Question about 2006 Dodge Caravan

1 Answer

What causes obd code u110c

I was having a emmision test done for license renewal and the tesr failed because of code in obd the test requires hooking up computer to obd

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 183 Answers

U110C-NO FUEL LEVEL BUS MESSAGE
When Monitored and Set Condition:
U110C-NO FUEL LEVEL BUS MESSAGE
When Monitored: Ignition on.
Set Condition: No fuel level BUS messages received by the PCM for 20 seconds.
POSSIBLE CAUSES
DTC RESET
COMMUNICATE WITH BCM
FUEL LEVEL BUS MESSAGE
PCI BUS CIRCUIT OPEN FROM PCM TO BCM
BCM
TEST ACTION APPLICABILITY
1 NOTE: If a fuel level circuit or performance DTC is set along with P1681,
diagnose the circuit/performance DTC before continuing.
Turn the ignition on.
With the DRBIIIt, erase DTCs.
Start the engine on and off several times. Leave the engine running for at least 20
second each time.
With the DRBIIIt, read DTCs.
Does the DTC reset?
All
Yes ! Go To 2
No ! Refer to the INTERMITTENT CONDITION symptom in the
Driveability category.
Perform POWERTRAIN VERIFICATION TEST VER - 1 - NGC.
2 Ignition on, engine not running.
With the DRBIIIt, attempt to communicate with the BCM.
Can communication be established with the BCM?
All
Yes ! Go To 3
No ! Refer to the Communication Category and perform the appropriate
symptom related to no communication with BCM.
Perform POWERTRAIN VERIFICATION TEST VER - 1 - NGC.
3 Turn the ignition on.
Using the DRBIIIt, read the Fuel Level parameter in the PCM.
Does the DRBIIIt display a fuel level value?
All
Yes ! Replace and program the Powertrain Control Module in accordance
with the Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 1 - NGC.
No ! Go To 4
287
DRIVEABILITY - NGC
TEST ACTION APPLICABILITY
4 Turn the ignition off.
Disconnect the PCM harness connectors.
Disconnect the BCM harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMINALS
RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the PCI Bus circuit from the BCM harness connector to the
appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?
All
Yes ! Replace BCM in accordance with the Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 1 - NGC.
No ! Repair the PCI Bus circuit between the PCM and the BCM for an
open.
Perform POWERTRAIN VERIFICATION TEST VER - 1 - NGC
__________________

Posted on Jan 13, 2013

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
66 chrgr
  • 1011 Answers

SOURCE: emmisions failure with code P0406

you need to replace the egr solenoid to fix this problem any shop can do this .

Posted on Apr 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Po410 code /failed emmision test


the following link explains the 410 code and possible solution ---check the air pump unit wiring and fuses for disconnect or damage as to the technical service bulletin (tbs) it is for the small suv /pick up
http://www.obd-codes.com/p0410

May 21, 2016 | 2000 Oldsmobile Intrigue

1 Answer

I HAVE FAILED EMMISIONS PASSED ALL BUT READINESS RESULTS. CODE 99999..OBD


Read the article in the link below and it will explain how the readiness monitor tests work.

http://ricksfreeautorepairadvice.com/readiness-monitors-and-drive-cycles/

Mar 09, 2015 | 2000 GMC Jimmy

1 Answer

What causes obd code u110c


Read this please:

The BCM then puts the fuel level info out on the communications bus for interested modules. The PCM isn't getting the message and is turning on the MIL and setting a 'lack of communication' fault code (U110C).

Jan 13, 2013 | Cars & Trucks

1 Answer

If emmisions are okay is my catalytic convertor ok


You might want to check out the OBD trouble code site I will post the link for you...http://www.obd-codes.com/p0302

Sep 01, 2012 | 2004 Mazda RX-8

1 Answer

97 Buick Lesabre, had emmisions test done (which it passed) as soon as leaving emmisions test check engine light came on. Any ideas what may have caused this?


Stop by any good parts store (Autozone, Advance, etc) and have them do a FREE OBII scan. It will read all your fault codes and more than likely light came on because of emission test. But have them read the faults and reset your light.

Feb 23, 2011 | 1997 Buick LeSabre

1 Answer

Check enging light on 2003 Acura TLS doesn't come on when starting car. Failed emmision test because of it.


There is a problem with your OBDII (Onboard Diagnostics -2) system. The only way to find out why your Check Engine light is on is to scan your engine computer and find out which part of the system is failing. There will be fault codes stored in the computer to tell you. The failing system will then need to be diagnosed to locate the actual cause of the failure. Once this is completed, the computer will have to be reset, and the car will have to be driven (sometimes for several days) to get all of the computer monitors to run and recheck the system. If the repairs are successful, the same codes should not return. You may have new codes show up however. This is because some of the monitors are unable to run if the check engine light is on due to another failure. Sometimes a code like "Catalyst Efficiency Below Threshold" will show up when they were not there before. This is because driving the vehicle with the Check Engine light on has destroyed the catalytic converters, but the code could not set previously because the catalyst monitor could not run to test the catalyst when the other problem was present. Now that the first problem has been corrected, the catalyst monitor now runs and has determined that the catalyst has been damaged.

This why I tell all my customers that the best time to get your car ready for an emissions test, is the minute the Check Engine light comes on. Ignoring this light and driving the vehicle with it on can damage some pretty expensive parts, as well as possibly costing you fines for not getting your vehicle "Legal" when it is time to renew licenses, etc. I live in Missouri, and you cannot renew your license plates without passing the emissions test - people wait until the last day to renew their registration and they get angry with me when I tell them it is going to take several days and possibly even a couple weeks to get their car to pass. It's not MY fault!!! THEY are the ones who chose to ignore the warning lamp!

Feb 06, 2011 | 1996 Acura TL Series

1 Answer

I have a toyota corolla 2003 and recently went for an emissions test and passed. The day after my emission test, the engine light went on. I tried to unscrew and rescrew the gas tank cap, but it didn't...


After tightening the gas cap, you will have to drive the car a few 'cycles' before the light goes off. If that doesn't work, have the trouble codes read to find out exactly what is wrong and causing the light to illuminate.

Jan 04, 2011 | 2003 Toyota Corolla

1 Answer

How do you reset the code for the cadalyc converter


Your local auto parts store can reset your computer with an obd-ll scanner(as long as check engine light is on)..or you could simply disconnect the battery for about 15 min. This will not mask mechanical issue with your catalytic converter or 02 sensors whichever case may be..It will only clear the code and give your car's computer a chance to re-run its emmision tests..Check engine light will be back if an emmisions part has failed or needs repair..All this to the best of my knowledge with the information provided.....Hope this helps and best of luck with your automotive endeavors.

btw, the autostore(advance auto, autozone, etc...) will normally give you a printout of your cars obd-ll codes(which cause check engine light to illuminate) if you ask. They may even offer up some guidance but keep in mind they"re trying to sell parts.

Oct 15, 2010 | 1998 Mazda Protege

1 Answer

Did not pass state inspection (vehicle)


First the fault codes,
U110C is No Fuel Level Bus Message
U0155 is No Cluster Bus Message.
Unfortunatly you have to be able to communicate with the instrument cluster with your scanner to diagnoise and I do not think an aftermarket scanner can do this.




Mar 02, 2010 | 2005 Chrysler PT Cruiser

Not finding what you are looking for?
2006 Dodge Caravan Logo

325 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...