Question about Toyota Cars & Trucks

Open Question

Hiace washer nozzle remove

Removal replace

Posted by Anonymous on


2 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 279 Answers

SOURCE: 2006 trailblazer washer wiper nozzle removal

This is how to replace the front washer nozzles. First, mark the location of each wiper blade on the windshield with masking tape. Next, you need to remove the windshield wiper arms from their shafts. Raise the plastic cover at the base of each wiper arm. Remove the nuts from the shafts. The arms are press fit onto the tapered shafts. You will need to rock the arms or use something to pry up on the arms to get them to release from the shafts. I usually place a block of wood down, to prevent damage to the paint, then use a "cats paw" style pry bar to remove the arms. Once the arms are removed, you need to remove the black plastic air inlet grill. The nozzles are mounted to this black plastic grill. Remove the rubber hoses from the nozzles. Using a pair of pliers, squeeze the two locking tabs which hold each nozzle in place. Push up and remove the nozzles.
During reassembly, you must be careful to properly orient the wiper arms back onto their shafts. Orient the arms so that the blades are located at the masking tape locations you made at the start.

Posted on Nov 02, 2014


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

The windshield washer line detached. How do you reattach it without removing the hood?

Needle nose, make sure that the washer nozzle itself has not broken off. if there is a hard piece of plastic inside of the rubber hose you will need to replace the washer nozzle.

Apr 04, 2016 | 2006 Kia Spectra

2 Answers

Where do I add washer fluid for rear window wiper on a 2000 blazer

Open the hatch and look for the fill cap along the sides .

Oct 23, 2015 | Cars & Trucks

2 Answers

2006 trailblazer washer wiper nozzle removal replacement

the nozzles just snap in from the top.... you first pop the cover at the pivot point of the wiper arm to access the nut. remove said nut. remove the wiper arms (a puller is very useful to avoid damage) , then Remove the air inlet grille panel (held in with pushpins and small 1/4in or 9/32in bolts. disconnect the hoses and squeeze the two tabs that hold them in. because they snap in from the top, i have seen people crush and brake their old nozzles with needle nose pliers. pull the hose through the hole and attach it to the new nozzle...... NOT the recommended procedure, rent or buy a puller that looks like a small two jaw gear puller to save yourself a big headache (mine was only $45). good luck

Nov 01, 2014 | 2006 Chevrolet Trailblazer

1 Answer

Im only getting washer fluid out of the drivers side hose. Is there a washer pump I can replace myself

The pump pushes fluid through a single hose that splits into two to deliver washer fluid to the passenger and drivers side washer nozzles. The passenger nozzle is plugged. Try removing it and blowing impressed air through it.

Apr 13, 2013 | 2001 Ford Mustang

1 Answer

Windshield Washer nozzles

try removing the hose at the nozzles and use compressed air and a blower nozzle to blow back out the blockage from the nozzle opening

May 05, 2017 | 2001 Isuzu Rodeo

1 Answer

Where is the wiper motor on my 1999 GMC Yukon?

Windshield Wiper Motor
Removal & Installation
To Remove:

  1. Remove wiper arms.
  2. Remove weatherstrip from cowl.
  3. Remove two cowl vent grille panel screws.
  4. Remove windshield nozzles and hoses.
  5. Remove three cowl vent grille panels.
  6. Disconnect windshield wiper motor electrical connector.
    NOTE: Do not remove crank arm from windshield wiper motor.

  7. Loosen nuts that attach the drive link brackets to the crank arm.
  8. Remove wiper motor crank arm brackets.


  9. Remove three bolts and windshield wiper motor from vehicle.

To Install:

  1. Install windshield wiper motor and three bolts.

    • Torque to: 62 in lbs. (7 Nm)

  2. With right side linkage closest to the windshield wiper motor, install drive
    link brackets to wiper motor crank arm.

    • Torque nuts to: 44 in lbs. (5 Nm)

  3. Connect electrical connector.
  4. Install nozzles and windshield washer hoses to cowl vent grille.
  5. Install three cowl vent grille panels and screws to vehicle.
  6. Install weatherstrip to cowl.
  7. Install wiper arms.

prev.gif next.gif

Oct 30, 2010 | 1999 GMC Yukon

1 Answer

The resovir appear to be full however i am not ablew hen pulling the handle to get the washer fluid to come out i hear the motor working but noting comes out

Often the washer nozzles can get clogged. If you hear the washer pump running, you need to disconncect the small hose from the washer nozzle, and see if you get fluid pumped thru it when you hit your washer switch. If so, you need to unclog or replace the nozzle, and if no fluid is pumped out the hose, you need to remove and inspect the washer pump, as it might be dirty, or failed.

Feb 10, 2010 | 2006 Pontiac Torrent

2 Answers

Windshield washer will not work on my 2005 Dodge Durango

First thing to do is make sure it is full of washer fluid. I know, who would not check that? You would be surprised. Ok, now we know it is full so why is it not working? Did you check the fuse. Normally you can hear it try to work by having the hood open while you stand there and have someone try it. It is full and fuse is good and it is trying to pump then either the pump is working but not really pumping anything or what I suspect is more likely is that the spray nozzles are clogged with wax. This is very common and I have seen it time and time again. Remove one of the rubber hoses from a spray nozzle and see if it it pumping out fluid. If it is not, then the pump is bad and must be replaced. It it is pumping fluid then the nozzles are clogged. Use a fine needle to clean out the nozzles. You may have to take the nozzle off in order to clean it throughly. More than likely once you probe inside the nozzles with the needle they will start working. If you end up having to remove the nozzles, and they are metal, which they normally are, you can place them in a pan of boiling water. This will for sure clean them out. The hot water will soften the wax and make it easy to pick and blow out. Have a great 2010, and good luck getting your washer fixed.

Jan 10, 2010 | 2005 Dodge Durango

1 Answer

Wash wipe on a Focus 2000 model

I blieve it's the same pump taht runs the rear and front washers.

The windshield washer comprises the following parts:
  • Windshield washer reservoir, below the front left-hand fender
  • Washer pump, on the outside of the washer reservoir
  • Two washer nozzles on the hood/bonnet, adjustable.
Windshield Washer Pump and Reservoir Removal
All vehicles
  1. Remove the windshield washer reservoir filler neck.
  1. Raise and support the vehicle. For additional information, refer to Section 100-02 .
  1. Remove the right-hand fender splash shield (wheel shown removed for clarity).
  1. Remove the washer reservoir.
    • Disconnect the electrical connectors.
    • Pull off the hoses.
  1. Remove the windshield washer pump with rubber gasket (shown with reservoir installed).
    1. Disconnect the electrical connector.
    1. Disconnect the hoses.
    1. Lift out the pump.

Feb 27, 2009 | 2000 Ford Focus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts


Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides