Question about Cars & Trucks

1 Answer

The plenum whent bad and the motor locked up. I replaced the plenum and the motor is still locked up, how do I unlock the motor

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 21,873 Answers

Not really following your question here.
The plenium is the top part of the intake. It would not have any direct affect on the crank.
If the engine overheated or ran out of oil the bearings could be stuck - welded in place which would require the engine be taken apart.

Posted on Jan 13, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

On my sorento 2005,the doors will unlock with remote or door button but won`t lock.How can I fix the problem


U can easily fix it.....there can be to things....
- lose screw of locking motor which connect with the lock ...or
- a bad locking motor.....simply replace...



Hope it helps
Regards
Asad

Dec 11, 2013 | 2003 Kia Sorento

1 Answer

How to replace the heater motor in a 1977 f150 with a/c


You will need to remove the glove box for access, then you will be able to see the fan motor. It is possible to remove the motor while the heater plenum is still in the truck, but it makes it a lot easier to remove the plenum then switch out the bad motor.

Nov 17, 2013 | Cars & Trucks

1 Answer

How do you unlock the map sensor to replace it


Unlock it from the plastic upper plenum? Just pull straight up. May help to slip a small screwdriver under it a twist to get it started. It has a ribbed seal on it that holds it in and the parts on the plenum keep it from twisting. They don't lock it in.

Aug 30, 2011 | 2000 Chevrolet Silverado 1500

3 Answers

Driver side door doesn't lock or unlock with the remote. The rest of the doors work fine.


Does the Driver side door lock and unlock from the lock switch inside? If not then you have a bad motor or bad connection to the lock/unlock motor inside the door.

Jan 08, 2010 | 2004 Toyota Camry

1 Answer

My temperature knob on my 2000 silerado will not work it will not cool down to lower heat


The internal Damper Doors within the Heating A/C Plenum are controlled by Stepper Motors. It is possible that one has failed such as is also common in the Instrument Cluster for all rotary Indicators. If you have this repaired I strongly recommend that you have ALL the Stepper Motors inside the Plenum replaced. The Cost for the Stepper Motors is minimal compared to the labor to gain access to them. There are more than one Stepper Motor within the Plenum.
One controls Outside Air, one controls Heat/Defrost distribution, one controls amount of heated air going to Heat/Defrost and there are possibly more. Therefore there is Considerable Cost Savings in having them ALL replaced at once because the Plenum is accessed once to replace them all.

Dec 07, 2009 | 2000 Chevrolet Silverado 1500

3 Answers

Drivers side rear door will not lock. or unlock, with FOB or main lock control on drivers side front door. I have to loc and unlock this door manually


THE DOOR LOCK ACTUATOR IS BAD THIS WHAT CONTROLS THE LOCK ELECTRONICALLY. WHAT IT IS THAT GET HOT AND THE CONTROL GETS HOT SO MANY TIMES BURNS UP CONTRFOL CONTACT. THE ONLY FIX IS TO REPLACE THE ACTUATOR.

Jul 17, 2009 | 2000 Toyota Camry

1 Answer

Fan switch works on only one speed


  1. Disconnect and isolate the battery negative cable.
  2. From the passenger foot well area, remove the two hex screws used to secure the blower motor resistor.
  3. Unplug the front blower motor resistor from the wire harness connector.
  4. Pull the front blower motor resistor and its wire harness out of the plenum panel and through the cowl plenum access hole far enough to access the wire harness connector.
  5. Remove the front blower motor resistor from the cowl plenum.
INSTALLATION
  1. Plug the blower motor resistor into the wire harness connector.
  2. Install the blower motor resistor to the cowl plenum panel by feeding the resistor and wire harness back through the cowl plenum access hole.
  3. Install and tighten the two screws that secure the resistor to the HVAC unit Tighten the screws to 2.2 Nm (20 in. lbs.) .
  4. Connect the battery negative cable

May 27, 2009 | 2001 Dodge Dakota

1 Answer

Electric door lock mafunction


Door lock/unlock actuator (motor) has gone bad in the passenger side. Get the actuator from a Hyundai Parts dealer (or junk yard if you trust them) and replace it yourself OR take it to a Hyundai Service Center and they'll do it for you.

May 12, 2009 | 2003 Hyundai Tiburon

2 Answers

Heater blower


your blower resistor is bad

Apr 21, 2009 | 2001 Dodge Durango

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...