Question about 1993 Chevrolet Suburban

1 Answer

I have a 1998 suburban, I have driver side brake and turn signal, nothing else and nothing on the passenger side, any ideas

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

I had this same problem. It was a circuit board inside the tail light assembly. You can buy them as a pair at most part stores

Posted on Jan 13, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

psds4
  • 293 Answers

SOURCE: no turn signals or side brake lights on 94 chevy suburban

the problen is probably the turn signal switch with a test light check for power at brake switch if no power check for power at turn signal switch the brake lights are incorperated through the turn signal switch

Posted on Oct 18, 2008

  • 740 Answers

SOURCE: 96 Cavalier passenger rear brake lock up when wet or cold

Bad PROPORTION VALVE ... the back brakes should only be doing 30% of the stopping with a bad proportion valve it will send more pressure to the back during braking and cause it to lock up. Good Luck and thanks for using FIX YA

Posted on Jan 04, 2009

  • 1 Answer

SOURCE: Passenger brake (only) locks up when cold or wet

Same here guys damn brakes stick can only go in reverse. However i do find storing the car in a warm garagef yo can get there) usally will fix the problem after a few kicks to the bck ties whne the cars warmed up

Posted on Mar 26, 2009

rteemon
  • 578 Answers

SOURCE: 1998 Buick Century Driver-side blows hot, passenger side cold

vent your vent port one your port may be block or you temperature sensor giving trouble

Posted on Jul 01, 2009

  • 3 Answers

SOURCE: Driver Heated Seat 03 Suburban

Identical thing here with my '03 Surburban LT.

Posted on Aug 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I'm having trouble with my brake lights on my 07 Colorado both brake lights dont work the passenger side running light works but the driver side doesn't both turn signals work the high mount brake light...


There is a module on the passenger side behind the rear wheel mounted to the body. It goes bad. On the drivers side is where the grounds are located, on or close to the frame. Check these first.

Mar 19, 2015 | Cars & Trucks

2 Answers

ELECTRICAL PROBLEM


take it to a body shop

Nov 27, 2013 | 2000 Dodge Stratus

1 Answer

I have a 1990 Chevy Suburban v1500. All lights work except for the Brake Lights and Turn Signals. The Blinker switch on steering column is broken, other than that everything is fine.


Yes, the brake light signal on American cars is routed through the turn signal switch. A new switch should restore both your turns and your brake lights.
American cars use the same bulb filament and same wire to the rears for both brakes and turns. Press the brakes when turning and both rear brakes will light, but since one side travels through the flasher relay, that side will blink, while the other side has a steady light.

Apr 06, 2013 | 1990 Chevrolet Suburban

1 Answer

No brake light or hazard,turn signal


On 1998 Lincoln Town Car 4.6L SFI 8cyl the Flasher is located: Seating area, driver side, behind dash, mounted on passenger side of steering column. Check it.

Hope helps (remember to rate and comment this answer).

Jul 09, 2011 | 1998 Lincoln Town Car

2 Answers

Tail lights work on both sides. turn signal and


Sounds like you need to replace the drivers brake/tail light.

Dec 14, 2009 | 1998 GMC Sierra

1 Answer

DRIVER SIDE TAIL LIGHT BRAKE LIGHT OR TURN SIGNAL DONT WORK BUT P


if you have the diagram,have a look for a ground problem.ground the assembly to the side that works.the other thing to do if you have a test light is check that there is 12 volts on off on the signal on one bulb pin and steady 12v on the run and stop lights.that means there is an open ground......

Jun 13, 2009 | 1991 Chevrolet Suburban

2 Answers

No turn signals or side brake lights on 94 chevy suburban


the problen is probably the turn signal switch with a test light check for power at brake switch if no power check for power at turn signal switch the brake lights are incorperated through the turn signal switch

Oct 18, 2008 | 1994 Chevrolet Suburban

Not finding what you are looking for?
1993 Chevrolet Suburban Logo

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...