Question about 1998 Cadillac Eldorado

Open Question

Need to replace front bumper 98 cadillac eldorado

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 3 Answers

SOURCE: heater blower motor on 1996 cadillac eldorado

very tight but you can clear the engine just moving some spark plug wires and the vacuum controls (controlled units?) right in front of it. when you get the bolts off the blower fan housing and its free to move you just have to rotate it so the flat part can clear the rear valve cover. do yourself a favor and be sure to isolate the problem to the motor (and not the electrical connections or the computer disabling it for something rediculous like lack of a/c charge) as it's an expensive part for a little motor and worse (around 250 i think) if you need end up replacing the entire fan.

Posted on Feb 19, 2009

  • 45 Answers

SOURCE: location starter on 1998 cadillac eldorado northstar engine

well some people like where it is and some don't! i do on my 1997!, i assume u have a 4.6 engine? if u do the starter is under the intake manifold,on a 4.9 engine it is under the car on the left side facing the car, these can be a paine.,go to your local auto supply store and pick up a auto repair manual for your car,by Haynes,good book to own. the 4.6 starter is not that bad to tackle,hope we helped and good luck to u.

Posted on Mar 09, 2009

emissionwiz
  • 75077 Answers

SOURCE: i have 3 ipc codes what does ipc stand for

IPC stands for Instrument panel control, here is a typical code repair flow chart, this is for example only and has nothing to do with your car..
P083 = 24x signal high.

P107 = Instrument panel control )IPC) to computer (PCM) data problem.

P137 = Loss of Automatic braking system (ABS) to Traction control system (TCS).

What you need to do is CLEAR all these codes from the computer and see which ones return.

Perform this test.

1. Ignition key ON. Engine OFF.

2. Simultaneously push and hold the OFF and WARMER (^) buttons on your climate control panel for 3 seconds and release them.

3. Diagnostic codes such as above will appear with the word HISTORY or CURRENT for each code.

4. The codes will stop when you see PCM?

5. Push and release the HI(^) button and you will see PCM DATA?

6. Push and release the LO(v) button and you will see PCM DATA?

7. Continue to push and release the LO (v) button until you see PCM CLEAR CODES?

8. Push and release the HI(^) button until you see PCM CODES CLEAR.

9. Turn OFF the ignition and wait 3 minutes and try and start the car. If the car starts and the light comes back ON, Turn OFF the car and repeat steps 1 thru 3 and let me know what codes you get and if they are HISTORY or CURRENT.

10. When you see PCM?, Turn OFF ignition key.

11. Let me know what codes you get and if they are HISTORY or CURRENT.



---------- FOLLOW-UP ----------

QUESTION: this is what happen when it did what you told me what to do.
P047 History,P107 History,No IPC Code, P83 History,P137 History, A047 Current, No Sir Codes, T072 History,No Russ, PCM?
ANSWER: You did not follow the directives correctly . If you had, You would NOT have any HISTORY CODES.

Try it again and follow these directives EXACTLY:

1. Ignition key ON. Engine OFF.

2. Simultaneously push and hold the OFF and WARMER (^) buttons on your climate control panel for 3 seconds and release them.

3. Diagnostic codes such as above will appear with the word HISTORY or CURRENT for each code.

4. The codes will stop when you see PCM?

5. Push and release the HI(^) button and you will see PCM DATA?

6. Push and release the LO(v) button and you will see PCM DATA?

7. Continue to push and release the LO (v) button until you see PCM CLEAR CODES?

8. Push and release the HI(^) button until you see PCM CODES CLEAR. WAIT 3 seconds and then proceed to 9.

9. Turn OFF the ignition and wait 3 minutes and try and start the car. If the car starts and the light comes back ON, Turn OFF the car and repeat steps 1 thru 3 and let me know what codes you get and if they are HISTORY or CURRENT.

10. When you see PCM?, Turn OFF ignition key.

Posted on Aug 14, 2009

hdsoft
  • 80 Answers

SOURCE: headlight

Well according to my mitchell manuel you don't have to.here is the procedure.
1. open the hood.
2.Remove the push-pin retainer's that secure the top of the upper facia and grill assembly to the upper tie bar to allow the upper facia and grill assembly to flex forward.
3. remove ther bolt and push-pin retainer that secures the top of the headlight assembly to the upper tie bar.
4. Gently pull the upper facia and grill assembly forward to access the bolt on the inboard side of the headlight assembly
5. Pull the headlamp assembly straight out to disengage the the snap in retainer at the lower outboard back surface of the assembly. Turn the assembly so that the inboard assembly clears the front facia.
6. pull the assembly out and away from the veh.From there you'll be able to access bulbs.
be careful not to touch the bulb with fingers or oil in skin will blow bulb.
Good luck.

Posted on Aug 19, 2009

  • 1 Answer

SOURCE: 2004 CTS Cadillac front passenger turn signal bulb is out.

Actually no you don't. Crank your steering wheel all the way to the right so yo have the maxumum clearance for your hands and arms in the front of the wheel well. Remove the plastic clips that hold the wheel well splash guard and pull it back enough to allow access to the interior of your bumper.
Replace bulbs as needed.
Yes, a jack is nice and makes it a touch easier to access, but I did this in an AutoZone parking lot during a cross country road trip.
5 mins tops to complete.

Posted on Mar 14, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to install front bumper on 1999 cadilac eldorado


have you removed the inner wing lining ? usually held in place by a few bolts/screws , just have a good look around ,may need washing off to get a good look

May 25, 2014 | 1999 Cadillac Eldorado

1 Answer

How to replace a 2001 Cadillac Eldordo front bumper


If you look around on the backside of the bumper, you should be able to find the bolts that hold it on, same with the grill. Look aound the bolts are pretty obvious. Just take out what you need to remove the bumper, a little tugging and pulling on the bumper might help find bolts that are easy to miss.. look around, you will find them.

Dec 15, 2013 | 2001 Cadillac Eldorado

1 Answer

Where is 98 eldorado cadillac 4.6 starter located?


It is located in the valley between the cylinders. You can loosen the throtle body, all the bolts holding the intake manifold and then lift the manifols just enough without disturbing the fuel rail to gain access from the lest side of the car to the right. This can be done with common tools and the gaskets on the manifold and TB can be reused if not damaged.

Jun 12, 2010 | 1998 Cadillac Eldorado

2 Answers

Cadillac eldorado 98 ran out of gas now wont


Change fuel filter, may have pulled some debris from tank into fuel filter stopping it up

Feb 28, 2010 | 1997 Cadillac Eldorado

1 Answer

We replaced the radio in our '98 Cadillac and no door chimes


Did you replace it with a factory radio or an after market one?
If you did the after market one,it's not wired correctly.

Nov 18, 2009 | 1998 Cadillac Eldorado

1 Answer

How to replace battery in 98 eldorado


u need a 13 mm wrench to take off the piece of medal that goes over the battery there is 3 bolts , and a 5/16 box wrench to take off the 2 battery cables

Oct 07, 2009 | 1998 Cadillac Eldorado

1 Answer

Front bumper of 94 cad eldorado slipping on driver side - need to


There are 4 points of attachment for the front bumper. The nose has two long bolts that go through each of the 2 horizontal shock absorbers and screw into clips attached to the bumper reinforcement. You can access each bolt head with a long socket extension inserted in front of the fog lights.

The remaining two points of attachment are on the side of each of the front fenders, they are plastic guides that meet up with groves on the inside of the bumber sides, as you slide the bumper onto the reinforcement bumper, you line up the bumper groves with these plastic fender-mounted guides and you will reach a point where the bumper snaps in place.

I suspect the driver side bumper sliped out of the inner grove (best caes scenario), or the bumper goves cracked or the plastic fender-mounted guide cracked.

Get under the car to take a look, alternatively undo the 2 front nose bolts and remove the bumper, actually not a big job, and you will then be able to assess the problem.

Hope this helps.

Apr 05, 2009 | 1994 Cadillac Eldorado

Not finding what you are looking for?
1998 Cadillac Eldorado Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...