Question about 1999 Dodge Intrepid

Open Question

I need the torque specs and pattern for a 98 dodge intrepid 3.2 for the heads?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 218 Answers

SOURCE: I need some torque specs for the connecting rod

20 FT LBS + A 1/4 TURN

Posted on May 04, 2009

Ad
hotrodshop
  • 106 Answers

SOURCE: I need the torque spec for camshafts / 98 Dodge Neon 2.0 dohc

Here is the factory torque chart for all fasteners on the 2.0L

TORQUE CHART 2.0L DOHC DESCRIPTION TORQUE Camshaft Sensor Pick-Up Bolts 9.6 N·m (85 in. lbs.) Camshaft Sprocket Bolt 115 N·m (85 ft. lbs.) Connecting Rod Cap Bolts 27 N·m (20 ft. lbs.) Plus 1/4 Turn Collar - Oil Pan to Transaxle Step 1: Collar to Oil Pan Bolts 3 N·m (30 in. lbs.) Step 2: Collar to Transaxle Bolts 108 N·m (80 ft. lbs.) Step 3: Collar to Oil Pan Bolts 54 N·m (40 ft. lbs.) Crankshaft Main Bearing Cap/Bedplate M8 Bedplate Bolts 30 N·m (22 ft. lbs.) M11 Main Cap Bolts 81 N·m (60 ft. lbs.) Crankshaft Damper Bolt 142 N·m (105 ft. lbs.) Cylinder Head Bolts Refer To Cylinder Head Installation Cylinder Head Cover Bolts 12 N·m (105 in. lbs.) Drive Plate to Crankshaft Bolts 95 N·m (70 ft. lbs.) Engine Mount Bracket Bolts 61 N·m (45 ft. lbs.) Exhaust Manifold to Cylinder Head Bolts 23 N·m (200 in. lbs.) Exhaust Manifold Heat Shield Bolts 15 N·m (130 in. lbs.) Intake Manifold Bolts 28 N·m (250 in. lbs.) Oil Filter Adapter Fastener 80 N·m (60 ft. lbs.) Oil Filter 20 N·m (15 ft. lbs.) Oil Pan Bolts 12 N·m (105 in. lbs.) Drain Plug 34 N·m (25 ft. lbs.) Oil Pump Attaching Bolts 28 N·m (250 in. lbs.) Oil Pump Cover Fastener 12 N·m (105 in. lbs.) Oil Pump Pick-up Tube Bolt 28 N·m (250 in. lbs.) Oil Pump Relief Valve Cap 55 N·m (40 ft. lbs.) Spark Plugs Plug 28 N·m (20 ft. lbs.) Thermostat Housing Bolts 23 N·m (200 in lbs.) Timing Belt Tensioner Assembly - Mechanical Bolts 28 N·m (250 in. lbs.) Timing Belt Tensioner Assembly - Hydraulic Bolts 31 N·m (275 in. lbs.) Timing Belt T

Posted on Jun 11, 2009

outdoorsman5
  • 631 Answers

SOURCE: head bolt torque specs for 2000 dodge neon 2.0 SOHC

I have the specs and diagrams. If you want me to send them to you, give me your email address. Outdoorsman592003@yahoo.com

Posted on Sep 05, 2009

tneubauer
  • 437 Answers

SOURCE: i need torque specs on 93 dodge 360 ..heads,

Cylinder Head Bolt 5.9L

Step 1 - 50 ftlb
Step 2 - 105 ftlb
Step 3 - Recheck At 105 ftlb

Tightening sequence

Rocker Arm Bolt

5.9L - 17 ftlb

Posted on Jan 23, 2010

ZJLimited
  • 17970 Answers

SOURCE: I need torque specs for the head bolts on a 2004

For 2004 Dodge Stratus 2.4L SFI SOHC 4cyl the Head Bolt Torque sequence
------------ | 10 6 2 3 7 | | 9 5 1 4 8 | ------------

Step: 1 - Torque to 25 ft/lbs
Steps: 2 - Torque to 50 ft/lbs
Steps: 3 - Torque to 50 ft/lbs
Steps: 4 - Turn 90 degreesRecheck final torque in sequence

Caution:Engine uses torque to yield head bolts (TTY) that permanently stretch during initial installation. New head bolts must be used when cylinder headis replaced or re installed to obtain proper torque specification.

Hope helps (remember comment and rated this).

Posted on Aug 02, 2010

Testimonial: "I appreciate your quick response. Thanks"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

WHAT IS THE HARMONIC BALANCER TORQUE SPECS FOR A 2002 2.7L DODGE INTREPID?


This is for a 5.7 Ram
the torque should be 150-180 ft lbs. anywhere in this range is good.
http://www.fixya.com/cars/t8915727-need_know_torque

Register at this website to get all the torque specs.

http://www.autozone.com/repairinfo/repairguide/repairGuideContent.jsp?pageId=0996b43f8037c5e2

Aha, I took me 30 minutes, but here you go. The secret was the change of search query wording to;
2002 2.7 DODGE INTREPID TORQUE SPECS crankshaft damper

(198) Install damper center bolt. Tighten center bolt
while holding the damper with Special Tool 8191 to
170 N•m (125 ft. lbs.) (Fig. 76).

http://www.dodgeintrepid.net/18-general-discussion-second-generation/61664-so-your-2-7-ready-some-100k-repairs.html


WHAT IS THE HARMONIC BALANCER TORQUE SPECS FOR 2002 2 7L DODGE INTREPID...

Jan 11, 2017 | 2002 Dodge Intrepid

1 Answer

03 Dodge Intrepid intake manifold torque specs top & bottom is for 3.5 V6


Lower Intake:
  1. Use a skin coat of RTV silicone on both sides of the water passage ports (outer most holes) and put the new lower intake gaskets into place
  2. Hand tighten the 13mm head intake bolts and Torque the bolts , starting from the center and working your way out in a circular pattern
  3. Torque these bolts in a few small increments until they have reached 250 inch pounds of torque.
  4. Upper Intake Plenum:
  5. When installing the intake air plenum , be sure to catch the four center bolts and the two side bolts (stiffener brackets) before tightening , The center bolts should be torqued to 250 inch pounds .The fuel rail bolts should be torqued to 100 inch pounds

Jun 24, 2016 | 2003 Dodge Intrepid

1 Answer

How much torque for each head bolt in a 2004 Dodge ram 1500 3.7 liter


Install the cylinder heads. Use new gaskets and tighten the bolts, in sequence, as follows:
  1. Step 1: Bolts 1-8 to 20 ft. lbs. (27 Nm)
  2. Step 2: Bolts 1-10 verify torque without loosening
  3. Step 3: Bolts 9-12 to 10 ft. lbs. (14 Nm)
  4. Step 4: Bolts 1-8 plus 1 / 4 (90 degree) turn
  5. Step 5: Bolts 9-12 to 19 ft. lbs. (26 Nm)


26002143-2qxw3km0vcnqu3setvnduoab-2-1.gif

Dec 10, 2015 | Dodge Cars & Trucks

1 Answer

I need to know torque specs and torque pattern for a 2001 head gasket on my 2001 sunfire


HINT: The "torque pattern" on ALL cylinder heads is start in the center and work your way toward the ends. The specifications below are "torque-to yield" or "torque angle" specs. When in doubt, about 65 Ft. Lbs. will work on pretty much ANY aluminum head. The main point is to get them EVEN to prevent warpage.


11_20_2011_2_46_10_pm.gif

Nov 20, 2011 | 2001 Pontiac Sunfire

1 Answer

Need torgue specs & sequence for upper & lower


Lower: Torque to 28 N·m (250 in. lbs.)

Upper: Torque to 12 N·m (105 in. lbs.)

Sequences below:

mf_grimm_1.jpg

mf_grimm_2.jpg

Good luck.

Jul 23, 2011 | 2004 Dodge Intrepid

1 Answer

Need the cylinder head torque specs for a 5.7 TBI 88 chevy 2500 pu


cylinder head torque spec is
step 1, 25 ft-lb
step 2, 45 ft-lb
step 3, 65 ft-lb

bolt tightening pattern
front of vehicle is on left just for referance.
13 5 2 10
17 9 1 6 14

16 12 8 4 3 7 11 15
i hope that makes sense and helps.

Mar 21, 2010 | 1994 Chevrolet C1500

1 Answer

Head bolt torque spec for 98 caravan 2.4 thank you


Cylinder head bolt torque specs:
1st pass 25 ft-lbs
2nd Pass 50 ft-lbs
3rd Pass 75 ft-lbs
Final Pass tighten plus (+)1/4 turn = 90-degrees
BOLT ORDER:
10----6----2----3----7

9----5----1----4----8
START WITH 1 THEN 2 THEN 3 ....ETC.
END WITH 10 = 1ST PASS.

Nov 21, 2009 | 1998 Dodge Caravan

2 Answers

99 dodge intrepid specs


Inner main bearing cap bolts:
Torque to 15 ft-lbs, then rotate an additional 1/4 turn

Outer main (windage tray) bearing cap bolts:
Torque to 20 ft-lbs, then rotate an additional 1/4 turn

Main bearing cap cross bolts:
Torque to 250 in-lbs or 20.83 ft-lbs

Connecting road bearing cap nuts:
Torque to 20 ft-lbs, then rotate an additional 1/4 turn

Apr 21, 2009 | 1999 Dodge Intrepid

1 Answer

Need to the torque specs for a 1999 Dodge Durango


Head Torque sequence Step 1: torque to 50 Ft/Lbs Step 2: torque to 105 Ft/Lbs recheck final torque in sequence.

Torque intake manifold: Step 1: 12 inch/Lbs, (hand tight) Step 2: 72 inch/Lbs, (6) Ft/Lbs Step 3: 12 Ft/Lbs
torque intake plenum: Step 1: 24 inch/lb (hand tight) Step 2: 48 inch/lb (4) Ft/Lbs Step 3: 84 inch/lb (7) Ft/Lbs (To torque bolts, start in center using crisscross pattern)

Apr 07, 2009 | 1999 Dodge Durango

Not finding what you are looking for?
1999 Dodge Intrepid Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8274 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...