Question about 2002 Chevrolet Malibu

Open Question

I have a brocken rack and pinion chassis mount bracket what i can do to mount my rack and pinion on 20002 malibu

Left side chassis mount bracket broken

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 76109 Answers

SOURCE: my 1999 plymouth breeze has a power steering leak

A-1 CARDONE Part # 22347 {[Rack & Pinion] Complete Unit; Reman.}
Reman.; Hydraulic Power Steering; Includes Inner Tie Rodssource: www.rockauto.com sounds like a rack seal. $236.89

Posted on Jul 17, 2009

Ad
  • 242 Answers

SOURCE: trying to find the part and actual name for this

You will not be able to get this at a parts store. From what you are describing, this sounds like the bracket that the mount bolts to-commenly refered to as the motor mount stand. Either will have to get at the dealer or salvage yard.

Posted on Sep 12, 2009

SOURCE: I'm looking for the engine mounting bracket for

That will be a dealer or junkyard only part. Check out GMparthouse.com, they have exploded view diagrams with parts prices and discounts on oem parts. I gave it a quick look and it looks like they have what you need and it seems to be about $40. Good luck.

Posted on Nov 26, 2009

Testimonial: "Yes this is the part and I thank you for what you all do. I was unable to find this with many searches. Once again thank you. "

  • 740 Answers

SOURCE: replace rack and pinion

get it as high off the ground as possible (lift if possible) disconect lines tierod ends and pull all bolts holding it on and it sould just slip out of the wheel well

Posted on Jan 11, 2010

  • 3640 Answers

SOURCE: Need picture of alternator assembly with brackets 99 Malibu

go to any auto parts store and buy a haynes manual for your car. they are based on a complete teardown of vehicle. this book should show you. only about 20 to 25 bucks, good- luck!

Posted on Jul 29, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you replace the rack and opinion on a 92 cutlass ceira


Here you are - power rack & pinion.

Except 2.2L and 1993-96 3.1L Engines
See Figure 1
  1. Raise the intermediate shaft seal and remove intermediate shaft-to-stub shaft pinch bolt.
  2. Remove the air cleaner and disconnect the pressure hoses from the steering gear.
  3. Raise and support the vehicle on jackstands, then remove both front wheel and tire assemblies.
  4. Remove the cotter pins and nuts from both tie rod ends. Using tool J-6627 or BT-7101, press the tie rod ends from the steering knuckle.
  5. If equipped with an Air Management pipe, remove the bracket bolt from the crossmember.
  6. Remove the 2 rear cradle mounting bolts and lower the rear of the cradle about 4-5 in. (102-127mm).

WARNING
If the rear of the cradle is lowered too far, the engine components nearest the cowl may be damaged.
  1. If equipped, remove the rack and pinion heat shield.



Fig. Fig. 1: Power rack and pinion assembly
  1. Remove the rack and pinion mounting bolts, then the gear assembly through the left wheel opening.
To install:
  1. Install the gear assembly through the left wheel opening and install the mounting bolts.
  2. Install the heat shield.
  3. Raise the rear of the cradle and install the mounting bolts.
  4. Install the bracket bolt to the crossmember under the air management pipe.
  5. Install the tie rod ends to the steering knuckles, install the retaining nuts and insert new cotter pins.
  6. Install the front wheels and lower the vehicle.
  7. Install the high pressure hoses to the steering gear and install the air cleaner.
  8. Install the intermediate shaft seal and the intermediate shaft-to-stub shaft pinch bolt.
2.2L Engine
  1. Disconnect the negative battery cable.
  2. Install an engine support fixture J-28467-A, or the equivalent.
  3. Raise and safely support the vehicle.
  4. Remove the tire and wheel assembly.
  5. Remove the intermediate shaft lower pinch bolt.
  6. Disconnect the intermediate shaft from stub shaft.

CAUTION
Failure to disconnect the intermediate shaft from the rack and pinion stub shaft can result in damage to the steering gear and/or intermediate shaft. This damage can cause loss of steering control which could result in personal injury.
  1. Remove the exhaust pipe hanger bracket near rear of frame including the brake line retainer and rubber exhaust pipe hangers.
  2. Remove the engine and transaxle mount nuts at the subframe.
  3. Support the rear of the subframe with jack stands.
  4. Remove the rear subframe bolts and discard.
  5. Lower the subframe for access to rack and pinion.
Do not lower the rear of the cradle too far, as damage to engine components nearest the cowl may result.
  1. Remove the cotter pins and castle nuts from the outer tie rod ends and separate the tie rod ends from the steering knuckles using a suitable puller.
  2. Disconnect the power steering lines from the steering gear.
  3. Remove the rack and pinion mounting bolts and nuts.
  4. Remove the rack and pinion through left wheel opening.
To Install:
  1. Install the rack and pinion through left wheel opening.
  2. Install the rack and pinion mounting bolts and nuts and tighten to 66 ft. lbs. (90 Nm).
  3. Connect the power steering lines to the rack using new O-rings and tighten the fittings to 13 ft. lbs. (17 Nm) on the return line and 21 ft. lbs. (28 Nm) on the pressure line.
  4. Install the power steering line clip to steering gear.
  5. Connect the tie rod ends to the steering knuckles. Tighten the castle nuts to 31 ft. lbs. (42 Nm). Install new cotter pins.
  6. Raise the subframe into position and install new frame mounting bolts. Tighten the bolts to 103 ft. lbs. (140 Nm).
  7. Remove the jack.
  8. Install the engine mount and transaxle mount nuts and tighten to 39 ft. lbs. (53 Nm).
  9. Install the exhaust pipe hanger bracket near the rear of frame including brake line retainer and rubber exhaust pipe hanger.
  10. Connect the intermediate shaft to the stub shaft and tighten the pinch bolt to 29 ft. lbs. (40 Nm).
  11. Install the tire and wheel assembly.
  12. Lower the vehicle.
  13. Remove the support fixture.
  14. Connect the negative battery cable.
  15. Refill the power steering reservoir and bleed the system.
  16. Check the front end alignment and adjust as necessary.
3.1L Engine (VIN M)
  1. Disconnect the negative battery cable.
  2. Remove engine torque strut from engine.
  3. Install an engine support fixture J-28467-A, or the equivalent.
  4. Raise and safely support the vehicle.
  5. Remove the tire and wheel assembly.
  6. Remove the cotter pins and castle nuts from the outer tie rod ends and separate the tie rod ends from the steering knuckles using a suitable puller.
  7. Remove the center engine and rear transaxle mounts from the frame.
  8. Remove the intermediate shaft lower pinch bolt.
  9. Disconnect the intermediate shaft from stub shaft.

CAUTION
Failure to disconnect the intermediate shaft from the rack and pinion stub shaft can result in damage to the steering gear and/or intermediate shaft. This damage can cause loss of steering control which could result in personal injury.
  1. Remove the brace bolts and brace, including brake line brace.
  2. Support the rear of the subframe with jack stands.
  3. Remove the rear subframe bolts and discard.
  4. Lower the subframe for access to rack and pinion.
  5. Remove the steering gear heat shield.
  6. Remove the clip holding lines at rack assembly.
  7. Disconnect the power steering lines and O-rings.
  8. Remove the rack and pinion mounting bolts and nuts.
  9. Remove the rack and pinion unit through the left wheel well.
To Install:
  1. Install the rack and pinion through left wheel opening.
  2. Install the rack and pinion mounting bolts and nuts and tighten the mounting bolts to 66 ft. lbs. (90 Nm).
  3. Connect the power steering lines to the rack using new O-rings and tighten the fittings to 13 ft. lbs. (17 Nm) on the return line and 21 ft. lbs. (28 Nm). on the pressure line.
  4. Install the power steering line clip to steering gear.
  5. Install the steering gear heat shield.
  6. Raise the subframe into position and install new frame mounting bolts. Tighten the bolts to 103 ft. lbs. (140 Nm).
  7. Remove the jack.
  8. Install the engine mount and transaxle mount nuts and tighten to 39 ft. lbs. (53 Nm).
  9. Install the brace and bolts including brake line brace.
  10. Connect the intermediate shaft to the stub shaft and tighten the pinch bolt to 29 ft. lbs. (40 Nm).
  11. Connect the tie rod ends to the steering knuckles. Tighten the castle nuts to 31 ft. lbs. (42 Nm). Install new cotter pins.
  12. Install the tire and wheel assembly.
  13. Lower the vehicle.
  14. Remove the support fixture.
  15. Connect the negative battery cable.
  16. Refill the power steering reservoir and bleed the system.
  17. Check the front end alignment and adjust as necessary.

25936701-ge4w2xkagkibehwv23tkbbb2-2-0.gif

Nov 01, 2015 | Cars & Trucks

1 Answer

How to replace rack an pinion cutlass ciera 1992


You aren't saying what engine is in it, or whether it is manual or power steering. Here is the R/R procedure for power steering rack for all engine sizes.

Except 2.2L and 1993-96 3.1L Engines
See Figure 1
  1. Raise the intermediate shaft seal and remove intermediate shaft-to-stub shaft pinch bolt.
  2. Remove the air cleaner and disconnect the pressure hoses from the steering gear.
  3. Raise and support the vehicle on jackstands, then remove both front wheel and tire assemblies.
  4. Remove the cotter pins and nuts from both tie rod ends. Using tool J-6627 or BT-7101, press the tie rod ends from the steering knuckle.
  5. If equipped with an Air Management pipe, remove the bracket bolt from the crossmember.
  6. Remove the 2 rear cradle mounting bolts and lower the rear of the cradle about 4-5 in. (102-127mm).

WARNING
If the rear of the cradle is lowered too far, the engine components nearest the cowl may be damaged.
  1. If equipped, remove the rack and pinion heat shield.



Fig. Fig. 1: Power rack and pinion assembly
  1. Remove the rack and pinion mounting bolts, then the gear assembly through the left wheel opening.
To install:
  1. Install the gear assembly through the left wheel opening and install the mounting bolts.
  2. Install the heat shield.
  3. Raise the rear of the cradle and install the mounting bolts.
  4. Install the bracket bolt to the crossmember under the air management pipe.
  5. Install the tie rod ends to the steering knuckles, install the retaining nuts and insert new cotter pins.
  6. Install the front wheels and lower the vehicle.
  7. Install the high pressure hoses to the steering gear and install the air cleaner.
  8. Install the intermediate shaft seal and the intermediate shaft-to-stub shaft pinch bolt.
2.2L Engine
  1. Disconnect the negative battery cable.
  2. Install an engine support fixture J-28467-A, or the equivalent.
  3. Raise and safely support the vehicle.
  4. Remove the tire and wheel assembly.
  5. Remove the intermediate shaft lower pinch bolt.
  6. Disconnect the intermediate shaft from stub shaft.

CAUTION
Failure to disconnect the intermediate shaft from the rack and pinion stub shaft can result in damage to the steering gear and/or intermediate shaft. This damage can cause loss of steering control which could result in personal injury.
  1. Remove the exhaust pipe hanger bracket near rear of frame including the brake line retainer and rubber exhaust pipe hangers.
  2. Remove the engine and transaxle mount nuts at the subframe.
  3. Support the rear of the subframe with jack stands.
  4. Remove the rear subframe bolts and discard.
  5. Lower the subframe for access to rack and pinion.
Do not lower the rear of the cradle too far, as damage to engine components nearest the cowl may result.
  1. Remove the cotter pins and castle nuts from the outer tie rod ends and separate the tie rod ends from the steering knuckles using a suitable puller.
  2. Disconnect the power steering lines from the steering gear.
  3. Remove the rack and pinion mounting bolts and nuts.
  4. Remove the rack and pinion through left wheel opening.
To Install:
  1. Install the rack and pinion through left wheel opening.
  2. Install the rack and pinion mounting bolts and nuts and tighten to 66 ft. lbs. (90 Nm).
  3. Connect the power steering lines to the rack using new O-rings and tighten the fittings to 13 ft. lbs. (17 Nm) on the return line and 21 ft. lbs. (28 Nm) on the pressure line.
  4. Install the power steering line clip to steering gear.
  5. Connect the tie rod ends to the steering knuckles. Tighten the castle nuts to 31 ft. lbs. (42 Nm). Install new cotter pins.
  6. Raise the subframe into position and install new frame mounting bolts. Tighten the bolts to 103 ft. lbs. (140 Nm).
  7. Remove the jack.
  8. Install the engine mount and transaxle mount nuts and tighten to 39 ft. lbs. (53 Nm).
  9. Install the exhaust pipe hanger bracket near the rear of frame including brake line retainer and rubber exhaust pipe hanger.
  10. Connect the intermediate shaft to the stub shaft and tighten the pinch bolt to 29 ft. lbs. (40 Nm).
  11. Install the tire and wheel assembly.
  12. Lower the vehicle.
  13. Remove the support fixture.
  14. Connect the negative battery cable.
  15. Refill the power steering reservoir and bleed the system.
  16. Check the front end alignment and adjust as necessary.
3.1L Engine (VIN M)
  1. Disconnect the negative battery cable.
  2. Remove engine torque strut from engine.
  3. Install an engine support fixture J-28467-A, or the equivalent.
  4. Raise and safely support the vehicle.
  5. Remove the tire and wheel assembly.
  6. Remove the cotter pins and castle nuts from the outer tie rod ends and separate the tie rod ends from the steering knuckles using a suitable puller.
  7. Remove the center engine and rear transaxle mounts from the frame.
  8. Remove the intermediate shaft lower pinch bolt.
  9. Disconnect the intermediate shaft from stub shaft.

CAUTION
Failure to disconnect the intermediate shaft from the rack and pinion stub shaft can result in damage to the steering gear and/or intermediate shaft. This damage can cause loss of steering control which could result in personal injury.
  1. Remove the brace bolts and brace, including brake line brace.
  2. Support the rear of the subframe with jack stands.
  3. Remove the rear subframe bolts and discard.
  4. Lower the subframe for access to rack and pinion.
  5. Remove the steering gear heat shield.
  6. Remove the clip holding lines at rack assembly.
  7. Disconnect the power steering lines and O-rings.
  8. Remove the rack and pinion mounting bolts and nuts.
  9. Remove the rack and pinion unit through the left wheel well.
To Install:
  1. Install the rack and pinion through left wheel opening.
  2. Install the rack and pinion mounting bolts and nuts and tighten the mounting bolts to 66 ft. lbs. (90 Nm).
  3. Connect the power steering lines to the rack using new O-rings and tighten the fittings to 13 ft. lbs. (17 Nm) on the return line and 21 ft. lbs. (28 Nm). on the pressure line.
  4. Install the power steering line clip to steering gear.
  5. Install the steering gear heat shield.
  6. Raise the subframe into position and install new frame mounting bolts. Tighten the bolts to 103 ft. lbs. (140 Nm).
  7. Remove the jack.
  8. Install the engine mount and transaxle mount nuts and tighten to 39 ft. lbs. (53 Nm).
  9. Install the brace and bolts including brake line brace.
  10. Connect the intermediate shaft to the stub shaft and tighten the pinch bolt to 29 ft. lbs. (40 Nm).
  11. Connect the tie rod ends to the steering knuckles. Tighten the castle nuts to 31 ft. lbs. (42 Nm). Install new cotter pins.
  12. Install the tire and wheel assembly.
  13. Lower the vehicle.
  14. Remove the support fixture.
  15. Connect the negative battery cable.
  16. Refill the power steering reservoir and bleed the system.
  17. Check the front end alignment and adjust as necessary.

25936687-ge4w2xkagkibehwv23tkbbb2-2-0.gif

Nov 01, 2015 | Cars & Trucks

1 Answer

How to replace the rack and pinion on a 01 chevy malibu


how to change rack and pinion on Malibu 2001

Jan 20, 2013 | 2001 Chevrolet Malibu

1 Answer

99 Olds alero will only turn to the right. On quick inspection found that the rack and pinion moves with turning the wheels. Is it supposed to?


The whole rack & pinion does NOT move! Only the rod out of either end of it. If the main body, where the hoses connect, is moving the mounting bolts are missing, or broken.

Normally any vehicle with rack & pinion steering, that will not turn left equals a bad rack & pinion.
The "wont turn left" is the classic industry wide indicator that the rack & pinion is worn out.

Aug 21, 2011 | 1999 Oldsmobile Alero

1 Answer

What holds the rack to the car its like its not monted


CHECK RACK AND PINION MOUNTING BRACKETS FOR MISSING OR LOOSE BOLTS.

Oct 15, 2010 | 1992 Lexus Es 300

2 Answers

I have a 96 intrepid with a quarter revolution to the right of play before i can make a right turn.i believe the steering coupler is out.can this be repaired effectively, or should the rack and pinion be...


hi you should replace the whole rack and pinion, as if any other part has damage, this will end up damaging the new parts and you will be back to stage one, i do not think it would be cost affective as well as the parts will possibly cost just as much as a new rack, also you would have labour charges to..hope this helps

Oct 10, 2010 | 1996 Dodge Intrepid

2 Answers

Hard steering effort all the time Sterring wheel jerking when turning left


check your fluid. but it sounds like the steering rack is on its way out

Feb 08, 2010 | 1997 Chevrolet Malibu

1 Answer

2002 pontiac grand am rack and pinion replacement how to


Removing the rack and pinion assembly from a 2002 Pontiac Grand Am Se To get the old rack and pinion off of the car for replacement involves lowering the sub-frame, removing the stabilizer bar, and pulling the rack out from the driver side of the vehicle.
  • Start by lifting or jacking up the car and removing the front wheels. Once the car is safely supported, disconnect both tie rods from the steering knuckles.
  • The rear motor mount sits on top of the cross-member part of the sub-frame, and must be disconnected to allow the sub-frame to drop a few inches. Remove the three bolts attaching it to the center of the sub-frame - one in the back and two in the front near the back of the transmission.
  • Loosen the two bolts holding the front of the sub-frame. Place a scissor jack or bottle jack under the rear of the sub-frame where the bolt for the motor mount was. Remove the two smaller bolts from each side of the rear of the sub-frame (total 4 bolts) and then loosen the two remaining larger bolts holding the rear of the sub-frame (these bolts go through the rear control arm bushings and are very long) until the bolts are only going through the control arm bushing, and not into the chassis. You do not need to remove these completely.
  • Remove the stabilizer links from both sides.
  • Next you must disconnect the steering linkage. This is done easily by lifting up the rubber boot to expose the small bolt holding the linkage. Remove the bolt and pry the linkage upward using a pry tool or screw driver.
  • Near the passenger side of the crossmember, remove the bolt holding the power steering line bracket to the chassis. You may now begin to lower the sub-frame using the jack. The front bolts should have lowered the sub-frame about a half-inch or so, allowing you to lower the back of the sub-frame 3 or 4 inches.
  • With the sub-frame lowered, you can now access the bolts holding the stabilizer bar in place. The right side has a nut screwed onto the top of it holding the power steering lines, remove this first, then remove both bolts. Pry or pull the stabilizer brackets up and out. Remove the stabilizer bar.
  • Now you can get to both of the bolts holding the rack in place. Remove both of these, then begin to slide the rack toward the driver side wheel well until there is no more slack in the power steering lines. At this point you should be able to get to the nuts securing the lines on the rack. Loosen both nuts and be ready with something to cap the ends with. I used part of a plastic bag and a wire to tie it. You can now pull the rack out through the driver side.
  • Be sure to replace the rubber o-rings on the ends of the lines when putting the new rack in. Replace everything in the reverse order. Put your tie rods on the new rack, making sure to count the turns or make a mark or measure to be sure your tie rods end up close to the same length as before.
  • Bleed the power steering system.

Important: Get an alignment! Not only is it dangerous to drive with your steering out of align but it will also grate the tread off your tires in a matter of weeks or even days.

Oct 27, 2009 | 2002 Pontiac Grand Am

1 Answer

2004 malibu looses power steering


sounds like the rack and pinion has gone bad. have a shop do it. the car will need to be aligned after a new rack is installed.

Aug 06, 2009 | 2004 Chevrolet Malibu

Not finding what you are looking for?
2002 Chevrolet Malibu Logo

Related Topics:

95 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...