Question about 2008 Ford Focus

Open Question

What is the felt rear wheel well liner called on focus 2008

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rear suspension sway axle side


could be rear wheel bearings - they come as a complete assy with brake hub - approx $45 each side - 1 hour per side for replacement. Also replace the rear sway bar links $8 for a set - other than that you could have a bent wheel and or loose rear control arm bolts - remove the rear wheels and check all mounting bolts - I had this problem and my rear end felt like it was shimming when I went around corners - 5 minute fix

Oct 27, 2013 | 2000 Ford Focus

1 Answer

How do you replace the drivers side low beam headlight on the 2008 GMC Acadia?


{: ) REMOVE THE LEFT FRONT WHEELHOUSE LINER
The wheelhouse liner is sometimes called the mud guard or the splash shield, whatever.
You may remove the left front tire.

-Start removing all those push pins and #7mm screws. No need to remove the entire liner. You may loosen only the half portion, just enough clearance for your arms to reach inside and aim for the rear of the headlamp.

-Reach for the Headlamp Bulb Accessory Cover. Rotate the cover counterclockwise and remove.

-Release the bulb from the headlamp assembly (turn counterclockwise) Disconnect the electrical connector. Just remember the positioning of the bulb so you can swiftly reinstall a new bulb.

Jun 16, 2011 | 2008 GMC Acadia

1 Answer

How to replace headlight bulbs on 08 malibu ltz


To replace the headlight bulb, remove the front wheel and inner fender liner. You'll now have access to the rear of the headlamp and the rest is plug and play.

Jan 18, 2010 | 2008 Chevrolet Malibu

1 Answer

How do I change the headlight bulb in a 2008 Chevrolet HHR?


Access to change the headlamp bulbs is through the wheel well. The recommended method is to remove the front tire and then the plastic inner fender liner. Once removed, you'll have easy (more or less) access to the rear of the headlamp housing.

Dec 19, 2009 | 2008 Chevrolet Hhr

1 Answer

I want to fit a towbar to my ford focus hatch 2008 model. What is involved in removing rear bumper Regards Brian Lamb


Pop the Hatchback open and remove the connectors
from the top of the bumper cover.

Optional Step: Using a Floor Jack, raise both sides
of the car in the back, supporting both sides with
jack stands, and remove the rear wheels.

Using Torx Bits, remove the inner rear wheel well
lining.

Get behind the rear wheel well and loosen the bolts
holding the bumper brackets on. They're pretty
difficult to find and remove. Be Patient. Do the
same to the other side.

Remove the rear bumper cover by pulling the cover
outward from the part nearest the wheel on both
sides. Once removed, take off the 2 black mounting
brackets from the bumper cover.

Oct 27, 2009 | 2007 Ford Focus (3 Door) Hatchback

1 Answer

Are there any pictures showing where to attach the freon canister to on my 2003 Ford Focus air conditioner?


The low pressure port is behind the passenger fender liner. Remove the right front tire so you can remove the liner.

Detach the wheel arch trim panel on the passenger's side (driver's side shown).
  • Remove six bolts.
  • Remove the trim panel.
63bbe7a.gif

Jun 25, 2009 | 2000 Ford Focus

1 Answer

I believe i have a clogged fuel filter on my 2000 ford focus


Your fuel filter is behind the drivers side wheel liner remove the drivers front wheel then remove the splash shield liner and you will see it mounted to the body of the car .

Jun 10, 2009 | 2000 Ford Focus

1 Answer

Where is the ac recharge port on my 2003 ford focus?


the low pressure port is behind the passenger fender plastic wheel liner.
Remove the screws and pull out the liner and it's right there. Please give highest rating if this is what you need.

    1. Detach the wheel arch trim panel on the passenger's side (driver's side shown).
    2. Remove six bolts.
    • Remove the trim panel.
  • a61e7ee.gif

    Apr 23, 2009 | 2000 Ford Focus

    1 Answer

    Burned out license plate bulb


    open trunk,

    remove felt liner from rear of trunk, (liner directly behind rear lights in side trunk) should be 4 plastic Phillips head screws. Loosing screws, then slowly peel liner away. You will see 3 nuts on each side, removing these nuts will loosing the rear light lenses, so you can pull the lense away from the body from the out side to gain access to the license plate bulbs. Re-install in reverse order. While in there I would recommend replacing your brake light and reverse light bulb. Hey your already in there might as well do a little preventive maintance.

    Dec 12, 2008 | 1995 Lexus ES 300

    Not finding what you are looking for?
    2008 Ford Focus Logo

    Related Topics:

    66 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    yadayada
    yadayada

    Level 3 Expert

    75197 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    fordexpert

    Level 3 Expert

    5481 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...