Question about Volkswagen Cars & Trucks

Open Question

Remove steering column housing on VW caddy - Volkswagen Cars & Trucks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: Steering Columin Housing

GM has a technical service bulletin regarding this. They just replaced a part in my steering column and the rattle is gone.

Posted on Nov 24, 2008

  • 30 Answers

SOURCE: how do I remove and replace the steering column of 1992 ram 250 v

remove coupling from top of steering rack ( make sure you mark postition of coupling first with centre punch so the replacement will be in the same position)
remove covers from steering column and ignition + anything else attached to column. good luck

Posted on Jul 28, 2009

  • 7 Answers

SOURCE: how do you remove the tilt wheel handle on the

I use a screwdriver and pry it out. It just pops into place. Pry out horizontally and it should come right out.

Posted on Sep 11, 2009

bbbman78
  • 680 Answers

SOURCE: have to remove steering column cover, what kind of fasteners insi

Nothing fancy. Just a standard socket set, and a phillips screwdriver. Unscrew the knee bolster to gain access to the two 10mm bolts along the column (top) everything else is pretty evident. Nothing extreme.

Posted on Apr 10, 2010

elix0411
  • 3530 Answers

SOURCE: how to remove ingition housing

Welcome to Fixya

Thank you for bringing up the problem to our attention. To serve you better, could you please provide me the exact year model of your car.

Your response will be greatly appreciated.

Thank you for using Fixya!

Posted on Aug 26, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ignition switch removal/replacement for 1995 vw passat


Disconnect the negative battery cable. Remove the steering wheel, and then remove the steering column covers. Remove the turn signal and wiper switches. Disconnect the ignition switch wiring. Remove the clamping washer, spring and contact ring from the steering column, and then remove the lock housing up off the column tube and steering column. Remove the ignition switch mounting fastener and remove the switch. Installation is in reverse order of removal noting the following: Press the contact ring, spring and clamping washer onto the steering column using a properly sized and sturdy metal pipe or tube. If after installation of the clamping washer, the steering column is not projecting out far enough, pull the steering column out further.

Jan 23, 2013 | Cars & Trucks

1 Answer

Vw caddy power steering not working


Check the drive belt to the power steering pump. If it is ok, it could be servo pump not supplying enough oil, all of this is mechanical. May also have something to servo compensator, but I unfortunately can not give any advice. Good luck

Nov 25, 2012 | Volkswagen Caddy Cars & Trucks

2 Answers

Fuse box diagram for 2005 vw caddy


its under steering column ,25amp fuse top row in middle of fuse board no 47 numbers are tiny at bottom of each fuse ,, had to replace mine 2009 reg caddy

Feb 13, 2012 | Volkswagen Caddy Cars & Trucks

1 Answer

How do i remove an ignition in a gmc jimmy 2000 without a key?


Hello, Dan. First, disconnect the negative (-)/ground on the battery Dan are you mechanically inclined. If not then don't attempted this job.

You will need to remove all the plastic covers on the steering column. Remove the horn ring.--two screws under the steering wheel. Remove the horn ring and disconnect the horn plug. Remove the steering wheel nut. Use a steering wheel puller to remove the steering wheel.

Remove the turn signal switch that fit around the upper part of the steering column. Then remove the some of the parts that are associated with the steering wheel and/or column.

Now, look at the ignition switch flange, it a big chunk of aluminum. Now look for a large aluminum dowel pin 5/8" in diameter that is driven into the chuck of aluminum but it is parallel to the steering column.

This aluminum dowel pin will have to be drill out before you can get ignition housing off, If there is adjustable steering column lever, remove this also.

Now, once the dowel pin has been removed, looking for a **** in the ignition housing. Take chisel and insert into this ****, drive the chisel into the **** until the ignition housing is loose to be remove by sliding it up over the steering column.

If you buy a new ignition switch, on purchase the switch with keys. Don't buy the hole new ignition housing.. If you do it will get expensive.

In the ignition (old) housing drive out the ignition switch pins that keeps the ignition switch in the housing. Install the new ignition switch re-insert the ignition switch hold pins.

I am fairly sure that Carquest/ NAPA some other larger auto parts will have ignition housing bolt. If they try to sell you a replacement aluminum dowel pin don't buy it. It is almost impossible to install the aluminum dowel pin without the proper tools, so use a bolt to squeeze ignition housing together.

Before putting everything back together. Now, check the new ignition switch to make sure it works. I wish you lot of luck. GB...stewbison

Sep 27, 2011 | 2000 GMC Jimmy

1 Answer

How to change 1999 VW cabrio ignition lock cylinder. How do I get the cylinder out of the aluminum housing?


autozone.com has a free repair guide, see below

printpage_icon.gif


REMOVAL & INSTALLATION

1990-94 Cabriolet,1990-93 Fox, 1990-92 Golf and Jetta


0900c15280267f2b.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Lock cylinder drill point.

  1. Disconnect the negative battery cable.
  2. Remove the steering wheel, then remove the steering column covers.
  3. Remove the turn signal and wiper switches.
  4. Disconnect the ignition switch wiring.
  5. On some models, the hole in the lock body for removing the ignition lock cylinder was not drilled by Volkswagen. To make the hole, use the following measurements in conjunction with the illustrations. Drill the hole where "a" and "b" intersect on the lock body. The hole should be drilled 0.19 inch (3mm) deep
  6. Remove the lock cylinder by pushing a small drill bit or piece of wire into the hole and pulling the cylinder out. It might be easier to insert the ignition key, turn it to the right a little and pull on it.

To install:
  1. Insert the lock cylinder into the housing with the key in the cylinder.
  2. While gently turning the key side-to-side, press the cylinder in to the stop. It should click into place.
  3. Temporarily fit the steering wheel onto the splines, then make sure the column locks and unlocks smoothly.
  4. Install the switches, column covers, wiring and the steering wheel.
  5. Connect the battery cable.

1995-99 Cabrio, 1993-99 Golf and Jetta
  1. Disconnect the negative battery cable.
  2. Center the steering wheel.
  3. Remove the air bag.
  4. Remove the steering column switches.
  5. If the vehicle is equipped with an automatic transmission, detach the shift lock cable from the lock cylinder housing.
  6. Remove the adapter sleeve from the steering column.
  7. Remove the spring and horn contact ring from the steering column assembly.
  8. Detach the sheer bolt.
  9. Insert the ignition key and unlock the cylinder, then detach the wiring connectors.
  10. Once all wiring has been detached, slide the housing off the steering column.
  11. Mark and drill the lock cylinder as shown and described in the above procedure.
  12. Compress the stop spring and pull the lock cylinder out of the steering column housing.
  13. Put the new lock cylinder into the steering lock housing.
  14. Insert the key into the lock cylinder.
  15. While you gently turn the key, insert the lock cylinder fully into the housing.
  16. The rest of the installation procedure is the reverse of removal.


NOTE Always use a new shear pin when installing the lock cylinder.

Oct 08, 2010 | 1999 Volkswagen Cabrio

1 Answer

How to replace the multifunction switch of a 2006 Dodge Ram


REMOVAL
WARNING: To avoid serious or fatal injury on vehicles equipped with airbags, disable the Supplemental Restraint System (SRS) before attempting any steering wheel, steering column, airbag, seat belt tensioner, impact sensor, or instrument panel component diagnosis or service. Disconnect and isolate the battery negative (ground) cable, then wait two minutes for the system capacitor to discharge before performing further diagnosis or service. This is the only sure way to disable the SRS. Failure to take the proper precautions could result in accidental airbag deployment.

1. Disconnect and isolate the battery negative cable.
2. Remove the screw (2) that secures the tilt steering column knob (1) and remove it from the tilt actuator (3) on the left side of the column.
3. From below the steering column, remove the two outboard screws that secure the upper column shroud (1) to the lower shroud (3).
4. Using hand pressure, press inward on both sides of the upper shroud above the parting line of the lower shroud to release the snap features that secure the two shroud halves to each other.
5. Remove the upper shroud from the lower shroud and the steering column.
6. Remove the one center screw that secures the lower shroud to the steering column (4).
7. Remove the lower shroud from the steering column.
8. Disconnect the wire harness connector (2) from the back of the multi-function switch housing (1).
9. Rotate the steering wheel far enough to access and remove the two screws (4) that secure the switch to the multi-function switch mounting housing (3).
10. Grasp the switch control stalk and pull it toward the left side of the vehicle to remove the switch from the mounting housing.

INSTALLATION
1. Slide the multi-function switch (1) into the multi-function switch mounting housing (3) from the left side. Be certain that the alignment pins on the top and bottom of the switch are properly engaged in the channels of the mounting housing.
2. Rotate the steering wheel far enough to install and tighten the two screws (4) that secure the switch to the mounting housing. Tighten the screws to 2 N·m (20 in. lbs.).
3. Reconnect the wire harness connector (2) to the back of the switch housing.
4. Position the lower shroud (3) onto the steering column (4).
5. From below the steering column, install and tighten the one center screw that secures the lower shroud to the steering column. Tighten the screw to 2 N·m (20 in. lbs.).
6. Position the upper shroud (1) onto the steering column over the lower shroud. On vehicles equipped with an automatic transmission, be certain to engage the gearshift lever gap hider into the opening in the right side of both shroud halves.
7. Align the snap features on the upper shroud with the receptacles in the lower shroud and apply hand pressure to snap them together.
8. Install and tighten the two outboard screws that secure the upper shroud to the lower shroud. Tighten the screws to 2 N·m (20 in. lbs.).
9. Position the tilt steering column knob (1) onto the tilt adjuster actuator (3) on the left side of the steering column, then install and tighten the screw (2) to secure the knob to the actuator. Tighten the screw to 2 N·m (20 in. lbs.).
10. Reconnect the battery negative cable.

Sep 14, 2010 | 2006 Dodge Ram 1500

1 Answer

Need to replace the ignation switch in my 2000 chrysler LHS


Removal & Installation
  1. Disconnect negative cable from battery.
  2. Remove the Instrument Panel Center Bezel, Chrysler and Dodge.
  3. Remove side trim panel to steering column cover.
  4. Remove the screws that secure the steering column cover to the instrument panel and relocate panel.
  5. Pull the steering column cover rearward at the top and right side of the cover to release the snap retainers from the instrument panel.
  6. Remove the screws that secure the instrument panel steering column cover reinforcement to bracket and remove reinforcement from the vehicle. Remove the 2 front mounting nuts.
  7. Remove the lower mounting nut.
  8. Slide the assembly rearward into the instrument panel and down to gain access to switch.
  9. Disconnect the electrical connector from the ignition Switch and SKREEM Module.
  10. Remove the interlock cable by depressing the locking tab and pulling straight.
  11. Remove ignition switch mounting screw.
  12. Squeeze the 2 locking tabs to remove ignition switch from the lockhousing .

485d77a.gif
Removal and installation of the ignition switch

To install:

NOTE A tab on the ignition switch indexes to a notch in the lock cylinder housing. Also, a slot in the end of the ignition switch fits over the shaft in the end of the lock cylinder housing.


  1. Use the ignition key to rotate the lock cylinder to align the ignition switch with lock cylinder housing.
  2. Insert ignition switch into lock housing until locking tabs are seated into openings on lock housing.
  3. Install ignition switch mounting screw.
  4. Install the interlock cable into the switch assembly. Attach electrical connector to SKREEM Module.
  5. Install switch assembly into Instrument Panel.
  6. Attach electrical connector to ignition switch.
  7. Tighten the 2 mounting nuts.
  8. Tighten the lower mounting nut.
  9. Install steering column reinforcement.
  10. Steering column reinforcement installed.
  11. Install the Steering column reinforcement cover.
  12. Install trim panel end.
  13. Install the Bezel cluster.
  14. Install the ignition switch bezel ring.
  15. Connect the negative battery cable.

May 28, 2010 | 2000 Chrysler LHS

1 Answer

How do you change an ignition switch on a 2002 VW beetle


This is for the requested item:

Removal & Installation
  1. If necessary, make sure you have the radio code.
  2. Place the steering wheel in the center (wheels straight ahead) position.
  3. Disarm the SRS system, as outlined in the Chassis Electrical System.
  4. Make sure the negative battery cable is disconnected.
  5. Remove the steering wheel, as outlined in this section.
  6. Remove the upper and lower steering column switch trim. Refer to the Turn Signal (Combination) Switch or Multi-function switch procedure for details.
  7. Disconnect the multi-pin connector from the ignition/starter switch.
  8. Remove the locking fluid (paint) from threaded holes of screws.
  9. Loosen the two screws slightly, and pull ignition/starter switch out from steering lock housing in direction shown.

d997782.gif
Remove the locking fluid (paint) from threaded holes of the screws (A). Loosen the two screws (A) slightly, then pull the ignition/starter switch out from steering lock housing in direction of the arrow


To install:
  1. Push the ignition/starter switch into steering lock housing.

    NOTE When installing the ignition/starter lock switch ensure that the ignition/starter lock switch and the lock cylinder are in the same position, e.g. "ignition on".

  2. Tighten screws and seal securing holes with sealant D2.
  3. Connect multi-pin connector to ignition/starter switch.
  4. Install steering column switches, steering wheel trim and steering wheel, as outlined in this section.

Mar 06, 2010 | 2003 Volkswagen New Beetle Convertible

1 Answer

Ignition switch replacment


Ignition Switch REMOVAL & INSTALLATION The ignition switch is located at the bottom of the ignition key cylinder body. To remove the ignition switch, first remove the ignition lock cylinder.

1993–99 Golf and Jetta
  1. Disconnect the negative battery cable.
  2. Center the steering wheel.
  3. Remove the air bag.
  4. Remove the steering column switches.
  5. If the vehicle is equipped with an automatic transmission, detach the shift lock cable from the lock cylinder housing.
  6. Remove the adapter sleeve from the steering column.
  7. Remove the spring and horn contact ring from the steering column assembly.
  8. Detach the sheer bolt.
  9. Insert the ignition key and unlock the cylinder, then detach the wiring connectors.
  10. Once all wiring has been detached, slide the housing off the steering column.
  11. Mark and drill the lock cylinder as shown and described in the above procedure.
  12. Compress the stop spring and pull the lock cylinder out of the steering column housing.
  13. Put the new lock cylinder into the steering lock housing.
  14. Insert the key into the lock cylinder.
  15. While you gently turn the key, insert the lock cylinder fully into the housing.
  16. The rest of the installation procedure is the reverse of removal. NOTE: Always use a new shear pin when installing the lock cylinder.

Jun 25, 2009 | 1998 Volkswagen Jetta

1 Answer

Steering column removal procedures on a 1994 grand am manual trans with tilt steering.


  1. Remove Air Bag Disconnect battery ground cable and remove left instrument panel sound insulator, lower trim panel or duct assembly, and steering column collar, as equipped.
  2. If column is to be disassembled, remove horn contact pad and steering wheel
  3. Push back seal to expose flexible coupling, then remove coupling pinch bolt.
  4. Remove lower column support bracket bolt, then the upper bracket to instrument panel support bolts and lower column.
  5. Disconnect column electrical connectors and shift indicator cable, if equipped.
  6. Disconnect shift cable at actuator and housing holder, then remove steering column.
d502e56.jpg

Dec 03, 2008 | 1994 Pontiac Grand Am

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

191 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75077 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...