Question about 1995 Chevrolet Camaro

2 Answers

What is the part number for a carrier bearing on 1995 chevy camaro

Posted by Anonymous on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

I just replaced my 2 piece drive shaft on my 94 camaro v6 with a one piece off a 96 firebird.works great..

Posted on May 07, 2015

Ad
  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers

(a little late in responding - but maybe someone will need this info).

If you mean the carrier bearing on the driveshaft - then you must have a v6 model. I would advise to skip replacing it and instead purchase a 1pc shaft (no carrier bearing). The cb is located near a Hi-Speed CV Joint which make changing the carrier a little difficult.
A new replacement 1pc driveshaft costs about $225.00
The carrier bearing itself may run $40-$140. ( http://www.fortwayneclutch.com/index.php/driveshaft-parts/carrier-support-bearings/gm/1993-2002-chevy-camaro-v6-pontiac-firebird-v6-carrier-bearing-new-f-body-carrier-bearing-for-v6-models-pn-s-3r80-40.html ) - for reference...
You could also check a junk yard for a 1pc oem shaft (most shafts there are bent or have bad uj's and will cost $$ to have fixed )
>1994-2002 f-body models all have the same length from the seal of the transmission to the center of the uj @ the diff.
>when looking for an oem 1pc shaft you will find them in Steel and Aluminum. Slight differences in length when measuring center to center of the universal joints ( 40 7/8" - 40 1/2" ) - but the slip yokes vary in length, weighted / non-weighted..etc = this will make it appear the the shafts are different.
>>watch out for oem shafts with the weighted slip yoke from manual 6spd v8 models. This slip yoke may hit the trans/exhaust mount that is used on v6 models.!!

Posted on Nov 05, 2014

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

  • 52 Answers

SOURCE: carrier bearing

There are only two bolts that hold the carriier bearing to the crossmemmber under the truck. You do, however, have to remove the drive shaft so that you can get the carrier bearing off of it. It is pressed onto the driveshaft.

Posted on Aug 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i replace the rear axel bearings on a 1988 Chevrolet IROC Z28 Camaro


Put car in neutral, remove wheels, calipers and rotors, diff. cover. rotate carrier until you see wrist pin retaining bolt, remove bolt and slide out the wrist pin out of carrier. Next push axle inward to remove inner axle "C" retainer washer then slide axle out of tube. Then pry off axle seal and with slide hammer w/attachment remove axle bearing.

Feb 23, 2014 | 1988 Chevrolet Camaro

2 Answers

I have a 96 camaro and I need to replace my carrier bearing. Where can I find one?


I am not sure your car has a carrier bearing, but if it did it would be located on the drive shaft between the transmission and rear end of the car.

Apr 22, 2013 | 1996 Chevrolet Camaro

1 Answer

My carrier bearing is bad in my 96 firebird and I can't find another anywhere. No one has heard of a 2 part driveshaft in my car. Can I replace it with a solid driveshaft? Or do you know where I can find a...


If you mean the carrier bearing on the driveshaft - then you must have a v6 model. I would advise to skip replacing it and instead purchase a 1pc shaft (no carrier bearing). The cb is located near a Hi-Speed CV Joint which make changing the carrier a little difficult.
A new replacement 1pc driveshaft costs about $225.00
The carrier bearing itself may run $40-$140. ( http://www.fortwayneclutch.com/index.php/driveshaft-parts/carrier-support-bearings/gm/1993-2002-chevy-camaro-v6-pontiac-firebird-v6-carrier-bearing-new-f-body-carrier-bearing-for-v6-models-pn-s-3r80-40.html ) - for reference...
You could also check a junk yard for a 1pc oem shaft (most shafts there are bent or have bad uj's and will cost $$ to have fixed )
>1994-2002 f-body models all have the same length from the seal of the transmission to the center of the uj @ the diff.
>when looking for an oem 1pc shaft you will find them in Steel and Aluminum. Slight differences in length when measuring center to center of the universal joints ( 40 7/8" - 40 1/2" ) - but the slip yokes vary in length, weighted / non-weighted..etc = this will make it appear the the shafts are different.
>>watch out for oem shafts with the weighted slip yoke from manual 6spd v8 models. This slip yoke may hit the trans/exhaust mount that is used on v6 models.!!

Jul 22, 2012 | Cars & Trucks

1 Answer

Just replaced plugs and wires on a 95 chevy camaro v6 now has no power


Sounds like you may crossed up some plug wires? use the diagram below to check this out as the poss problem. Match the numbers on the coil pack to the cylinder numbers. Cross wiring plug wires is the most common thing that home mechs do that they get wrong.


2_16_2012_4_57_59_pm.gif

Feb 16, 2012 | 1995 Chevrolet Camaro

1 Answer

Rotors on 1991 chevy camaro. are there bearings that need to be pressed into the rotors


there are bearings but they do not have to be pressed in you can use a rubber mallot and tap them into place only the inner bearing needs to be tapped in

Dec 13, 2009 | 1991 Chevrolet Camaro

1 Answer

Need an engine diagram for a 1995 chevy camaro 6 cylinder , 3.4.


go to your chevy dealer parts dept and they should be able to print one for you,you'll need your vin #.

Sep 14, 2009 | 1995 Chevrolet Camaro

1 Answer

Rear end drive gears worn on 95 chevy camaro z 28 causes roaring;grinding noises during operation in all gears ;six speed manual


Make sure it is not just a axle bearing . remove the shaft and rear wheels and brake drums ( if not disc) if disc remove the caliper and rotate the axles listen and feel for roughness.

Aug 29, 2009 | 1995 Chevrolet Camaro

1 Answer

95 chevy camaro 3.4 v6 fire order problem


pass side 1 3 5 from front to back 1 n front 5 n back drive side 2 4 6 2 n front 6 n back

Jan 12, 2009 | 1995 Chevrolet Camaro

Not finding what you are looking for?
1995 Chevrolet Camaro Logo

288 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...