Question about 2004 Mercury Mountaineer
Error code 9352 and E013
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
My name is Dennis and I can assist you to finding your parking brake adjustment location.
1) the adjustment is located so that you have to remove your center console floor finish panel (this is the drink holder).
2) raise your parking brake lever and gently pry the plastic tabs from the center console.
3) Once you can see the park brake lever you will see a nut that is turned to adjust the lever so that it has 5 clicks when it is applied.
Glad to be of assistance and thank you for using FixYa. Please rate the solution because I can learn from your rating (and it keeps my rating up to date). Thank you, Dennis
Posted on Nov 16, 2008
Verify the hand-held transmitter is operative.
Prepare for programming the universal transmitter by erasing all three channels (hold down the two outside buttons until the red light begins to flash [20-30 seconds]). Release both buttons.
Select one of the three universal transmitter channels to be programmed by pressing the desired button
Hold the end of the hand-held transmitter 25-51 mm (1-2 in) from the front surface of the universal transmitter so that the red light can still be seen
Use both hands to press the hand-held transmitter button and the desired button on the universal transmitter. Do not release either button.
Hold down both buttons until the red light on the universal transmitter flashes, first slowly and then rapidly. Release both buttons when the rapid flashing begins. The universal transmitter has successfully learned the new frequency signal and can be used in place of the hand-held transmitter(s).
If the hand-held transmitter appears to program the universal transmitter but does not open the garage door, the garage door opener may have a code protected or rolling code feature.
To operate, simply press the appropriate button on the universal transmitter. The red light is on while the signal is being transmitted.
IF THE GARAGE OPENER HAS ROLLING CODES---
program as above then------
Train the garage door opener receiver to recognize the universal transmitter.
Remove the cover panel from the garage door opener receiver.
Locate the training button on the garage door opener receiver. Location and color of the button may vary by garage door opener manufacturer. Refer to the garage door opener instruction manual or owner literature.
Press the training button on the garage door opener receiver for 1-2 seconds.
Press the programmed universal transmitter button for as long as the universal transmitter red light flashes (1-2 seconds). Release the button and re-press the button to confirm that the universal transmitter is trained to the receiver.
The garage door opener should recognize the universal transmitter.
Posted on Apr 02, 2009
You should be able to visit any Ford or Lincoln dealer and ask the parts department to look up this info. You will need proof of ownership and ID. If by the way you lost the keys you will need 2 keys and have them programmed to the truck.
Posted on Nov 07, 2009
The best way to change it is to flush it out You can do it yourself, but I do not recommend. A shop that is good like a Monro or Firestone usually charges about 100 bucks to flush and that includes the fluid. If you do it yourself, you will save about 60 dollars, but you risk damage to your radiator.
you will need a hose and an adapter. you back out the lower, or upper cooler line for your trans, whichever is the easiest to get to, (Some trucks have an auxiliary engine oil cooler, but make sure you are flushing the trans lines) put the adapter into the rad where you removed the line, and put a hose from each one down into a bucket. Have about 14 qt's of ford trans fluid ready. Put the funnel into the trans dip stick, and start the engine. pour the qts into the dipstick tube while the old fluid is pumped into the bucket. When you have about two gallons pumped into the bucket shut the engine off and reattach the line into the radiator. start up the engine and check your level. Fill with additional fluid if needed.
note: some say you should drop the pan. two things, you only change half the fluid when you do it that way, and second if you need to change the filter because it is clogged, it is too late for the transmission. The filter is only there to protect the valve body, not keep the fluid clean.
Hope this helps
Posted on Nov 22, 2009
Tips for a great answer:
Aug 25, 2014 | 2004 Mercury Mountaineer
Feb 28, 2013 | 2004 Mercury Mountaineer
Oct 07, 2012 | 2004 Mercury Mountaineer
Aug 06, 2012 | 1997 Mercury Mountaineer
Apr 17, 2011 | Mercury Mountaineer Cars & Trucks
Mar 15, 2011 | 2004 Mercury Mountaineer
Feb 25, 2011 | 2004 Mercury Mountaineer
Jan 08, 2011 | Ford Explorer Cars & Trucks
Oct 27, 2009 | 2004 Ford F350
59 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: