Question about Mitsubishi Montero Sport

Open Question

Where is the crankshaft position sensor on a 99 montero sport 3.0

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
keemo68
  • 1263 Answers

SOURCE: is it possible to adjust a throttle position sensor on a 2000 montero sport?

when your vehical throws a code and you replace the defective part, you must clear the code or the ecm will still recognize it as an active code.

Posted on Aug 27, 2008

Ad
  • 1596 Answers

SOURCE: Crankshaft Position Sensor and Camshaft Position Sensor

REMOVE OR DISCONNECT

  1. Serpentine belt from the crankshaft pulley.
  2. Raise the vehicle on a hoist.
  3. Right front tire and wheel assembly.
  4. Right inner fender access cover.
  5. Using a 28 mm socket, remove the crankshaft harmonic balancer retaining bolt.
  6. Crankshaft harmonic balancer using tool J 38192 or equivalent.
  7. Sensor electrical connector.
  8. Foreign object deflector.
  9. Sensor and pedestal from block face.
  10. Sensor from pedestal.
INSTALL OR CONNECT:

  1. Loosely install the crankshaft sensor on the pedestal.
  2. Position the sensor with pedestal attached on special Tool J 37089.
  3. Position the special tool on the crankshaft.
  4. Bolts to hold the pedestal to the block face, torque to 20-40 Nm (14-28 lb.ft).
  5. Torque the pedestal pinch bolt to 3-4 Nm (38-40 lb.in).
  6. Remove special tool J 37089.
  7. Place the special tool 37089 on the harmonic balancer and turn. If any vane of the harmonic balancer touches the tool, replace the balancer assembly.
  8. Balancer on the crankshaft.
    • Apply thread sealer (GM 1052080) or equivalent to the threads of the balancer bolt.
  1. Torque the crankshaft bolt to 140 Nm + 56°(104 lb.ft + 56°).
  2. Foreign object deflector.
  3. Electrical connector.
  4. Inner fender shield.
  5. Tire and wheel assembly, torque to 140 Nm (104 lb.ft).
  6. Lower the vehicle.
  7. Serpentine belt.

Posted on Jun 02, 2009

  • 6982 Answers

SOURCE: 1999 jeep cherokee sport it wont start cranks but wont fire

Figures...I'd use 2&3 as b&c Open reading means that with the meter set to ohms and turned on, the meter should read the same connected to the terminals as it did before you connected it.

Posted on Oct 29, 2009

  • 5 Answers

SOURCE: My 1996 Jeep Cherokee Sport dies or will not start when hot.

Sounds like the ignition coil is getting bad.

Posted on Jan 16, 2010

  • 75 Answers

SOURCE: Instructions for changing our the Crankshaft

On this model you have to follow the directions as if you are changing the timing belt. Within this process, you will actually take out and replace the crankshaft position sensor. You can go to your public library and get the information to change out the timing belt.

Posted on Jan 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the crankshaft position sensor located on the 2002 Mitsubishi Montero sport xls 3.5 truck.


Hi David, The link below is how to test the crank sensor (1997-2004 3.0l Montero, Hope this helps......CHEERS
http://easyautodiagnostics.com/mitsubishi/3.0L/crankshaft-position-sensor-test-1#3
The crankshaft position (CKP) sensor is located behind the timing belt... but testing it is done without removing the timing belt or its components. This is due to the fact that the crank sensor's connector is located on top of the engine and in plain view (next to the ignition control module). In the photo below, the orange arrow points to the location of the crankshaft position sensor connectors (photo applies to: 3.0L 1997-2004 Montero Sport).

Mar 31, 2016 | Mitsubishi Cars & Trucks

1 Answer

Is the starter and flywheel for a '99 compatible with a '93?


Mitsubishi Montero Sport Complete Engines ' eBay

www.ebay.com/sch/Mitsubishi-Montero-Sport...Engines/.../i.html
eBayFind great deals on eBay for Mitsubishi Montero Sport Complete Engines in ... 99-00Mitsubishi Montero Montero Sport 3.5L Engine Motor Assembly 133K Miles ..
Same engine?

Sep 24, 2015 | Mitsubishi Montero Cars & Trucks

1 Answer

Where is the crank sensor located on 1999 montero sport


Crankshaft position sensor A (24x) is behind the crankshaft pulley.

Crankshaft position sensor B (7x) is on the lower back side of the engine block.

May 12, 2014 | 1999 Mitsubishi Montero Sport

1 Answer

What is the tdc for a 99 montero sport


TDC stands for "Top Dead Center". This is where the piston in #1 cylinder is at the very top of it's travel and it has nowhere to go but down. This actually occurs on EVERY revolution of the crankshaft. For engine timing purposes, most repair procedures also expect the valves for #1 cylinder to be completely closed. This happens on every SECOND revolution of the crankshaft. The valves are controlled by the cam shaft. The vehicle manufacturer provides marks on the crankshaft and cam sprockets and on the engine to indicate the crankshaft and camshaft position where this occurs. Please see the picture below.



dttech_75.gif

May 15, 2011 | Mitsubishi Montero Sport Cars & Trucks

1 Answer

Need to replace the crankshaft position sensor


REMOVAL & INSTALLATION
  1. Disconnect the negative battery cable.
  2. Remove the serpentine drive belt from the crankshaft pulley.
  3. Raise and safely support the vehicle.
  4. Remove the right front wheel and tire assembly and the right inner fender access cover/splash shield.
  5. Using a 28mm socket, remove the crankshaft harmonic balancer retaining bolt.
  6. Remove the crankshaft balancer, using a puller if necessary.
  7. For 1992-99 vehicles, remove the CKP sensor shield. Fig. 1: If so equipped, remove the crankshaft position sensor shield 89634g95.gif

  8. Unplug the sensor electrical connector.
  9. For 1987-91 vehicles, perform the following:
    1. Remove the sensor and pedestal from the block face.
    2. Remove the sensor from the pedestal.
  10. For 1992-99 vehicles, remove the sensor from the block face. To install:
    1. For 1987-91 vehicles, perform the following:
    2. Loosely install the crankshaft sensor on the pedestal.
    3. Position the sensor, with the pedestal attached, on crankshaft sensor installation tool J 37089 or equivalent.
    4. Install the bolt to hold the pedestal to the block face, then tighten to 14-28 ft. lbs. (20-40 Nm). Fig. 2: Position the crankshaft sensor tool on the crankshaft 89634g76.gif
      Fig. 3: Insert the crankshaft sensor tool into the harmonic balancer 89634g75.gif

    5. Tighten the pedestal pinch bolt to 30-35 inch lbs. (3-4 Nm).
    6. Remove the special tool.
    7. Place the crankshaft sensor tool on the crankshaft balancer and turn. If any vane on the harmonic balancer touches the tool, replace the balancer.
  11. For 1992-99 vehicles, install the CKP sensor on the block.
    1. Install the retaining bolts and tighten to 14-28 ft. lbs. (20-40 Nm).
    2. Install the crankshaft position sensor shield.
    3. Attach the sensor electrical connector.
  12. Install the balancer on the crankshaft.
  13. Tighten the crankshaft bolt to 200-239 ft. lbs. (270-325 Nm) for 1987-91 vehicles. For 1992-99 vehicles, tighten to 110 ft. lbs. (150 Nm), plus an additional 76┬░rotation.
  14. Install the inner fender shield and the right tire and wheel assembly.
  15. Carefully lower the vehicle.
  16. Install the serpentine belt.
  17. Connect the negative battery cable.
prev.gif next.gif

Oct 29, 2010 | 1999 Oldsmobile 88

1 Answer

Where is the crankshaft sensor located on the dodge dakota 99 sport v6


On the V6 and V8 engines, the crankshaft position sensor is bolted to the cylinder block near the rear of the right cylinder head.

2e977ab.jpg

Jul 30, 2010 | 1999 Dodge Dakota

2 Answers

Where a part is


LOOK ON LOWER SIDE OF CYLINDER BLOCK.

Jul 04, 2010 | 1997 Mitsubishi Montero Sport

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...