Question about 2005 Toyota Corolla

1 Answer

Brake problem toyota carina e "94

Brakes get stuck,like i'm braking when driving for long periods of time,when i open the bleeder it releases and is fine for another while !!!!!

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,118 Answers

Sounds like break hose is not letting fluid run back to resavor. have you done a break job lately and maybe kinked a line. break lines ar two way, fluid to caliber and returns to resavor thru same line. you also might have a caliber sticking.

Posted on Jan 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My rigth side front brake is locking the wheel off while driving and the brake is applied


most common cause would be a bad disk brake caliper, or bad brake hose.

the way to find out witch one, is to jack up the front of the car and put it on jack stands. put the transmission in neutral. then turn the front wheels one at a time and wile turning the wheel have some one apply the brake the wheel should stop turning immediately and then wile applying pressure on the wheel have the person in the car release the brake pedal the brake should release immediately if not, then open the brake bleeder on the offending caliper if the brake releases then. you have a bad brake hose if the brake still does not release with the bleeder open then you have a bad brake caliper.

GOOD LUCK

Mar 16, 2011 | 1992 Honda Accord

1 Answer

How do u bleed the clutch on a 1985 toyota celica


See instructions below from autozone.com. If the clutch still has air after following this procedure, try back bleeding by pushing the slave piston in while the bleeder is open, then closing bleeder before releasing the piston. This is similar to bench bleeding the slave, in case you didn't do that before the installation.


HYDRAULIC SYSTEM BLEEDING This operation must be performed any time the clutch master or slave cylinder has been removed or if any of the hydraulic lines have been opened.

WARNING Do not spill brake fluid on the bodywork of the vehicle; it will destroy the paint. If fluid is spilled, immediately wash the surface with plenty of clean water.

  1. Fill the master cylinder reservoir with brake fluid.
  2. Remove the cap on the bleeder screw on the clutch slave cylinder. Install a clear vinyl hose on the fitting; place the other end submerged in a clear glass jar partially filled with brake fluid.
  3. Have an assistant pump the clutch pedal slowly several times. After several pumps, hold the pedal down and open the bleeder, allowing fluid to flow into the jar. Close the bleeder valve almost immediately after opening it. Release the pedal only after the bleeder is closed.
  4. Repeat the process until the fluid in the hose contains no air bubbles. tube. When there are no more air bubbles in the system, tighten the plug fully with the pedal depressed. Replace the plastic cap.
  5. Fill the clutch master cylinder reservoir to the correct level with brake fluid.
  6. Check the system for leaks.

Nov 02, 2010 | 1985 Toyota Celica Supra

1 Answer

Trying to bleed brake line, no success with pumping brakes. Two people , one pumping brakes the other bleeding. Not getting air or fluid.


It sounds like you may not be doing the process corectly. If you are, then I apologize. Make certain that the bleeder valve is in the closed position. Have another person pump the break peddle much in the same sequence as CPR (if that helps). Upon your command, the other person needs to apply steady pressure to the brake peddle until you tell him to release, and not before. While he is applying pressure, you, open the bleeder valve. At that time, the peddle should go to the flow. Close the bleeder valve BEFORE you tell him to release the pressure. Repeat the process until all four brake calipers have been bled, (meaning that you get a stream of fluid with no air bubbles.Periodically throughout the process, it is important to make certain that you have plenty of fluid in the reservoir. That should do it. If not, I'd like to know. Good luck.

Sep 27, 2010 | 1987 Chevrolet El Camino

1 Answer

How to bleed brakes on 2002 toyota sienna


Here is the procedure from the service manual. I would add just one thing. Do each wheel in this order

  1. right rear wheel
  2. left rear wheel
  3. right front wheel
  4. left front wheel
BLEEDING

HINT: If any work is done on the brake system or if air in the brake lines is suspected, bleed the air from the system.

NOTICE: Do not let brake fluid remain on a painted surface. Wash it off immediately.


a)FILL BRAKE RESERVOIR WITH BRAKE FLUID Fluid:SAE J1703 or FMVSS No. 116 DOT3

b)BLEED MASTER CYLINDER HINT: If the master cylinder has been disassembled or if the reservoir becomes empty, bleed the air from the master cylinder.

c)Disconnect the brake lines from the master cylinder. SST 09023-00100 Slowly depress the brake pedal and hold it.

Block off the outlet plug with your finger and release the brake pedal.
Repeat (b) and (c) 3 or 4 times.


BLEED BRAKE LINE

1. Connect the vinyl tube to the caliper or wheel cylinder bleeder plug.
2. Depress the brake pedal several times, then loosen the bleeder plug with the pedal held down.
3. At the point when fluid stops coming out, tighten the bleeder plug, then release the brake pedal. Torque: (Bleeder plug) Front brake caliper
: 8.3 Nm (85 kgf-cm, 74 inch lbs.) Rear wheel cylinder: 8.5 Nm (87 kgf-cm, 75 inch lbs.)
4. Repeat (b) and (c) until all the air in the fluid has been bled out.
5. Repeat the above procedure to bleed the air out of the brake line for each wheel.

CHECK FLUID LEVEL IN RESERVOIR Check the fluid level and add fluid if necessary. Fluid: SAE J1703 or FMVSS No. 116 DOT3

Jun 25, 2010 | 2002 Toyota Sienna

1 Answer

Took my 93' Toyota, has 193,000 miles replaced the


THE MASTER CYLINDER NEED TO BE BLED FIRST.BEFORE PUTTING ON THE CAR.TO MANUAL BLEED BRAKE SYSTEM.YOU NEED 2 PEOPLE TO DO A BETTER JOB.YOU FIRST BLEED THE LEFT REAR RIGHT REAR LEFT FRONT AND RIGHT FRONT. WHEN YOU BLEED THE BRAKES.HAVE THE HELPER PUMP BRAKES 3 PUMPS.AND HOLD BRAKE PEDAL IN.YOU NEED A CLEAR BLEEDER HOSE IN A CLEAR BOTTLE HALF WITH CLEAN BRAKE FLUID. WITH BLEEDER HOSE ON BLEEDER SCREW AND OTHER END BLEEDER HOSE IN BOTTLE OF BRAKE FLUID.WHILE HELPER PUMP BRAKE PEDAL HOLD IT IN OPEN BLEEDER SCREW 1/4 TURN ALLOWING AIR BUBBLES LEAVE THE BRAKE SYSTEM.CLOSE THE BLEEDER SCREW BEFORE BRAKE PEDAL RELEASE.HAVE HELPER PUMP BRAKE PEDAL 3 TIMES. WITH PEDAL HELD DOWN OPEN BLEEDER SCREW GETTING AIR OUT OF THE SYSTEM.WHEN YOU SEE SOLID FLUID COMING OUT OF BLEEDER HOSE THE AIR IS OUT THE BRAKE SYSTEM.DONT DRIVE CAR ON HIGHWAY IF YOU STILL CANT GET SOLID BRAKES. HAVE CAR TOWED IN TO BE PRESSURE BLEED.

Jun 19, 2010 | 1993 Toyota Corolla

1 Answer

When bleeding brakes and loosen off on the bleeder valve on the front brakes for a 1996 chevy blazer v6 4.3l 4x4,do you have to pump the brake pads a number of times until the fluid starts shooting out or...


before you break the bleeder pump the brakes a few times have some one to hold their foot on the brake pedal open the bleeder enough for the fluid to run out once the pedal drops to the floor close the bleeder and have the person pump the brakes back up again. do this on each wheel until you get all fluid out of the bleeder. be sure that the master cylinder stays full during the process and make sure that the brakes are not released while the bleeder is open so as not to pull air into the system.

Dec 28, 2009 | Chevrolet Blazer Cars & Trucks

3 Answers

No brakes after master cyclinder and booster replacment


To bleed the brake system open all the bleeders and let the system gravity bleed for @ 1/2 hour ensuring the master stays full. Then close all bleeders and starting furthest from the master (r/r) have someone pump the brakes 2-3 times,hold the pedal down, then open the bleeder,close the bleeder,and repeat untill there are no air bubbles and the brake fluid is running clear .Repeat for all wheels in this order R/R L/R R/F L/F ensuring master cykinder does not run empty. You cannot pump the pedal with a bleeder open you will be sucking air back into the system. Once you finish all wheels repeat to ensure there is no air remaining in system.

Apr 17, 2009 | Toyota Pickup Cars & Trucks

1 Answer

Toyota carina e brakes


you might have worn out brake pads, make sure to call to an auto repair many offer free brake inspection

May 27, 2008 | 2005 Toyota Corolla

Not finding what you are looking for?
2005 Toyota Corolla Logo

Related Topics:

216 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...