Question about 2005 Acura TL

1 Answer

I cant find a way to remove the brake rotor of my acura tl 2005. They seem to be part of the axes. Any ideas?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Acura Master
  • 329 Answers

Make sure that you removed the 2 retaining screws.

I cant find a way - f5ca4d3.jpg

Posted on Jan 24, 2009

  • alex metro
    alex metro Jan 24, 2009


    (click for full-size)

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Brakes are sticking and hesitating on take off. Heats up and then it gets worse as you barely tap to come to a stop.


Sounds like the brakes caliper pistons may be sticking...also if brakes are worn out...rotors and pads...many noises and symptoms will show up Hope this helps.

Jul 30, 2012 | 2005 Acura TL

1 Answer

WANT TO KNOW HOW TO CHANG ROTORS ON 2000 ACURA INTEGRA GSR


TO CHANGE FRONT BRAKE ROTORS. FIRST YOU NEED TO SAFELY RAISE SUPPORT VECHICLE ON JACK STANDS.MAKE SURE VECHICLE PARKED ON LEVEL SOLID GROUND.YOU NEED TO REMOVE BRAKE CALIPER BOLTS AND THE CALIPER FROM THE KNUCKLE.DONT LET CALIPER HANG BY BRAKE HOSE USE A PIECE OF WIRE TO SUPPORT CALIPER.REMOVE THE DISC BRAKE ROTOR RETAINING SCREWS IF EQUIPPED.IF THE ROTOR WILL NOT EASILY PULL OFF,SCREW TWO 8MM BOLTS INTO THE DISC BRAKE REMOVAL HOLES AND TURN THE BOLTS TWO TURNS AT A TIME TO PRESS THE ROTOR FROM THE HUB.

Mar 19, 2011 | 1996 Acura TL Series

1 Answer

How do i replace rear brake pads? And check condition or rotors?


The piston brake pad assembly is usually held in place by two bolts that face the car. Remove these and tap the assembly off .Hang the assembly from a wire.remove the two larger bolts that hold the rest of the assembly in place and remove the rotor.I would simply replace the rotors with after market rather than bother with the old ones.Replace rotor and larger cage.taking carefull note remove the brake pads and compress the brake piston with a C clamp. They should push back with minimal resistance.Check all brake components at this time including the large pins the brake assembly move back and forth on. Install your new pads and replace all the bits.Good luck.P.S. A digital camera might be helpfull if you haven't done this kind of thing before

Oct 24, 2010 | 1998 Acura TL

1 Answer

Do i really need to flush my transmission fluid and brake fluid on acura 2005 tl? if so when. thanks


If this has never been changed since new DON"T DO THIS!!! It seems that if older transmissions are serviced when old they will tend to slip.. It is a way the dealer gets more money from you in more than one way. ASK ANY TECH

Jun 03, 2010 | 2005 Acura TL

2 Answers

We are looking to tow our 205 acura tl behind ou


I would recommend calling a RV dealer near you and they will know or will know who, you should talk to.

Feb 06, 2010 | 2005 Acura TL

3 Answers

I was quoted $275 to replace the rear brakes on my 2005 TSX. Is that a fair price? I have about 88k miles


That is pretty high. If they replaced the pads(using ceramic pads which are top of the line) replacing rotors and rear brake hardware kit, parts should be about $120 so that means $155 for labor when the job would only take about an hour at the most.

Oct 27, 2009 | 2005 Acura TSX

1 Answer

Cannot get rear rotors off car


make sure the parking brake is off, remove to 2 screws that are holding the rotors. you might have to hit the rotor with a rubber hammer

May 26, 2009 | 2004 Acura TL

1 Answer

2005 Acura tl brake replacement


The Brembos that come on Type S/Manual models wear fast. I've changed them at 20,000 miles. They are expensive also.

Non-Type S/Manual models I have seen go 80,000 miles. The biggest factor on brake wear is how the vehicle is driven.

At 50,000 miles I would have them inspected. Depending on where you go, make sure you get an accurate measurement of both pads (inboard and outboard). 2mm is the service limit and about that time the indicators start making noise, but not always. Most indepent shops are going to sell you brake pads at 4mm. That's another 10,000 miles at least you could have driven on them.

Never replace just the brake pads, resurface or replace the rotors. The uneven surfaces of the rotor will cause your new pads to wear incorrectly and possibly cause brake noise. Most aftermarket pads will cause a squeel.

Sep 12, 2008 | 2005 Acura TL

2 Answers

ACURA 2204 TL


I UPGRADE IT MY TL NON TYPE S ...TO THE O.E BREMBO KIT....TOGETHER WITH THE ROTORS AND BRAND NEW ABS SENSORS.......WHY IS THE ABS ,VSA, ABD BRAKE LIGHT ON??MY ACURA IS

Jul 24, 2008 | 2004 Acura TL

Not finding what you are looking for?
2005 Acura TL Logo

Related Topics:

198 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...