Question about 1997 Chevrolet Blazer

2 Answers

1998 Chevy Blazer making clicking noise in front

I have a 1998 Chevy Blazer it is making a clicking noise in the front when it is in 2 wheel but when it's in 4wd it stops. I changed the CV shaft but it is still making the same noise. Does anyone know what this could be? Please help!

Posted by on

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 51 Answers

Slim possibility it could be a bearing too. When it's not under load and is free-wheeling (2wd) the stress on the hub assembly changes, making the clicking more noticeable. When under a load, being driven, the pressure on the bearing would be more steady (in 4wd) and might make it less noticeable, if at all.

Posted on Feb 08, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 11 Answers

Check the ft diff actuater. Sounds like the ft diff isn't complelely disengaging when in 2 wheel drive. Also I'm not sure but I think that the fr driveshaft should not be turning when in 2 wd. If it is turning then you could have a problem with the transfercase.

Posted on Jan 23, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What causes a popping noise from front end, and a rubbing noise , not grinding


4wd?? Check CV shafts. Also look for whats rubbing. whre is the dirt rubbed off.

Feb 26, 2016 | 2005 GMC Yukon

1 Answer

Need to take rear driveline out of 1998 chevy blazer


By removing the drive line you may move the car but it will lock up on you at some point,, the rear end, wheel bearing or broken axel will cause more damage, just tear into it and fix the problem before it causes you more trouble.....Hope that helps...

Feb 26, 2015 | 1998 Chevrolet Blazer

1 Answer

Noise front left wheel


check the adjustment of the wheel bearings . Check the drive shaft and cv joints

Mar 19, 2014 | 2003 Chevrolet Silverado 1500

1 Answer

Clicking noise when in 4WD


Front drive shaft CV going bad or CV axle going bag

Jan 30, 2014 | Dodge Durango Cars & Trucks

1 Answer

Front wheel


Drive shaft CV joint?

Jan 17, 2014 | 1998 Jeep Cherokee 4WD

1 Answer

I have a 1996 Chevy Blazer. A few days ago, I heard a clunking / grinding noise from underneath when I was turning. Sense, then it has gotten worse and got to the point that it was loud and vibrated the...


This truck should not be operated on the street in 4WD mode. You need to investigate the front axel CV axel shafts as well as the outer axel carrier bearings. Damage to front brake rotors and possible lock down while operating the vehicle. Safety hazard exist, so do not drive until axel and bearings are checked and repaired

Aug 23, 2017 | 1996 Chevrolet Blazer

1 Answer

2000 chevy blazer passenger front wheel noise


driving in 4wd on hard surfaces produces what is known as torque wind up as the wheels cannot slip so the variations of distance going around corners , dips in the road etc place considerable strain on the transmission , transfer case , drive lines and diffs
that is why it is difficult to get out of 4wd unless you drive with 2 wheels on a grass verge to relieve that torque wind up
as for the noise check wheel bearings and the cv ("U") joint at that wheel as there appears a proble where the dog teeth in the hub are not engaging properly or are jumping out of engagement

Mar 26, 2017 | 2000 Chevrolet Blazer

1 Answer

Vibration NOISE in front end of 2000 Chevy Blazer. Any suggestions??


Check the front wheel bearings .... very common . While driving turn the wheel gently from side to side and see if the noise changes .. this will load and unload the bearings.

Feb 12, 2011 | 2000 Chevrolet Blazer

3 Answers

Clicking sound like a turn signal constantly until brakes are applied, what would cause it? 1998 chevy blazer s10


The brake pads have a tab on them that can be bent to take up slack against the caliper. If they are not tight they can rattle back and forth making noise until the brakes are applied. Hope it helps.

Oct 05, 2010 | 1998 Chevrolet Blazer

Not finding what you are looking for?
1997 Chevrolet Blazer Logo

862 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...