Question about Cars & Trucks

Open Question

Wiring diagram for a 2002 ford windstar

No power to the fuel pump

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: i need a 2002 ford ranger fuse box diagram and afuel pump relay switch diagram

Hi

go to www.motorcraftservice.com then click on the owner guide and put in your truck information
then choose the 1st owner manual printing and should be between page # 184 to 200.

Good luck and I hope this will awnser your question.

Posted on Nov 08, 2008

localwonder
  • 6784 Answers

SOURCE: remove fuel pump from tank ford windstar 98

To gain access to the fuel pump, it is necessary to remove the fuel tank.

  1. Depressurize the fuel system and remove the fuel tank from the vehicle.
  2. Remove any dirt that has accumulated around the fuel pump module attaching flange, to prevent it from entering the tank during service.
  3. Turn the fuel pump module locking ring counterclockwise using a locking ring removal tool or a brass drift and remove the locking ring.
  4. Remove the fuel pump module.
  5. Remove the seal gasket and discard it.

To install:
  1. Put a light coating of grease on a new seal ring to hold it in place during assembly. Install it in fuel tank ring groove.
  2. Insert the fuel pump module into the fuel tank, then secure it in place with the locking ring. Tighten the ring until secure.
  3. Install the tank in the vehicle.
  4. Install a minimum of 10 gallons of fuel and check for leaks.
  5. Install a pressure gauge on the throttle body valve and turn the ignition ON for 3 seconds. Turn the key OFF , then repeat the key cycle five to ten times until the pressure gauge shows at least 30 psi.
  6. Check for fuel leaks at the fittings.
  7. Remove the pressure gauge.
  8. Start the engine and check for fuel leaks.

Posted on May 27, 2009

  • 1 Answer

SOURCE: no power to fuel pump or fuel pump wiring harness...

try the electrical ignition switch on the steering wheel colum

Posted on Aug 25, 2009

gandergmm
  • 145 Answers

SOURCE: wiring diagram for ford windstar 1998

i assume its a 3.8L
http://host-comp.com/281774/va102115.pdf

Posted on Sep 30, 2009

  • 270 Answers

SOURCE: power steering pump on a 2001 ford windstar

There is a special tool for that. It should be available at most auto parts stores.

Posted on Oct 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I replaced the fuel filter and the fuel pump but there is still no fuel pressure what else could be wrong with my 2002 ford focus?


either the fuel pump has no power or is disconnected somehow, or you have a fuel leak. Grab some towels and a voltmeter, maybe a wiring diagram, and go fish.

Feb 23, 2015 | 2002 Ford Focus

1 Answer

How to wire a


There are diagrams on the Autozone site after you register your vehicle. Or do a Web search on "1998 Ford Windstar fuelpump wiring".

Hard to know if you are talking about just the rear-end wiring for the tank pump or the whole vehicle. There is a safety device called an Inertia switch which should remain connected. The fuel pump gets power from the front of the vehicle. Once you see the diagram you will see what I mean.

Aug 10, 2014 | 1998 Ford Windstar

1 Answer

2000 ford windstar no fuel changed fuel pump still no fuel changed fuses and relay


Check the power feed for the pump at the fuel pump relay. Pull the relay out, and with a test light clipped to a ground, probe all the terminals that the relay plugs in to. One terminal should be hot at all times. If no terminal has power, either a fusible link off the battery has failed or a maxi fuse has blown-check a wiring diagram to see how the relay gets power to it.
If the relay has power to it, check the other relay terminals with the engine cranking. When cranking the engine, two terminals should have power-the fuel pump feed, and the signal from computer to activate the relay. If both signals are present, check the pump wire from relay to tank, check the fuel pump ground, and check if the coil side of relay has a good ground-signal from computer goes to coil input side, the coil output terminal should go to ground.
Good luck. Post back with what you find.

Oct 17, 2013 | 2001 Ford Windstar

1 Answer

Not enough power to fuel pump


The 7 volts tells you your dropping the other
5.6 volts somewhere

Check the entire circuit with the problem for
voltage drops to ground or poor grounding

Pretty much need a wiring diagram to even
start on it

Feb 28, 2013 | 2000 Ford Windstar

1 Answer

Cruse control wiring diagram for 2002 ford windstar


I am sorry but Fixya has no wiring diagrams of any kind. Ford copyrights these and they are not free to share. You can buy the Ford booklet that contains all wiring diagrams HERE

Jul 03, 2012 | 2002 Ford Windstar Cargo

1 Answer

How do you check if there is power to the fuel pump on 2000 ford windstar. should there be power to the fuel pump shut off switch when checked with a test light?


yes. power comes from the fuel pump relay to that switch then to the pump Of course the wire will only have power in the crank mode, or for 2 seconds when key is turned to ON.

Nov 10, 2010 | 2000 Ford Windstar

2 Answers

99 Ford Windstar. Not getting any power to the fuel pump


first check the fuse if it is good then check for power at the relay

Jan 10, 2010 | 1999 Ford Windstar

1 Answer

Just changed plugs and wires and engine is running rough.


google your make in model and the answer will find you. If it is still there check the timing and fuel filter

Apr 10, 2009 | 1996 Ford Windstar

1 Answer

Wiring diagram


Hello, If you go to google and look up wiring diagram there is a web site that gives you all of the diagrams.  Hope This helps (Please Take The Time To Rate Me)

Mar 15, 2009 | 2002 Ford Windstar Cargo

1 Answer

1996 windstar relay


The fuel pump power on the Windstar is controlled by a component called a Constant Control Relay Module (CCRM).
Its located located on the driver's side of the engine compartment.d7fb0ae.jpg

Oct 22, 2008 | 1996 Ford Windstar

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

80 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...