 2009 | 1999 Chevrolet Malibu

1 Answer

How do I change the blower motor resistor on a 1999 chevy malibu?


There should be maybe two screws and the connector sitting by the blower area. A little awkward but not impossible.

Jul 05, 2009 | 1999 Chevrolet Malibu

1 Answer

Looking for instructions or a diagram of how to install a new blower motor on 1999 chevy silverado


1 Disconnect the electrical connector from the blower resistor
2 Remove the blower motor insulating cover screws.
3 Disconnect the electrical connector from the blower motor
4 Remove the blower motor insulating cover.
5 Pull the retaining tab down while turning the blower motor counter-clockwise in order to disengage the blower motor from the heater/ventilation module (case)
6 Remove the blower motor. Install in reverse order.

Feb 18, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

1999 chevy malibu


That engine does not have a timing belt, it has a timing chain and therefore much easier to work with as it can only go on a certain way, the primary focus being getting the dots on the timing chain sprockets lined up properly.

I believe, with the engine at Top Dead Center on cylinder #1, the dots will be facing each other. That is to say, the do on the cam sprocket will be facing the dot on the crank sprocket.

Jan 01, 2009 | 1999 Chevrolet Malibu

1 Answer

Wiring diagram for blower motor controls


the resistor is bad its beside the blower motor pierre

Jul 10, 2008 | 1999 Chevrolet Malibu

1 Answer

Blower or resistor on 99 malibu?


the resistor gmpartsdirect.com usualy has good diagrams or go to the libruary n get a service book

May 16, 2008 | 1999 Chevrolet Malibu

Not finding what you are looking for?
1999 Chevrolet Malibu Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...