Question about 1995 Dodge Grand Caravan

1 Answer

Left door latch on 1995 caravan

I need to assemble rods that go in the door and dont know where or how they attach.  i need a diagram

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 840 Answers

You should not need a diagram the long one goes to handle and the other gos to lockor latch they are attached by retainers that go around the rods

Posted on Jan 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i take off the inside drivers door panel on a 2005 dodge caravan


Hi Roberta, here's the instructions on how to remove your door panel. I have to wonder though on why you are removing it, my guess is you window doesn't roll up or down and your replacing the regulator. Any way here goes.

REMOVAL

  1. Remove the plug and remove screw attaching door pull cup to inner door panel.
  2. Remove switch bezel and disconnect power window/memory switch.
  3. Remove screws attaching trim panel to door from below map pocket.
  4. If equipped, remove window crank. (Refer to 23 - BODY/DOOR - FRONT/WINDOW CRANK - REMOVAL)
  5. Remove screw holding door trim to door panel from behind inside latch release handle .
  6. Disengage clips attaching door trim to door frame around perimeter of panel.
  7. Lift trim panel upward to disengage flange from inner belt molding at top of door.
  8. Tilt top of trim panel away from door to gain access to latch linkage.
  9. Disengage clip attaching linkage rod to inside latch release handle (INSIDE DOOR HANDLE LINKAGE).
  10. Separate linkage rod from latch handle.
  11. Disconnect the power door switch, courtesy lamp electrical connectors.
  12. Remove front door trim panel from vehicle.
Hope this helps and have an awesome day Roberta!

May 21, 2014 | 2005 Dodge Grand Caravan

1 Answer

1995 caravan child lock stays locked even when lever is moved to unlock position


Then you must change out the door latch inside the door. Here is how you do that.
REMOVALLabor Operations: Click to display a list of Labor Operations associated with this procedure


NOTE:For power sliding door procedures refer to POWER SLIDING DOOR SYSTEM in the ELECTRICAL section.1.Remove sliding door trim panel.2.Remove sliding door stop bumper.3.Peel watershield away from adhesive around perimeter of inner door panel.
4.Disengage external cable from latch/lock asseembly.5.Remove foam block.6.Remove inside door handle assembly.7.Disengage inside cable from latch/lock assembly.8.Disengage link from bellcrank.9.Disengage hold open latch cable from lower hinge.
10.Remove bolts attaching latch/lock control to sliding door.11.If equipped, lower latch and disconnect wire connector from power door lock motor.12.Remove latch/lock from door.

Jun 21, 2012 | 1995 Dodge Caravan

2 Answers

Rear pontiac grand am door stuck


I have a 2002 pontiac grand am with both power windows and door locks. Everything else works except the lock assembly on the rear driver side rear door latch. I have removed the inside panel , aboth rods are connected. all power is disconnected to that door. I moved both of the rods correctly and the door will slightly open but that is all. How can I get it to release so I can repair or replace the latch and lock if nescessary ? I had the same problem only reversed with the frond door it would not close but after some trying I fixed that problem.

Apr 04, 2012 | Pontiac Grand Am Cars & Trucks

1 Answer

I need help on removing door panel on 2000 Dodge Caravan - window fell in dorr and I can not seem to get the panel off. Any suggestions?


Answer
FRONT DOOR TRIM PANEL
REMOVAL
Using a trim stick (available from parts stores), pry courtesy lamp from door trim.
Disconnect wire connector from courtesy lamp.
If equipped, remove screws attaching door assist handle to inner door panel.
If equipped, remove screw attaching door pull cup to inner door panel.
If equipped, remove screws attaching trim panel to door from below map pocket.
If equipped, remove window crank.
Using a trim stick, remove screw cover from switch panel.
Remove screws attaching switch panel to door trim.
Remove power accessary switch from door trim Front Door Switch Panel
Disconnect power switch from wire connector.
If equipped, using a small, flat bladed pry tool, remove memory seat/mirror switch and disconnect wire connector Memory Seat/Mirror Switch
If equipped, remove screw holding door trim to door panel from behind inside latch release handle.
Disengage clips attaching door trim to door frame around perimeter of panel Front Door Trim Panel
Lift trim panel upward to disengage flange from inner belt molding at top of door.
Tilt top of trim panel away from door to gain access to latch linkage.
Disengage clip attaching linkage rod to inside latch release handle Inside Door Handle Linkage
Separate linkage rod from latch handle.
Remove front door trim panel from vehicle.
INSTALLATION
Hold top of trim panel away from door to gain access to latch linkage.
Place linkage rod in position on latch handle.
Engage clip to hold linkage rod to inside latch release handle.
Place front door trim panel in position on door.
Install trim panel into inner belt molding at top of door.
Install clips to attach door trim to door frame around perimeter of panel.
If equipped, install screw to attach door trim to door panel behind inside latch release handle.
If equipped, connect power switch into wire connector.
Place power accessary switch in position on door trim.
Connect wire connector into memory seat/mirror switch and install switch into trim panel.
Install screws to attach accessary switch panel to door trim.
Install screw cover into switch panel.
If equipped, install window crank.
If equipped, install screws to attach trim panel to door inside map pocket.
If equipped, install screw to attach door pull cup to inner door panel.
If equipped, install screws to attach door assist handle to inner door panel.
Connect wire connector into courtesy lamp.
Install lamp in door trim.

Feb 02, 2012 | 2000 Dodge Caravan

1 Answer

How to remove door panel on 2003 grand caravan



  1. Remove the plug and remove screw attaching door pull cup to inner door panel.
  2. Remove the switch bezel and then disconnect the power window-memory switch.
  3. Now you need to remove the screws attaching the trim panel to the door from below map pocket.
  4. If you have a window crank remove this now.
  5. Remove the screw holding the door trim to the door panel from behind -inside latch release handle .
  6. Now disengage the clips attaching the door trim to the door frame around the outside of the panel.
  7. Lift the trim panel upward to disengage the flange from the inner belt molding at the top of the door.
  8. Now tilt the top of trim panel away from door to gain access to the linkage on the latch.
  9. Now you need to disengage the clip that attaches the linkage rod to the inside latch release handle - this is the inside door handle linkage.
  10. Now just separate the linkage rod from the latch handle.
  11. Now you disconnect the power door switch and the courtesy lamp connectors.
  12. Now you can remove the door trim panel up and out.


  • Hope this helps and thank you for using FixYa.

Regards, Tony

Jul 23, 2011 | 2003 Dodge Caravan

1 Answer

How does the door linkage work i.e a diagram


There are plastic connectors that attach to the rod and attach to the latch. The rod usually hooks into the inside latch, the rod may be held to the door by some clips. Then the rod connects to the latch with a plastic retainer clip.

Mar 13, 2010 | 1993 Honda Civic 4 Door

2 Answers

The drivers front door will not open from the inside. The interior door handle won't activate the mechanism to open the door. Yet, the exterior door handle will open the door. Please advise! Thank you!


It could be the latch, but look to see if the interior door handle rod is still connected to the latch assembly. You will need to remove the interior door panel.

Jan 27, 2010 | 1995 Oldsmobile Cutlass Ciera

1 Answer

Trying to remove door latch on 1995 thunderbird. Car has power locks.


inside or outside latch? please rate

Section 01-14A: Handles, Locks, Latches and Mechanisms 1995 Thunderbird, Cougar Workshop Manual
REMOVAL AND INSTALLATION Latch, Door Removal and Installation
  1. Remove front door trim panel (23942) and watershield from front door (20124). Refer to Section 01-05 .
  1. Mark the location of the bolt retaining front door glass run front retainer (21572). Remove the bolt.
  1. Check all rod connections against the appropriate illustration. Correct any disconnected or loose connections and check operation before replacing parts.
  1. Remove power door lock actuator (218A42).
  1. Disconnect the rods from the front door latch (21812) . The front door latch remote control link (21940) and the latch-to-lock cylinder rod cannot be removed because of the rod's end configuration. Remove wiring from clip on front door latch shield.
  1. Remove front door latch control cylinder rod (22134) from the door lock cylinder (21985).
  1. Remove front door latch remote control and link (21818).
  1. Remove the front door latch retaining screws. Disconnect the door open warning lamp switch (14018) , if so equipped. Remove the front door latch from the front door .
  1. NOTE: Do not damage anti-theft shield.
    Remove anti-theft shield from the front door latch .
  1. Remove front door latch remote control link , front door latch control cylinder rods , and door open warning lamp switches from front door latch , where applicable.
  1. To install, reverse Removal procedure. Tighten front door latch retaining screws 4-8 Nm (36-70 lb-in).
3e933ef.gif

Item Part Number Description 1 21852 Front Door Latch Push Button Rod 2 21940 Front Door Latch Remote Control Link 3 386656-S Bushing 4 21978 Door Latch Shield 5 218A42 Power Door Lock Actuator 6 22134 Front Door Latch Control Cylinder Rod 7 21812 Front Door Latch
------------------------------------------------------------------------------------
Remote Control Assembly Door Latch
Removal and Installation
  1. Remove front door trim panel (23942) and watershield. Refer to Section 01-05 .
  1. Remove screw and washer assembly retaining front door latch remote control and link (21818) to front door (20124) .
  1. Rotate front door latch remote control and link to remove from front door latch remote control link (21940) .
  1. To install, reverse Removal procedure.

Sep 27, 2009 | 1995 Ford Thunderbird

1 Answer

Rear door on driver side won't open,have taken the panel off the inside of car,seems like the lock won,t travelas far as it does on the other door.is there any way to open this door,thanks[1997 lincoln...


Rear
Removal
  1. Using a small screwdriver, remove the screw cover from the armrest of rear door trim panel (27406).
  1. Remove the two retaining screws.
  1. Using Trim Pad Removing Tool from Rotunda Windshield and Moulding/Trim Removal Kit 107-R0401 or equivalent, pry rear door trim panel from door inner panel.
  1. Disconnect electrical connectors.
Installation
  1. Position rear door trim panel on door inner panel, aligning two locators on rear door trim panel. Reverse Removal procedure.
------------------------------------------------------------------------------------ Rear
Removal
  1. Remove door trim panel and watershield. Refer to Section 01-05 .
  1. Check all connections of remote control links and cables. Service as necessary.
  1. Remove remote control assembly.
  1. Remove door latch remote control assembly from latch assembly.
  1. Drill out rivet at bellcrank and link (264B14).
  1. Remove three screws attaching latch assembly to door.
  1. Drill out rivet that attaches actuator motor to door.
  1. Remove latch assembly with actuator motor and door latch control rod lever link assembly.
Installation
  1. Install new bushings and clip onto latch assembly.
  1. Install latch with links and power lock actuator into door cavity.
  1. Position latch assembly to door, aligning screw holes in latch and door. Install three screws. Tighten to 10-13 Nm (89-115 lb-in).
  1. Attach door latch actuator motor to door with a new rivet.
  1. Install bellcrank and link to door using a new rivet.
  1. Install inside door handle and remote control assembly to door.
  1. Open and close door to check latch assembly operation.
  1. Install watershield and door trim panel. Refer to Section 01-05 .
ee8a11f.gif
Item Part Number Description 1 221A00 Door Handle to Door Latch Actuating Cable 2 26446 Rear Door Control Rod Retainer 3 377901 Plug Button 4 26412 Rear Door Latch 5 W623451-S2 Push Nut 6 224A32 Counter Balance 7 22450 Door Outside Handle Tension Spring 8 W701210-S309 Screw 9 224A20 Outside Door Handle Anti Rattle Pivot (2 Req'd) 10 22404 Door Handle 11 224A24 Front Door Outside Handle Spacer (2 Req'd) 12 264A64 Rear Door Actuating Rod 13 22408 Outside Door Handle Anti-Rattle Bumper 14 22428 Outside Door Handle Large Pad 15 N621906-S2 Nut (2 Req'd) 16 N807329 Screw (3 Req'd) 17 26595 Rear Door Electric Latch Actuator (RH) 18 W701566-S47 Rivet 19 431C04-A Rear Door Latch Striker Assembly 20 — Door Lock Striker Plate (Part of Door Shell Assy) 21 W525172-S Rivet (2 Req'd) 22 264B14 Bellcrank and Link (RH) 23 264A50 Bushing 24 N802034-SG Rivet 25 26420 Rear Door Latch Control Rod Link 26 W525172-S Rivet (2 Req'd) 27 21818 RR Door Latch (Inside) 28 A26460 RR Door Latch Push Button Rod 29 21982 Door Latch Rear Striker Assembly 30 N808377-S101 Screw (2 Req'd) 31 250A04 Rear Door Catch 32 N801010-S100 Truss Head Bolt (2 Req'd) 33 N804234-S2 Screw 34 266A74 Rear Door Latch Actuator Retainer 35 24630 Rear Door 36 26552 Rear Door Latch Control Escutcheon A — Tighten to 21-29 Nm (16-21 Lb-Ft) B — Tighten to 10-13 Nm (89-115 Lb-In) C — Tighten to 7-8 Nm (62-70 Lb-In) D — Tighten to 26-34 Nm (20-25 Lb-Ft) E — Tighten to 3-4 Nm (27-35 Lb-In)

Mar 24, 2009 | 1997 Lincoln Continental

1 Answer

Handle-to-Latch rod assembly


hook them to the latch first but make sure they are routed right. what ever you do dont bend the rods it will never open right if you do.

Jul 30, 2008 | 1998 Jeep Cherokee

Not finding what you are looking for?
1995 Dodge Grand Caravan Logo

Related Topics:

157 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...