Question about Cars & Trucks

1 Answer

Could I use plastic metal bondo for a seal on a hydraulic clutch line

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 124 Answers

No it will not hold the presure you need tos solder or braze it or replace the line

Posted on Feb 27, 2013


2 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 636 Answers

SOURCE: I have nicked the plastic tubing of the hydraulic

you could try some of that puddy similar to JB weld only in a puddy form this sets very quick and is easily applied to a clean surface.

Posted on Sep 09, 2009

Testimonial: "will this not plug up the bore of the plastic tube? used high press. fuel line and 4 clamps. no leaks."

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to bleed cluctch on Nissan tida

On most recent car models the clutch hydraulic system is sealed and not serviceable. The master and slave cylinders and the hydraulic line are sealed at the factory and if a component fails they are replaced as a unit. A low or "weak" pedal may be due to a worn clutch disc or pressure plate. You should have the clutch system inspected to determine what parts need replaced.

May 23, 2015 | Nissan Tiida Cars & Trucks

1 Answer

I drive a 2003 Mitsubishi Lancer OZ Rally. So i downshifted my car and my clutch kinda broke. It is very loose now and when I have the car started i can't shift when I depress the clutch pedal. The car...

I believe you have a sealed hydraulic clutch system. The master or slave cylinder might have failed, or the hydraulic line connecting the two cylinders may have fractured. If the line or the slave cylinder failed you will see hydraulic fluid on the ground under the car. In any event, the system is sealed at the factory when installed and is not serviceable at the component level. If this is the case you will need to purchase the system pre-assembled and replace all three components together. You should also inspect the bell housing and clutch slave cylinder to make sure it has not come loose from the clutch housing. This can also cause the problem you describe.

Feb 26, 2015 | Mitsubishi Cars & Trucks

1 Answer

Clutch line

Yes, you can do it, but it has to be a high pressure line.

Jan 06, 2015 | Cars & Trucks

1 Answer

Clutch master cylinder hydraulic line removal

Need to know year and engine size. I know that the 1999 Dakota 2.5L clutch hydraulic system comes as a pre-charged, completely sealed system including the reservoir, master/slave cylinders and the connecting lines. There is no means of disassembly. If you use aftermarket parts, you must buy the entire aftermarket set and assemble and bleed it.

Jul 22, 2013 | Dodge Dakota Cars & Trucks

1 Answer

My 98 camaro v6 manual hydraulic clutch line keeps disconnecting itself

sounds like the lock on the line is bad or the lock on the slave cylinder is bad they make new broke stuff everday

Oct 18, 2017 | 1998 Chevrolet Camaro

2 Answers

I just replace my front brake lines and when i went to bleed the brakes I saw fluid coming from aline that was going to the back of the jeep. It was along the frame and was plastic JW

There should be NO brake lines that are plastic. What the plastic line may be for is fuel, fuel return or the Evap system.
And I have seen where those lines will devolpe a leak from a pin hole, crack, split, O-rings in the ends.

A manual transmission could also have a plastic line from the clutch master to the clutch slave. So if you have a manual and it was brake fluid you saw leaking from it that could be it as the Hydraulic clutches use brake fluid in the system.

Sep 23, 2011 | 1997 Jeep Grand Cherokee

1 Answer

We are changing the clutch in a 2001 gmc senora. taking out the transmisson, there is a line coming out of the left side that we don't know how it releases. it looks like a oil line of some sort....

That line is your hydraulic clutch line which is attached to the clutch master cylinder. Look very closely, you will see a white plastic sleeve on the metal connector at the transmission end of this hose. you will need to gently push this toward the transmission. you will have to work on many sides as this piece is flexible. Once worked in all around. the line should pull out of the transmission.

Sep 04, 2011 | 2001 GMC Sonoma Extended Cab

2 Answers

Hydrolic clutch fluid comming out of bell housing

you will need to replace the clutch release cylinder

Mar 02, 2011 | 1996 Nissan Maxima

2 Answers

The clutch is stuck to the floor bord and i cant shift

you may have a faulty clutch master cylinder or faulty clutch slave cylinder- leaking clutch fluid. most of the time both are replaced at the same time which should be recomended by your mechanic, the bolts to the master cylinder are very hard to get to and require the right tool.
you should be able to move car forward by selecting 1st then cranking engine till it starts, gear changes while driving are hard but not impossible. i recommend a tow truck to a local repairer.

Dec 22, 2009 | 1995 Isuzu Rodeo

1 Answer

Hilux clutch master cylinder seals which way do the seal or seals face.

The seals face towards the hydraulic side. Install with the wide side of the seal towards the hydraulic line. Note: it will not bleed like a brake system. Fill the resivoir and open the slave bleeder and gravity bleed, that will get you about 90%. Then get somebody to step on the pedal while you ,now, bleed it like a brake system. Good Luck!.

Jun 21, 2009 | 1991 Toyota Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides