Remove pitman arm 1995 ford f-150 - 1995 Ford F150 Styleside Regular Cab

upper and lower ball joints, left and right tie rod ends, idler arm and possibly by the pitman arm all in the front end. You could have some in your drive shafts

Seems like you are doing what you can. Why not disconnect the pitman from the truck and drop the steering box with the pitman arm on it? Although there is a cost for another pitman arm, you risk damaging the steering box components by beating on parts like the pitman arm that connect to the steering box gears and bearings.

If you are missing work and have extra costs, replacing the pitman arm may be a cheaper alternative.

you will need a pitman arm puller, tie rod separator and a good set sockets(6 point preffered)and some penetrating oil, measure all distances between points before removal,and get the vehicle aligned

This might help to understand the steering linkage: REMOVAL & INSTALLATION Fig. 1: Steering linkage used on the Bronco and 4-wheel drive F-150
Fig. 2: Steering linkage used on the 4-wheel drive F-350
Fig. 3: Steering linkage used on F-Super Duty chassis/cab
Pitman Arm EXCEPT F-SUPER DUTY STRIPPED CHASSIS AND MOTOR HOME CHASSIS

1. Place the wheels in a straight-ahead position.
2. Disconnect the drag link at the Pitman arm. You'll need a puller such as a tie rod end remover.
3. Remove the Pitman arm-to-gear nut and washer.
4. Matchmark the Pitman arm and gear housing for installation purposes.
5. Using a 2-jawed puller, remove the Pitman arm from the gear.
6. Installation is the reverse of removal. Align the matchmarks when installing the Pitman arm. Tighten the Pitman arm nut to 170-230 ft. lbs. (230-312 Nm); torque the drag link ball stud nut to 50-75 ft. lbs. (68-102 Nm), advancing the nut to align the cotter pin hole. Never back off the nut to align the hole.

F-SUPER DUTY STRIPPED CHASSIS MOTOR HOME CHASSIS

1. Matchmark the Pitman arm and sector shaft.
2. Disconnect the drag link from the Pitman arm.
3. Remove the bolt and nut securing the Pitman arm to the sector shaft.
4. Using a 2-jawed gear puller, remove the Pitman arm from the sector shaft. To install:
   
5. Aligning the matchmarks, slide the Pitman arm onto the sector shaft. If the arm won't slide on easily, use a cold chisel to spread the separation. NEVER HAMMER THE ARM ONTO THE SHAFT! Hammering on the arm will damage the steering gear!
6. Install the nut and bolt. Tighten the nut to 220-300 ft. lbs. (298-407 Nm).
7. Connect the drag link.

Tie Rod and Drag Link EXCEPT RUBBERIZED BALL SOCKET LINKAGE

1. Place the wheels in a straight-ahead position.
2. Remove the cotter pins and rust from the drag link and tie rod ball studs.
3. Remove the drag link ball studs from the right-hand spindle and Pitman arm.
4. Remove the tie rod ball studs from the left-hand spindle and drag link.
5. Installation is the reverse of removal. Seat the studs in the tapered hole before tightening the nuts. This will avoid wrap-up of the rubber grommets during tightening of the nuts. Tighten the nuts to 70 ft. lbs. (95 Nm). Always use new cotter pins.
6. Have the front end alignment checked.

RUBBERIZED BALL SOCKET LINKAGE

1. Raise and support the front end on jackstands.
2. Place the wheels in the straight-ahead position.
3. Remove the nuts connecting the drag link ball studs to the connecting rod and Pitman arm.
4. Disconnect the drag link using a tie rod end remover.
5. Loosen the bolts on the adjuster clamp. Count the number of turns it take to remove the drag link from the adjuster. To install:
   
6. Installation is the reverse of the removal procedure. Install the drag link with the same number of turns it took to remove it. Make certain that the wheels remain in the straight-ahead position during installation. Seat the studs in the tapered hole before tightening the nuts. This will avoid wrap-up of the rubber grommets during tightening of the nuts. Tighten the adjuster clamp nuts to 40 ft. lbs. (54 Nm). Tighten the ball stud nuts to 75 ft. lbs. (102 Nm).
7. Have the front end alignment checked.

Connecting Rod RUBBERIZED BALL SOCKET LINKAGE

1. Raise and support the front end on jackstands.
2. Place the wheels in the straight-ahead position.
3. Disconnect the connecting rod from the drag link by removing the nut and separating the two with a tie rod end remover.
4. Loosen the bolts on the adjusting sleeve clamps. Count the number of turns it takes to remove the connecting rod from the connecting rod from the adjuster sleeve and remove the rod.
5. Installation is the reverse of removal. Install the connecting rod the exact number of turns noted during removal. Tighten the tie rod nuts to 40 ft. lbs. (54 Nm); the ball stud nut to 75 ft. lbs. (102 Nm).
6. Have the front end alignment checked.

Tie Rod Ends RUBBERIZED BALL SOCKET LINKAGE Fig. 4: Remove the cotter pin from the castellated nut at the ball stud
Fig. 5: Remove the nut from the ball stud
Fig. 6: Use a tie rod end puller tool to remove the ball stud from the Pitman arm
Fig. 7: Liquid correction fluid makes excellent paint to mark the threads of the tie rod end
Fig. 8: For a more accurate reinstallation, you may measure the tie rod end prior to removal
Fig. 9: After having loosened the nut, unscrew and remove the tie rod end

1. Raise and support the front end on jackstands.
2. Place the wheels in a straight-ahead position.
3. Remove the ball stud from the Pitman arm using a tie rod end remover. NOTE: Optional: paint a mark or measure the length of the tie rod end threads to ease reinstallation in as close to the original position as possible.
   
4. Loosen the nuts on the adjusting sleeve clamp. Remove the ball stud from the adjuster, or the adjuster from the tie rod. Count the number of turns it takes to remove the sleeve from the tie rod or ball stud from the sleeve. To install:
   
5. Install the sleeve on the tie rod, or the ball in the sleeve the same number of turns noted during removal. Make sure that the adjuster clamps are in the correct position, illustrated, and torque the clamp bolts to 40 ft. lbs. (54 Nm).
6. Keep the wheels facing straight-ahead and install the ball studs. Tighten the nuts to 75 ft. lbs. (102 Nm). Use new cotter pins.
7. Install the drag link and connecting rod.
8. Have the front end alignment checked.

The pitman arm seal can be replaced by removing the pitman arm, prying out the old seal and driving in a new one. However, usually when the seals start to leak it's from a bad bearing or excessive play in the steering box.

yes you will have to remove the pitman arm and turn the gear box so that it turns more to the right. it has slots so align it on the next slot to the right. they make a tool that they call a pitman arm puller that raps around the pitman arm and puts pressure on gear box shaft wile turning it clock wise. you'll figure it out once you see the tool. the big nut usually takes 1 1/4 inch socket. hope this helps

Once you have the arm removed (use a puller made for that) You need to remove the c clip retainer. Many times you can loosely install the arm, put it back on the ground and with a catch pan under it, just quickly turn the wheel and pressure will drive the seals out. If that does not work, you can use long self tapping screws and put one into each side of the seal and pull it free. Most i've seen always have two seals separated by a steel flat washer. To re-install, you need to carefully drive the seal back in using a piece of pipe or anything that fits and does not damage it. I have special tools I made long ago to do that but the trick is to be careful not to get the seal too far in on any one side and to not damage it in any way. Likely someone makes an install tool. Make note of the order of the seals as you remove them and make a reference mark on the arm and shaft so you can get back together the same way it was.

• here ya go

you may have to extend the steering shaft , other problems may be binding of the u-joint in the shaft.

Good Luck !!

remove the nut then buy a pitman arm puller at your local autoparts store, this tool will pull the pitman arm from the steering box.