Question about 1988 Mazda 929

Open Question

How to remove dashboard to repair/replace heater core on 1988 mazda 929?

Replacing or repairing heater core in 1988 Mazda 929. Need instructions on how to remove the dashboard.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 75744 Answers

SOURCE: replacing the heater core in

From Haynes Repair Manual #36071, Ford Ranger Pickups 1993 - 2005 and Mazda Pickups 1994-2005 B2300, B2500, B3000, B4000: (1)Disarm the airbag system; (2)allow the cooling system to completely cool down; (3)using a thick cloth for protection, turn the radiator filler cap to the first stop; (4)step back and let the pressure release; (5)once the pressure has been released, completely drain the cooling system; (6) working within the engine compartment, loosen the ****,ps on the heater hoses at the engine compartment side of the firewall, twist the hoses and carefully sepseparate them from the heater core tubes; (7)plug or cap the heater core tubes to prevent coolant from spilling into the passenger compartment when the heater core is removed; (8)place a plastic sheet on the floor of the vehicle to prevent stains if the coolant spills; (9)remove the instrument panel; (10)remove the PCM heat sink and ground strap; (11)remove the heater plenum chamber; (12)separate the heater core from the heater plenum chamber; (13)installation is the reverse of the removal with the following additions; (a)fill the cooling system; (b)run the engine, check for leaks and test the heater

Posted on Aug 21, 2008

junkman1249
  • 552 Answers

SOURCE: need timing belt markings for 1989 mazda 929

check aboutauto.com they might have it

Posted on Mar 30, 2009

pumpkinman
  • 1144 Answers

SOURCE: do you need to remove the dashboard to change the heater core

Go inside engine bay.loolk for the heater blower motor.your heater core is behind that.and it will give you an idea to if its easy gotten to.u usually dont have to remove the dash.just some plastic shrouds.see where your heater hoses go in from engine bay and thats where itll be

Posted on Jun 17, 2009

  • 2002 Answers

SOURCE: need download manual for repair mazda b2000 1988

Check out faxonautoliterature. $69 gets you the original Mazda service manual. I've used them before and they have excellent service. Hope this helps.

Posted on Nov 18, 2009

Testimonial: "Thank you so much, i keep finding for free.. bye"

  • 7353 Answers

SOURCE: need a heater core diagram for a 91 mazda b2200

The only thing to do is get a diagram from the MAZDA dealer parts dept. "A few parts fell out" is way to vague to help you.

Posted on Dec 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace the timing belt on a 1994 mazda 929 3.0 dohc 24 valve engine


Choose:

1994 Mazda MPV timing belt replacement, 6 cylinder DOHC ...

? 3:46
https://www.youtube.com/watch?v=sD2G-NzycvU
Aug 11, 2011 - Uploaded by rsarp
1994 Mazda MPV timing belt replacement, 6 cylinder DOHC 3.0... engine so the valves would not be bent ...

How to replace the timing belt on a 1994 mazda 929 3.0 ...

www.fixya.com/.../t25991928-replace_timing_belt_1994_mazda_929_3...
4 hours ago - how to replace the timing belt on a 1994 mazda 929 3.0 dohc 24 valve... I have a 2000 Mazda 626 4cyl 2.0 liter DOHC engine replacing the timing belt, what ... 2004 6s, 3l. where is the canister purge valve solenoid located?

Where are the timing marks on a 1994 mazda 929 3.0l - Fixya

www.fixya.com/cars/t25991952-timing_marks_1994_mazda_929_3_0l
4 hours ago - where are the timing marks on a 1994 mazda 929 3.0l - Mazda Cars ...1994 Mazda E2000 Cam Timing Mark Positions to Replace Timing Belt ... on a 1994mazda v6 dohc 24 valve engine How to align the timing mark on the ...

Mazda Timing Belt Replacement



Dec 03, 2015 | Mazda Cars & Trucks

1 Answer

I need a picture of the speed sensor and where it is located on a 1988 Mazda 929


most speed sensors are located on the right side of the output transmission of the diff housing

Oct 25, 2014 | 1988 Mazda 929

1 Answer

Need to change spark plugs mazda 929 3 litre 1995


Hi there:I suggest check this for 1995 Mazda 929 3.0 liter DOHC V-6...


5_2_2012_4_10_25_pm.gif

Hope this helps; remember to rated this answer.

May 02, 2012 | 1995 Mazda 929

1 Answer

929 Mazda (1992) No Heat But A/C Works I have a 929 Mazda 1992 year. Does not blow any heat. I noted that the 30 amp fusible link for the heater was busted. Replaced it but still no heat. A busted fuse...


First check your fluid in your radiator if its low your heater will not work. Check all your heater hoses and make sure they are not kinked.
Your heater core may be plugged That will stop the heat flowing as well. If it's the heater core it will have to come out and replaced most likely. Not sure if there is a heater valve on that car.

Mar 05, 2017 | 1992 Mazda 929

2 Answers

Need instructions for replacing heater core


If it is necessary to remove the heater assembly, the cooling system must be drained before removing the heater core.
When a heater core leaks, a new heater core is installed or the old one repaired.
Heater Housing
  • The heater housing is usually under the dash and must be removed to gain access to the heater core.
  • Procedures for replacing the heater core vary with the year, make, and model of car. It threfore necessary to consult the manufacturer's repair manuals for the proper procedure for replacement.
f74-01.gif The heater housing is disassembled to get to the heater core. Heater Core
  • Remove the access panels(s) or the split heater/air conditioning case to gain acess to the heater core.
  • Remove the heater coolant hoses.
  • Remove the cable and/or vacuum control lines (if equipped).
  • Remove the heater core securing brackets and/or clamps.
  • Lift the core from the case. Do not use force. Take care not to damage the fins of the heater core when removing.
  • To reinstall the heater core, reverse the removal steps.
When the heater core leaks and must be repaired or replaced, it is a very difficult and time-consuming job primarily because of the core's location deep within the firewall of the car. For this reason always leak test a replacement heater core before installation.

Dec 28, 2010 | 1997 Mazda Protege

1 Answer

How do i remove the heater core in a 2001 mazda b2500?


Inspect/Replace If it is necessary to remove the heater assembly, the cooling system must be drained before removing the heater core.
When a heater core leaks, a new heater core is installed or the old one repaired.
Heater Housing
  • The heater housing is usually under the dash and must be removed to gain access to the heater core.
  • Procedures for replacing the heater core vary with the year, make, and model of car. It threfore necessary to consult the manufacturer's repair manuals for the proper procedure for replacement.
f74-01.gif The heater housing is disassembled to get to the heater core. Heater Core
  • Remove the access panels(s) or the split heater/air conditioning case to gain acess to the heater core.
  • Remove the heater coolant hoses.
  • Remove the cable and/or vacuum control lines (if equipped).
  • Remove the heater core securing brackets and/or clamps.
  • Lift the core from the case. Do not use force. Take care not to damage the fins of the heater core when removing.
  • To reinstall the heater core, reverse the removal steps.
When the heater core leaks and must be repaired or replaced, it is a very difficult and time-consuming job primarily because of the core's location deep within the firewall of the car. For this reason always leak test a replacement heater core before installation.

Nov 27, 2010 | 2001 Mazda Pickup Regular Cab

1 Answer

How long does it take to replace a mazda b4000


To remove and replace heater core 7.1 hrs
Plus 1.4 hrs to recover a/c system, evacuate and recharge a/c system, if your a/c is working.
These labor time's per Mitchell labor guide, a guide book used by repair shop's.

Jan 26, 2010 | Mazda B4000 Cars & Trucks

1 Answer

Need timing belt markings for 1989 mazda 929


check aboutauto.com they might have it

Mar 30, 2009 | 1989 Mazda 929

1 Answer

Replacing the heater core in 2000 mazda b3000


From Haynes Repair Manual #36071, Ford Ranger Pickups 1993 - 2005 and Mazda Pickups 1994-2005 B2300, B2500, B3000, B4000: (1)Disarm the airbag system; (2)allow the cooling system to completely cool down; (3)using a thick cloth for protection, turn the radiator filler cap to the first stop; (4)step back and let the pressure release; (5)once the pressure has been released, completely drain the cooling system; (6) working within the engine compartment, loosen the ****,ps on the heater hoses at the engine compartment side of the firewall, twist the hoses and carefully sepseparate them from the heater core tubes; (7)plug or cap the heater core tubes to prevent coolant from spilling into the passenger compartment when the heater core is removed; (8)place a plastic sheet on the floor of the vehicle to prevent stains if the coolant spills; (9)remove the instrument panel; (10)remove the PCM heat sink and ground strap; (11)remove the heater plenum chamber; (12)separate the heater core from the heater plenum chamber; (13)installation is the reverse of the removal with the following additions; (a)fill the cooling system; (b)run the engine, check for leaks and test the heater

Aug 21, 2008 | Mazda B3000 Cars & Trucks

3 Answers

Heating / Cooling System Malfunction


all mazda 929 have this problem when the coolant level is dropped
the heater core has no fluid in it since it ts off of the engine block . hence it cannot recive any coolant to heat the car. the best way to fix this is bleed the system of air . when filling coolant squezze the return hose with the cap on the rad it will force fluid bact to the core and push the air out
once you do this a few times you will see the rad fluid droped fill it up and run the car . this should solve this problem

May 15, 2008 | 1994 Mazda 929

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...