Question about 1994 Toyota Land Cruiser

1 Answer

HARD PEDAL WHEN BREAKING - 1994 Toyota Land Cruiser

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Night Owl:

    An expert who has answered 10 or more questions between 12 midnight and 6am on the same day.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 14 Answers

Vacume pump on alternator failed or pipe loose to brake servo cylinder,check where you top up brake fluid big round cylinder with plastic pipe to it, pull pipe out and start engine and see if its sucking if not check pipes to pump! either bad connection on pipe or pump failed

HARD PEDAL WHEN BREAKING - 1_26_2013_4_53_52_am.jpg

Posted on Jan 26, 2013

  • David Mills
    David Mills Jan 26, 2013

    its the silver pipe on drawing on cylinder for vac for brake sevo assistance ;)



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What causes gas pedal to go to floor? Will not come back up. 2005 Aviator

Several things the throttle cable breaking allowing the pedal uncontrolled movement or smashing into the football and stAying there or the pedal return spring not functioning due to poor lubrication also cable cabin be affected the same stiff and sticks in place or hard to return to the tick over idle engine
The throttle itself sticking fully open which will hold the pedal down mecanical failed or a combination of factors I'd seek a qualified mechanic to check it out for your own safety

Jul 03, 2016 | Cars & Trucks

1 Answer

When I hit the brake pedal pedal jerks and makes a humming sound what causes

Could be power break system, Could be brake disks or drums, It could be ABS system, a part of the breaking system. Since breaking is critical for safety, I'd get it checked and fixed soon by your dealer or a reputable shop.

Mar 04, 2015 | Cars & Trucks

2 Answers

When breaking, my break pedal begins to pulsate when stopping. Also, the steering wheel begins to shake when breaking.

Usually a sign one of the front brake rotors is out of round. It could also be something wrong with the abs but I doubt it.

Jul 17, 2014 | Dodge Cars & Trucks

1 Answer

Soft brake pedal

bleed the brakes again . start with the rear right wheel then rear left then right front . do it several times and ensure there is no air in the system

Feb 26, 2014 | Geo Prizm Cars & Trucks

1 Answer

My Toyota RAV4 shakes when I apply brakes, especiall going downhill. Do they need to be replaced?

More than likely it's time to replace .Usually if the pedal shakes hard while breaking that signifies that the rotor is bad.Sounds to me as if you will be replacing breaks and rotors.

Apr 10, 2012 | 2007 Toyota RAV4

1 Answer

Hi, I have a 1981 VW jetta diesel. While I was driving, the break pedal started to get stiff. Now the pedal does not depress, it just stays at the top and I have no breaking power. I suspect the master...

Sounds to me like your brake booster is bad. Does the car still stop even though the pedal is hard when you step on it?If so that's most likely it

Jan 06, 2011 | 1983 Volkswagen Jetta

1 Answer

I recently replaced all of the break pads (4 wheels all disc) on my 2004 Hyundai Santa Fe. I have a brake, but the pedal goes down too far before gaining hold/stopping the car. I never cracked a bleeder...

the brakes need to be broken in, if you are pushing the pedal hard to try to stop, if the pedal just goes down on normal breaking then theres a problem, make sure the pads are sliding freely, if the pads are tight on the bracket then the bracket needs to be cleaned and lubed, this will make the pedal drop lower than normal, theres no other reason, you never opened the bleeders the pedal should be good, make sure the pads slide freely,

Dec 05, 2010 | 2004 Hyundai Santa Fe

1 Answer


It sounds like a prob with the cable from the peddle to the intake. Also check the motor mounts! Frankster016

Oct 26, 2008 | 2007 Dodge Caravan SXT Minivan New Cars

2 Answers

Hard pedal low stopping power

First you need to check the brakes lines and the brake pads must be replaced on your car they may be worn out........ Get it checked from the local service center........

May 30, 2008 | 1991 Buick Regal

Not finding what you are looking for?
1994 Toyota Land Cruiser Logo

Related Topics:

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts


Level 3 Expert

78936 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides