Question about Hyundai Motor 2002 Elantra

Open Question

Gear shifter assembly

I need to know how to put together my new gear shifter for my 2002 hyundai elantra. It is brand new so all the parts are not together.

Posted by on

6 Suggested Answers

  • 1 Answer

SOURCE: how to install a new clutch in my 2002 hyundai elantra

Yes, I have that I was just hoping for a few details.

Posted on Nov 11, 2008

  • 1986 Answers

SOURCE: Adjustment headlights '02 Hyundai Elantra

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Posted on Oct 06, 2009

ghost45
  • 1280 Answers

SOURCE: 2002 hyundai elantra radio and dome light not working

Then 1, bulbs are burned out
OR 2, the wiring is faulty.

Posted on Nov 04, 2009

Testimonial: "thanx for the solution. took the car to a repair shop and was told that the wiring was faulty. had the car rewired."

MauiRentaCar
  • 288 Answers

SOURCE: 2000 Hyundai elantra transmission delay, reverse going

Did you check the transmission fluid level? If necessary, add fluid. However you probably have a more serious problem. Take the car to a qualified transmission mechanic.

Posted on Feb 27, 2010

  • 171 Answers

SOURCE: how to replace 2002 hyundai elantra hub and bearing

With the car on ground, break loose the drive-axle nut, and the wheel nuts , than jack up the car, support it properly, remove the wheel ,remove the axle-nut.
Remove the brake caliper assembly-- support it properly.
Remove the two bolts that hold the hub bracket to the Macpherson strut assemble, remove the lower arm ball joint and remove the steering tie- rod ball-joint attached to the hub bracket. That's it.Slide off the hub /with the bracket off the drive-shaft.
Follow steps backwards to assemble back.

Posted on Apr 09, 2010

SOURCE: 2000 hyundai elantra alarm goes off where is the

my alarm goes on and off by itself its a 2010 elantra.would like to know how to fix. thank you

Posted on Sep 15, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1997 Hyundai Elantra - in storage over winter. Can't put into gear when running. Can put into gear when turned off - can then start, clutch depressed, can release clutch and drive but can't shift...


clutch &pressure plate must have got moisture on it & forze together put car in gear & turn car over it should brake free had it hapen to me

May 25, 2011 | 1997 Hyundai Elantra

1 Answer

Car will only drive in reverse gear


check the shifter cable to see if broken. put the emergency brake on, have someone look on top of transmission at the shifter linkage to see if it travels into the gears while you move the shifter back and forth. if it's going into all the gears on transmission, i suggest that you also check the fluid in transmission to see if it has proper level of fluid. hope this helps!!!

Aug 23, 2010 | 2000 Hyundai Elantra

1 Answer

Stick shift


Hi:
The shift pattern is pretty much the same on all 5 speed cars. The top row is the odd numbers, 1-3-5
the bottom row is 2-4-Reverse. The center position is neutral

Here is the key: The shifter is slightly spring-loaded to the center position. If you hold in the clutch pedal and pull the shifter to neutral, and let go of it, it will automatically be lined up in the position, that if you pushed it forward , it would go to 3rd gear, and if you pulled it back, it would go into 4th gear.
This way, to start driving, you start out in neutral, grab the shifter lightly, and push it first to the left, then forward. This is first gear, where you start out. when you want to shift to second, push in the clutch, and keeping left pressure on the shifter, pull all the way back . Here is the easy part, 2nd to 3rd. When you are ready, push in the clutch, and just push the gear shift forward , till it hits neutral, and is spring loaded to the middle. Then you just push it straight forward to 3rd, then next shift, straight back to 4th.
Last gear, 5th: push forward to the neutral row, then Push to the right till it lines up ,and forward to the 5th gear. Reverse should only be shifted into from a dead stop. Find neutral, push the shifter all the way right, then pull back towards you. Hope this helps.
Practice a bunch in the driveway!

Apr 21, 2010 | 2001 Hyundai Elantra

1 Answer

How to replace 2002 hyundai elantra hub and bearing


With the car on ground, break loose the drive-axle nut, and the wheel nuts , than jack up the car, support it properly, remove the wheel ,remove the axle-nut.
Remove the brake caliper assembly-- support it properly.
Remove the two bolts that hold the hub bracket to the Macpherson strut assemble, remove the lower arm ball joint and remove the steering tie- rod ball-joint attached to the hub bracket. That's it.Slide off the hub /with the bracket off the drive-shaft.
Follow steps backwards to assemble back.

Apr 09, 2010 | Hyundai Motor 2002 Elantra

1 Answer

Is it possible to put a shift boot with a custom shifter on at automatic 01 hyundai elantra to make it look like a standard?


yes, jus need to get a booth with a bibig enough base to cover shifter base and get o costom shifter knob from auto shop

Aug 23, 2009 | 2001 Hyundai Elantra

2 Answers

92 escort gear problems


sounds like the shifter is worn out, replace the bushing at the shifter and the transmission.

Aug 07, 2009 | Hyundai Motor 2002 Elantra

1 Answer

Can't get car in or out of gear


Throwout bearing will need to be replaced most likely. Otherwise cluctch plate or fork may have stuck

Aug 06, 2009 | Hyundai Motor 2002 Elantra

3 Answers

Hyundai elantra 2002 something loose under the car


Need more info.
Does it do it in gear, in park?
Is it constant?
Try checking the heat shield at the catalytic converter. These sometimes come loose and make a rattling noise when the engine is running.

Jun 03, 2009 | Hyundai Motor 2002 Elantra

1 Answer

Timing Belt Markings


Mark are on the crank and cam timing gears. Cam gear mark at 12 o"clock crank gear mark lined up with TGC mark on block when installing timing belt.

Dec 16, 2008 | Hyundai Motor 2002 Elantra

1 Answer

Hyandai elantra


2008 Elantra still under warranty.

Aug 02, 2008 | 2008 Hyundai Elantra

Not finding what you are looking for?
Hyundai Motor 2002 Elantra Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...